• Proceedings of the KIEE Conference
• /
• 2004.10a
• /
• pp.160-163
• /
• 2004

A passive lossless turn-on/turn-off snubber network is proposed for the boost PWM converter. Previous AC/DC PFC Boost Converter perceives feed forward signal of output for average current-mode control. Previous Boost Convertor, the Quantity of input current will be decreased by the decrease of output current in light load, and also Power factor comes to be decreased. Also the efficiency of converter will be decreased by the decrease of power factor. The proposed converter presents the good PFC, low line current harmonic distortions and tight output voltage regulations using energy recovery circuit. All of the semiconductor devices in the converter are turned on under exact or near zero voltage switching(ZVS). No additional voltage and current stresses on the main switch and main diode occur. To show the superiority of this converter is verified through the experiment with a 640W, 100kHz prototype converter.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.23 no.1
• /
• pp.16-23
• /
• 2018

PM synchronous motor may be rotated to an arbitrary direction and speed by outside wind under natural condition in cases where the fan is applied outside, such as in vehicle radiators and outdoor air-conditioners. Sensorless controls that cannot detect rotor position requires additional sensorless control algorithm because a rotor is rotated by an external load. In this study, the sensorless control of a PM synchronous motor under naturally rotating condition is proposed. The natural rotation conditions are classified as forward high-speed rotation, reverse high-speed rotation, and low-speed rotation. Experiment results verify the performance of the sensorless control, including the rotor speed and position detection at natural rotation mode and switch to the closed-loop sensorless control.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.23 no.1
• /
• pp.9-15
• /
• 2018

This study investigates a bidirectional quasi-Z-source inverter (Bq-ZSI) system with bidirectional power transfer capability and a modified space vector modulation scheme for reducing the ripple of the inductor current. By replacing the diode in the impedance network with an active switch, the power flow can be bidirectional. The average inductor current of the Bq-ZSI network is negative in the regenerative braking mode, thereby regenerating the power. In addition, modified space vector modulation scheme is applied to the Bq-ZSI to control shoot-through time effectively. A 5 kW prototype is built and tested to implement the proposed system. Experimental results show that the Bq-ZSI system is capable of regenerative braking of the induction motor and that the modified space vector modulation method is efficient.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.23 no.2
• /
• pp.129-138
• /
• 2018

Previous single-phase transformerless inverters used active bypass switching circuits that need auxiliary power switches to minimize ground leakage current. However, switching and gate driving losses are increased due to the use of additional power switches. To cope with this drawback, this work proposes a transformerless inverter using a passive bypass filter without any auxiliary power switch. The operation and control of the proposed inverter are described. The ground leakage current characteristics are analyzed for the proposed inverter with the passive bypass filter. The experimental results of the proposed inverter for a 1.0kW prototype system are presented.

• Journal of Power Electronics
• /
• v.14 no.5
• /
• pp.815-826
• /
• 2014

An improved bridgeless interleaved boost power factor correction (PFC) rectifier to improve power efficiency and component utilization is proposed in this study. With combined conventional bridgeless PFC circuit and interleaved technology, the proposed rectifier consists of two interleaved and magnetic inter-coupling boost bridgeless converter cells. Each cell operates alternatively in the critical conduction mode, which can achieve the soft-switching characteristics of the switches and increase power capacity. Auxiliary blocking diodes are employed to eliminate undesired circulating loops and reduce current-sensing noise, which are among the serious drawbacks of a dual-boost PFC rectifier. Magnetic component utilization is improved by symmetrically coupling two inductors on a unique core, which can achieve independence from each other based on the auxiliary diodes. Through the interleaved approach, each switch can operate in the whole line cycle. A simple control scheme is employed in the circuit by using a conventional interleaved controller. The operation principle and theoretical analysis of the converter are presented. A 600 W experimental prototype is built to verify the theoretical analysis and feasibility of the proposed rectifier. System efficiency reaches 97.3% with low total harmonic distortion at full load.

• Proceedings of the KIPE Conference
• /
• 2019.11a
• /
• pp.46-48
• /
• 2019

본 논문은 Discontinuous Conduction Mode(DCM) 플라이백 컨버터로 생성한 고전압 펄스를 스파크 갭으로 펄스 상승 시간을 줄이는 방법에 관하여 다룬다. 이러한 방법으로 생성된 빠른 상승률 특성을 가지는 고전압 펄스 전원장치는 친환경 가스 처리 분야에 사용할 수 있다. 기존 스태킹 구조의 펄스 전원 장치는 많은 수의 스위치들과 에너지 저장 소자가 필요하므로 부피가 커지고 제조 단가가 증가하는 반면, 분 논문에 제안된 전원 장치는 구조를 단순화하여 전체 시스템의 소형화 및 제조 단가를 낮춘 점을 특징으로 한다. 제안된 설계 토폴로지는 플라이백 변압기 2차 측에 다이오드의 사용 유무에 따라 두 개의 변형된 회로로 응용 가능 하다. 변압기 2차측에 다이오드를 사용하면, 음의 성분 없이 깨끗한 고전압 출력 펄스를 만들 수 있지만 사용한 다이오드의 전압 정격을 고려해야 한다. 다이오드를 사용하지 않는다면, 고전압 출력 펄스에 음의 성분이 발생하지만 비용과 부피를 최대한 줄일 수 있다. PSIM 시뮬레이션을 사용하여 제안하는 전원 장치의 23kV, 0.5 ㎲, 10 ns rising time의 출력 펄스 발생 성능을 검증하고, 다이오드 사용에 따른 출력 펄스의 차이점을 비교하였다.

