• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2012년도 제38회 춘계학술대회논문집
• /
• pp.457-460
• /
• 2012

본 연구는 7톤급 연소기용 분사기 검증을 위한 축소형 연소기의 설계 및 제작에 관한 것이다. 7톤급 연소기의 헤드부는 90개의 동축 와류형 분사기로 구성되며, 연소실은 케로신 재생냉각 일체형 연소기이다. 7톤급 연소기에 적용할 분사기로 차압 및 리세스 수를 달리한 분사기를 설계하였다. 설계된 분사기를 실물형 연소기에 적용하기 전 축소형 연소기에 먼저 적용하여 분사기 작동성 및 성능검증을 하고자 한다. 축소형 연소기는 분사기 19개로 구성되며, 연소압력 70 bar, 총 추진제 유량은 4.3 kg/s, 혼합비는 2.45이다.

• 대한기계학회논문집B
• /
• 제29권2호
• /
• pp.180-188
• /
• 2005

It is well known that a lean burn engine caused by stratified mixture formation has many kinds of advantages to combustion characteristics, such as higher thermal efficiency and lower CO, NOx levels than conventional homogeneous mixture combustion. Although this combustion can achieve low fuel consumption technology, it produces much unburned hydrocarbon and soot because of heterogeneous equivalence ratio in the combustion chamber. Therefore, the stratified mixture formation technology is very important to obtain the stable lean combustion. In this paper, fundamental studies for stratified combustion were carried out using a constant volume combustion chamber. The local effect of mixture formation according to control air-fuel distribution in the chamber was examined experimentally. In addition, the effect of turbulence on stratified charge combustion process was observed by schlieren photography. From this study, we found that the flame propagation speed increase with swirl flow and the swirl promotes the formation of fuel and air mixture.

• 한국신뢰성학회지:신뢰성응용연구
• /
• 제14권1호
• /
• pp.59-70
• /
• 2014

The requirements of reliability verification for new products and technology are increasing more and more in accordance with the trend of climate change prevention and GHG reduction technology, functional skills. SCA(Swirl Control Actuator) is the important part of a car intake manifold system. This device generates swirl that is mixing the fuel and air into the engine combustion chamber. This is to improve output for engine and reduce the emission for exhaust. In this article reliability assessment criteria for swirl control actuator for automobiles are established in terms of basic HALT and life time test.

• 한국분무공학회지
• /
• 제4권4호
• /
• pp.24-29
• /
• 1999

In the pressure swirl atomizer, the liquid is injected through tangential passages into a swirl chamber, from which it emerges with both tangential and axial velocity components to form a thin conical sheet at the nozzle exit. This sheet rapidly attenuates, finally disintegrating into ligaments and then drops. The purpose of this study is to measure the spray characteristics according to variation of viscosity of the spray produced by the pressure swirl atomizer. The nozzle tested here were especially designed for this investigation. The discharge coefficient is determined by measuring the volume flow rate with a flow meter and the cone angle of the liquid sheets issuing from the nozzle is obtained from series of photographs of the sheet for various liquid viscosity and injection pressure. And mean drop size is measured by image processing method. It is found that the geometrical characteristics of the nozzle and the variation of viscosity were the influential parameters to determine the spray characteristics such as the cone angle, discharge coefficients and SMD.

• 한국자동차공학회논문집
• /
• 제3권1호
• /
• pp.54-64
• /
• 1995

The effects of swirl on early flame development and late combustion characteristic were investigated using a high speed single-shot visualized 51 engine. LDV measurements were performed to get better understanding of the flow field in this combustion chamber. Spark plugs were located at half radius (R/2) and central location of bore. High speed schlieren photographs at 20,000 frames/sec were taken to visualize the detailed formation and development of the flame kernel with cylinder pressure measurements. This study showed that high swirl gave favorable effects on combustion-related performances in terms of the maximum cylinder pressure and flame growth rate regardless of spark position. However, at R/2 ignition the low swirl shown desirable effects at low engine speed gave worse performances as engine speed increased than without swirl. There were distinct signs of slow-down in flame growth during the period when the flame front expanded from 2.5mm in radius until it reached 5.0mm apparently due to the presence of ground electrode. There seemed to be heat transfer effect on the flame expansion speed which was evidenced in high swirl case by the slowdown of the late flame front presumably caused by relatively large heat loss from burned gas to wall compared with low- or no-swirl cases.

