• 한국분무공학회지
• /
• 제22권4호
• /
• pp.159-168
• /
• 2017

Numerical studies on the spray characteristics of closed-type and open-type swirl injectors were conducted using ANSYS Fluent. By changing injection pressures, discharge coefficient and spray angle were calculated using the Reynolds stress BSL turbulent model. The numerical results were compared with previous experimental data to examine their accuracy. For a closed-type swirl injector, spray angles matched well with experimental results and discharge coefficients showed approximately 8% differences. On the contrary, discharge coefficients of an open-type swirl injector were similar with experimental result but its spray angles presented around 15% differences. Though the numerical results were not perfectly consistent with experimental data, it is thought that they could be sufficiently used for analyzing spray characteristics, specially which is hard to be measured from experiments. Numerical simulation with different turbulent models was also performed to examine their effects on the numerical results.

• 한국분무공학회지
• /
• 제23권2호
• /
• pp.49-57
• /
• 2018

Numerical study under single-injection on bi-swirl coaxial injectors with different recess lengths was performed using ANSYS Fluent. The bi-swirl coaxial injectors which consisted of inner closed-type and outer open-type swirl injectors, had three different recess lengths. By changing mass flow rates, numerical simulation was repeated using the Reynolds stress BSL turbulent model. The numerical results such as discharge coefficient and spray angle were compared with previous experimental data and were found to be approximately matched well with them, irrespective of recess length. Quantitative data which was hard to be measured from experiments, were successfully obtained through the present numerical study.

• 한국자동차공학회논문집
• /
• 제25권2호
• /
• pp.179-189
• /
• 2017

This paper is the fifth investigation on the methods of evaluating flow characteristics in a steady flow bench. In previous studies, several assumptions used in the steady flow bench were examined and it was concluded that the assumption of the solid rotation may lead to serious problems. In addition, though the velocity profiles were improved as the measuring position went downstream, the distributions were far from ideal regardless of the valve angle and evaluation position. The eccentricities were also not sufficiently small to disregard the effect on impulse swirl meter (ISM) measurement. Therefore, the effect of these distribution and eccentricity changes according to the positions needs to be analyzed to discuss the method of flow characteristics estimation. In this context, the effects of evaluation position on the steady flow characteristics were studied. For this purpose, the swirl coefficient and swirl ratio were assessed and compared via measurement of the conventional ISM and calculation based on the velocity by particle image velocimetry(PIV) from 1.75B, 1.75 times bore position apart from the cylinder head, to the 6.00B position. The results show that the swirl coefficients by ISM strictly decrease and the curves as a function of the valve lift become smooth and linear as the measuring position goes downstream. However, the values through the calculation based on the PIV are higher at the farther position due to the approach of the tangential velocity profile to ideal. In addition, there exists an offset effect between the velocity distribution and eccentricity in the low valve lift range when the coefficients are estimated based on the swirl center. Finally, the curve of the swirl ratio by ISM and by PIV evaluation as a function the measuring position intersect around 5.00B plane except at $26^{\circ}$ valve angle.

• 한국추진공학회지
• /
• 제17권5호
• /
• pp.70-79
• /
• 2013

마이크로 가스터빈용 하이브리드/이중 선회제트 연소기의 비반응 유동 및 혼합특성에 관한 수치해석 연구가 수행되었다. 고정된 열부하에서 pilot 버너의 위치, 선회 각 및 방향이 주요 변수로 검토되었다. 결과로서, pilot 버너의 위치, 선회 각 및 방향의 변화는 버너 출구 근처의 난류 유동장, 특히 중앙 재순환영역 및 난류강도의 큰 변화를 초래하며, 화염안정성 및 배기성능의 큰 변화를 동반하게 된다. 실험결과와의 비교를 통해, 하이브리드/이중 선회제트 연소기의 개발을 위하여 화염안정성 및 배기의 측면에서 pilot 버너의 최적 위치, 선회각$45^{\circ}$ 그리고 정방향 선회유동 조건들이 선택되었다.

• 대한기계학회논문집B
• /
• 제25권1호
• /
• pp.78-86
• /
• 2001

The Gasoline Direct Injection(GDI) system has been highlighted due to the improvement of fuel consumption and the control of exhaust emission from gasoline engines. The GDI system includes a high injection pressure, smaller mean diameter, good spray characteristics and stability. We were interested in the development for gasoline direct swirl injector(GDSI) in which the swirler is specially designed with an incident angle. Nymerical analysis was utilized to investigate the internal flow of GDSI with a goal to determine the swirl incident angle and needle lift. Accordingly, it describes characteristics of a GDSI in which the flowrate and spray characteristics are satisfied. especially the spray tip penetration decreases, compared with other type GDI, mean diameter of droplets is from 20${\mu}{\textrm}{m}$ to 25${\mu}{\textrm}{m}$ and spray angle ranges from 64$^{\circ}$to 66$^{\circ}$.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.16-17
• /
• 2006