• Journal of international Conference on Electrical Machines and Systems
• /
• v.1 no.1
• /
• pp.8-16
• /
• 2012

Fixed speed wind turbine generators system that uses induction generator as a wind generator has the stability problem similar to a synchronous generator. On the other hand, doubly fed induction generator (DFIG) has the flexibility to control its real and reactive powers independently while being operated in variable speed mode. This paper focuses on a scheme where IG is stabilized by using DFIG during grid fault. In that case, DFIG will be heavily stressed and a remedy should be found out to protect the frequency converter as well as to allow the independent control of real and reactive powers without loosing the synchronism. For that purpose, a crowbar protection switch or DC-link protecting device can be considered. This paper presents a comparative study between two protective schemes, a crowbar circuit connected across the rotor of the DFIG and a protective device connected in the DC-link circuit of the frequency converter. Simulation analysis by using PSCAD/EMTDC shows that both schemes could effectively protect the DFIG, but the latter scheme is superior to the former, because of less circuitry involved.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.12
• /
• pp.3658-3662
• /
• 2010

A new bis-Ru(II) complex, in which two [Ru(1,10-phenanthroline)$_2$dipyrido[3,2-a:2',3'-c]phenazine]$^{2+}$ were tethered by a 1,3-bis(4-pyridyl)propane linker, was synthesized and its binding mode and stoichiometry to DNA was investigated by optical spectroscopy including linear dichroism (LD) and fluorescence intensity measurement. The magnitude of the negatively reduced LD signal of the bis-Ru(II) complex in the dipyrido[3,2-a:2',3'-c]phenazine (DPPZ) ligand absorption region appeared to be similar compared to that in the DNA absorption region, which is considered to be a diagnostic for DPPZ ligand intercalation. The binding stoichiometry measured from its LD magnitude and enhanced fluorescence intensity corresponds to one ligand per three DNA bases, effectively violating the nearest neighbouring site exclusion model for classical DNA intercalation. This observation is in contrast with monomer analogue [Ru(1,10-phenanthroline)$_2$dipyrido[3,2-a:2',3'-c]phenazine]$^{2+}$, which is saturated at the DPPZ ligand to DNA base ratio of 0.25, or one DPPZ ligand per four nucleobases.

• Journal of Communications and Networks
• /
• v.18 no.4
• /
• pp.600-609
• /
• 2016

In this paper, we propose a two-stage base station (BS) sleeping scheme to save energy consumption in cellular networks. The BS sleeping mode is divided into a light sleeping stage and a deep sleeping stage according to whether there is a user in the BS's coverage. In the light sleeping stage, a BS will retain its coverage and frequently switch between the on state and the doze state according to the service characteristics. While in the deep sleeping stage analysis, the BS will shut down its coverage, and neighbor BSs will patch the coverage hole. Several closed-form formulas are derived to demonstrate the power consumption in each sleeping stage and the stage switching conditions are discussed to minimize the average power consumption. The average traffic delay caused by BS sleeping and the average deep sleeping rate under a given traffic load have also been studied. In addition, it is shown that BS sleeping is not always possible because of the limited quality of service (QoS) requirements. Simulation results show that the proposed scheme can effectively reduce the average BS power consumption, at the cost of some extra traffic delay. In summary, our proposed framework provides an essential understanding of the design of future green networks that aim to take full advantage of different stages of BS sleeping to obtain the best energy efficiency.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.49 no.1
• /
• pp.1-8
• /
• 2000

Switched reluctance motor(SRM) has simple magnetic structure, and requires simple power electronic driving circuit. It is very useful for wide range adjustable speed drive system. But, SRM drive generates large vibration and acoustic noise because it is commutated individually by step pulse m.m.f of each phase pole. In the vibration and acoustic noise characteristics. The considerable vibration and noise is induced by radial deforming of stator, so the frequency of dominant vibration and noise is coincident with the frequency of natural mode frequency of mechanical structure. This radial vibration force is generated in the phase commutation region. This paper suggests the new electromagnetic structure of SRM with auxiliary commutation winding which is excited by direct current. This phase and commutation winding are coupled magnetically between one phase winding and the other. Therefore, the switch-off phase current is absorbed by the another phase winding. By this interaction of phase and commutation winding in commutation mechanism, vibration and noise is reduced. And this reduction effect is examined by the test of prototype machine. As a result, SRM with DC exciting commutation winding is very useful to reduce vibration and acoustic noise.