• Journal of Biosystems Engineering
• /
• 제31권3호
• /
• pp.153-160
• /
• 2006

This study was performed to evaluate some geometrical characteristics of disc type swirl nozzles and to develop nozzles having improved spraying performance for knapsack sprayers. Considered geometrical characteristics of the nozzles were disc thickness, orifice diameter, swirl chamber diameter and shape of the swirl chamber (nozzle chamber). 3 types of nozzle cores were compared. Main results of this study were as follows. 1. Spraying angle (A) was increased with decreasing disc thickness (x), and with increasing orifice diameter (y) or spraying pressure (z). The equation was as a follow. $$A=3.95\frac{1}{x}+73.50\sqrt{y}+18.97\sqrt{z}-60.16$$ 2. Spraying flow rate (F) was increased with decreasing disc thickness (x), and with increasing orifice diameter (y) or spraying pressure (z). The equation was as a follow. $$F=-89.95x+611.09y+620.49\sqrt{z}-868.20$$ 3. Mean spraying droplet size (V) was decreased with decreasing disc thickness (x), with increasing orifice diameter (y) in low spraying pressure, with decreasing orifice diameter (y) in high spraying pressure, and with increasing spraying pressure (z). $$V=148.77x^4-746.85x^3+1311.76x^2-917.31x$$ 4. The spray pattern was compared using CV values. The CV value of the nozzle core type 1 was 26.7% in spraying pressure $3\;kgf/cm^2$, the CV value of the core type 2 was 23.6% in spraying pressure $2\;kgf/cm^2$, the CV value of the core type 3 was 20.6% in spraying pressure $1\;kgf/cm^2$. 5. Minimum spraying pressure was improved from $1.5\;kgf/cm^2\;to\;1.0\;kgf/cm^2$ by changes of nozzle core shape.

• 한국추진공학회지
• /
• 제7권2호
• /
• pp.23-35
• /
• 2003

백홀은 스월 인젝터의 새로운 기하학적인 설계요소로서 스월 인젝터 내부에 있는 와류실의 연직 주입구후방에 위치하는 추가적인 빈 공간을 총칭한다. 이 백홀은 분무각이나 평균액적지름(SMD), 혼합 특성과 같은 스월 인젝터의 분무 특성을 변화시키게 된다. 이러한 백홀의 특성을 알아보기 위하여 직$.$간접 촬영 기법 및 PDPA와 기계적 유량 포집기 등을 사용하여 수류실험을 수행하였다. 백홀이 스월 인젝터 내에 존재하게 되면 단위시간당 유량이 증가하게 되어 분무되는 유동의 중심부가 강화된다. 또한 백홀은 스월 인젝터의 유동 분무각을 조절할 수 있게 하고 그로 인하여 혼합 효율을 변화시킨다.

• 한국추진공학회지
• /
• 제25권5호
• /
• pp.10-17
• /
• 2021

본 연구에서는 압력 선회형 인젝터를 이용한 모사 젤 추진제의 분무실험을 수행하여 젤화제 첨가량에 따른 분무특성을 파악하였다. 실험을 통해 인젝터 내부의 공기층이 노즐에 국부적으로 형성되며 점차 와류실까지 확장되는 것을 확인하였으며 뉴턴 유체의 공기층 발달과정과 형상학적으로 유사한 경향성을 보였다. 분무형상은 4개의 유형으로 구분하였으며, 이를 공기층의 형성과정과 연관하여 형상학적으로 분석하였다. 분무형상을 바탕으로 일반화된 레이놀즈수, 웨버수 및 오네소지수와 같은 무차원 수에 따라 분열영역을 구분하였다. 추후 분무성능에 영향을 미치는 와류실 형상변화에 따른 공기층의 형상과 안정성, 이에 따른 분무특성에 관한 연구가 추가로 필요할 것으로 사료된다.

• 한국군사과학기술학회지
• /
• 제6권4호
• /
• pp.113-123
• /
• 2003

Both numerical analysis and experiment of cold and hot tests were performed to obtain basic design data for the swirl coaxial type Injector and to predict the combustion performance. Mass distribution, mixing distribution, mixing efficiency, characteristic velocity efficiency were measured by the cold tests and numerical analysis using the commercial thermo-hydraulic program. Test and analysis variables were recess, pressure drop, velocity ratio, mixing spray, mixture ratio. Hot tests were performed for the Uni-element injector to compare the performance with the cold test results, and, hot tests for Multi-element injector were performed to compare the performance with Uni-element injector. Designed thrust of the Uni-element injector liquid rocket was 35kgf at sea level and combustion chamber pressure, 20bar. Kerosene and Lox were used as a propellant.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2002년도 학술대회지
• /
• pp.287-290
• /
• 2002

'Backhole' is an extra empty volume where is located behind the tangential entries at the rear par of the vortex chamber in the swirl coaxial injector. With the backhole, there are three major hydraulic characteristics. First, mass flow rate is increased about $15{\%}$ compared with the case without the backhole. Second, with the backhole, the center region of the injected flow has more large volume than that of without the backhole. The last, some range of the cone angle can be controlled by the backhole Experiments are conducted by using a PDPA apparatus, a mechanical patternator, stroboscopic photography and etc. With the backhole, based on cold-flow tests, the model swirl injector has some Improvement in its performance.