In order to obtain spherical fine powder, we have developed a new method of high-pressure water atomization system using swirl water jet with the swirl angle $(\omega)$. The effect of nozzle apex angle $(\theta)$ upon the morphology of atomized powders was investigated. Molten copper was atomized by this method, with $\omega=0.2$ rad (swirl water jet) and $\omega=0$ rad (conical water jet). It was found that the median diameter $(D_{50})$ of atomized powders decreased with decreasing $(\theta)$ down to 0.35 rad in each $\omega$, but under ${\theta}<\;0.35$ rad, $D_{50}$ increased abruptly with decreasing $\theta$ for $\omega=0$ rad, while it was still decreased with decreasing $(\theta)$ for $\omega=0.2$ rad.

• Journal of Advanced Marine Engineering and Technology
• /
• 제38권10호
• /
• pp.1263-1268
• /
• 2014

In this study, the variations of swirl center according to evaluating position have been investigated in a steady flow bench of SI engine. For the experiments, two engine heads with different intake valve angles ($11^{\circ}$ and $26^{\circ}$) were tested in the flow bench by varying the evaluating position (1.75~6.0B) and valve lift (2~10 mm). Particle image velocimetry was used to measure the velocity field inside the engine cylinder. The swirl center position is found with a critical point theory and the intensity of turbulence is calculated from PIV velocity data. The results show that the center of swirl is located closer to the center of cylinder and turbulence intensity is lower, when the intake valve angle is the smaller. It is conventional to evaluate the swirl ratio at 1.75B position in the steady flow bench of SI engine. At this position, however, the distance of swirl center from the cylinder center scatters significantly for the variation of valve lift, and the turbulence intensity is much stronger regardless of the valve angle. Thus, to estimate the flow at the end of compression stroke in a real engine from the data in the steady flow experiments, the evaluation position should be moved further downstream more than 4.5B.

• 공업화학
• /
• 제19권3호
• /
• pp.295-298
• /
• 2008

ASTM D5757-95에 따른 입자 마모 측정기를 이용하여 접선 방향의 기체 주입에 따른 입자 마모 특성을 고찰하였다. 접선 방향의 기체 주입에 따른 영향을 고찰하기 위하여 모래의 입도 분포 변화, 비산 회재의 양 등을 측정하여 비교하였다. 입자 마모에 따라서 발생하는 미세 입자들은 기체 유속이 증가함에 따라서 증가하였다. 수직 방향의 기체 주입에 비해 접선 방향으로 기체를 주입함에 따라서 입자 마모량이 변하였으며 노즐의 각도가 감소함에 따라서 비산량이 줄어들었다. 또한 전체 유량이 동일한 경우, 사용되는 노즐이 증가할수록 입도변화가 커짐도 알 수 있었다.

• 한국분무공학회지
• /
• 제13권3호
• /
• pp.126-133
• /
• 2008

The atomization characteristics of the dual air supplying two-fluid nozzle were investigated experimentally using PIV and PDA systems. The twin-fluid nozzle is composed of three main parts: the feeding injector to supply fluid that is controlled by a PWM (pulse-width modulation) mode, the adaptor as a device with the ports for supplying the carrier and assist air, and the main nozzle to produce sprays. The main nozzle has the swirler with four equally spaced tangential slots, which gives the injecting fluid an angular momentum. The swirl angle in the swirler varied with $0^{\circ}$, $30^{\circ}$, $60^{\circ}$ and $90^{\circ}$. The ratios of carrier air to assist air and ALR (total air to liquid) were 0.55 and 1.23, respectively. The macroscopic behavior of the spray was investigated using PIV system, and the AMD and SMD distributions of the sprays were measured using PDA system. As a result, the SMD distribution increases along the radial distance, and it decreases with the increase of swirl angle in swirler.

• 한국추진공학회지
• /
• 제18권4호
• /
• pp.33-42
• /
• 2014

이중선회 연소기에서 다양한 화염거동과 파일럿 화염과 주 화염의 상호작용에 관한 연구가 수행되었다. 주 선회각이 $45^{\circ}$로 고정된 상태에서 파일럿 선회각도, 총 열 발생률 그리고 주 화염의 당량비가 주요 변수로 검토되었다. 주요한 결과로써, 이중선회 연소기의 상세한 화염안정화 영역이 총 발열량과 주화염의 당량비 변화를 통해 발생되는 5가지 화염모드를 통해 확인되었다. 파일럿 화염의 선회각도는 파일럿 화염의 위치 및 연소기 전체의 유동구조에 가장 큰 영향을 미치게 되며, 그 결과 내부 및 외부 화염간의 상호작용의 큰 변화를 가져온다.