• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.26 no.12
• /
• pp.1655-1662
• /
• 2002

Recently, many researches have been performed to improve the performance of the combustion and emission in a D.I.Diesel engine. And many new techniques have been introduced and developed to reduce NO$_{x}$ and soot exhausted from diesel combustion. Some of these methods have the peculiar injection timing which is not used to traditional timing. To optimize these injection timing, characteristics of swirl flow and interaction of swirl with injection in the diesel engine should be investigated more carefully. Therefore, in this study, 2-zone energy method is adopted for the understanding of swirl flow in condition of moving piston, and then flame visualizations and image process are performed. From these studies, the characteristics of the swirl flow generated by SCV was investigated and the effect of swirl on injection timing was elucidated. As the results, velocity distribution caused by swirl flow increase the space utilization rate of flame plums. And flame plums of weak momentum are remained inside of combustion chamber by the swirl flow.w.

• 한국연소학회:학술대회논문집
• /
• 2012.04a
• /
• pp.199-200
• /
• 2012

An experimental study on geometric optimization was conducted to develop a hybrid/dual swirl jet combustor for a micro-gas turbine. A hybrid concept indicating a combination of swirling jet partially premixed and premixed flames were adopted to achieve high flame stability as well as clean combustion. Location of pilot nozzle, angle and direction of swirl vane were varied as main parameters with a constant fuel flow rate for each nozzle. The results showed that the variation in location of pilot nozzle resulted in significant change in swirl intensity due to the change in flow area near burner exit, and thus, optimized nozzle location was determined on the basis of CO and NOx emissions under conditions of co-swirl flow and swirl $angle=30^{\circ}$. The increase in swirl angle (from $30^{\circ}$ to $45^{\circ}$) enhanced the emission performances, in particular, with a significant reduction of CO emission near lean-flammability limit. It was observed that the CO emission near lean-flammability limit was further reduced through the counter-swirl flow. However, there was not significant change in the NOx emission in the operating conditions (i.e. equivalence ratio of 0.6~0.7) between the co- and the counter-swirl flow.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.1
• /
• pp.92-99
• /
• 2006

The swirl ratio of a charge in the cylinder was estimated by calculating the ratio of the rotary speed of charge which could be simulated from the rotary speed of paddle in the swirl measurement apparatus, to the engine speed which could be calculated by measuring intake air flow rate. The automation of the swirl ratio measurement for cylinder head was achieved by controling both valve lift in cylinder head and a suction pressure of surge tank using two step-motors. The number of measurement position for calculating mean swirl ratio was varied by adjusting the interval of valve lift. The mean swirl ratio with varying the number of measurement position showed nearly constant value. Two measurement methods for measuring the swirl ratio were compared, one was to control the suction pressure of the surge tank with PID (proportional, integral, differential) mode with by-pass valve controlled by the step motor and the other did not control the surge tank pressure by fixing the by-pass valve. The difference of the mean swirl ratio between the two measurement methods showed nearly constant value with varying the number of measurement position. This means that the w/o PID control method could be preferred to the PID control method which has been used, due to the simpleness of the swirl measurement.

• Journal of ILASS-Korea
• /
• v.26 no.2
• /
• pp.81-87
• /
• 2021

This study was performed to calculate the swirl ratio of a diesel engine intake port by a 1D computer simulation under actual engine operating conditions. The swirl ratio of the intake port was simulated according to the change of the engine speed during the operation of the motoring without fuel injection. The swirl ratio of the intake port was simulated according to changes in the crank angle during the four-cycle operation of intake, compression, expansion and exhaust. The swirl ratio represented by the three regions of the piston, center and squish was simulated. Among the three regions, the piston-region swirl ratio is important for effective air-fuel mixing in the engine cylinder. In particular, it was confirmed during the simulation that the piston swirl ratio before and after the compression top dead center (TDC) point when fuel is injected in the DI diesel engine can have a significant effect on the mixing of air and fuel. It was desirable to set the average piston swirl ratio over a crank angle section before and after compression TDC as the representative swirl ratio of the cylinder head intake port according to the change of the engine speed.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.10
• /
• pp.1450-1456
• /
• 2003

Three-dimensional pipe flows with elbows, tees and headers in three different pipe systems are calculated to estimate the effect of asymmetry of axial velocity profile and swirl on measuring accuracy of an orifice flowmeter. It is evaluated how the pressure difference across the orifice is dependent on the upstream straight pipe length and how swirl intensity, swirl angle, and axial velocity distribution affect the measuring error of the orifice flowmeter. From the results, it is found that variation of the pressure difference across the orifice is negligible in case that maximum swirl angle is less than 2$^{\circ}$, and also that the pressure difference across the orifice is more sensitive to the asymmetry of axial velocity profile rather than the swirl intensity.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.3
• /
• pp.26-33
• /
• 1998

An experimental study has been conducted for the three-dimensional in-cylinder swirl flow under steady conditions. Velocity fields are measured by using an LDV at various valve lifts. Effects of geometry of inlet ports on swirl flows are investigated for standard and helical ports. Swirl distributions evaluated from velocity measurements are compared with those obtained from an impulse torque swirl meter. Results show that the helical port generates more intensive swirl than the standard one but it causes red- uction in air flow coefficient. At the lower valve lift, no significant difference is observ- ed in non-dimensional swirl values between two ports because of limited pre-swirl effect, while it becomes significant as the valve lift increases.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.7 no.4
• /
• pp.410-416
• /
• 1983

This study presents the combustion characteristics and flame structure of annular swirling flow when there were changes the equivalence ratio and swirl number of swirling jet of fuelair mixture. The conclusions of this study are as follows; During the investigations in which the change of equivalence ratio and swirl number were studied, three basic shapes of flame were observed in this study. Visible flame lengths of swirling jet results in the decrease with increasing of swirl number and air-fuel ratio of mixture. Radial distribution of flame temperature with strong swirl is higher than that of weak swirl at the same equivalence ratio of mixture. The angle of spread of the annular jet increases with the increase of swirl number. When the swirl intensity is increased in a jet, the decay of concentration of carbon dioxide is decreased with the distance from nozzle exit of burner.

• Journal of the Korean Ceramic Society
• /
• v.33 no.3
• /
• pp.321-326
• /
• 1996

Thermal fatigue test and stress analysis of Si3N4 and metal swirl chamber were carried out to investigate the reliability of the swirl chambers. Conditions of the thermal fatigue test were severer than those in real engine and FEM was used to analize the stress distribution in the swirl chambers. Fatigue cracks of the maximum length 2.4 mm and deformation were occurred at the corner of the jet in metal swirl chamber but not observed in Si3N4 swirl chamber. Maximum tensile stress in Si3N4 swirl chamber calculated by FEM was 300 MPa.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.6
• /
• pp.16-23
• /
• 2001

Spray dispersion in high pressure diesel engines have been simulated experimentally with a special emphasis on the effect of swirl by using a liquid injection technique. A constant volume chamber was designed to be rotatable in order to generate a continuous swirl and to have the flow field closely resembling a solid body rotation. Emulsified fuel was injected into the chamber and the developing process of fuel sprays was visualized. The effect of swirl on the spray dispersion was quantified by calculating non-dimensionalized dispersion area according to the spray tip penetration length. The results show that the effect of swirl on the spray dispersion is different between short and long spray penetrations. For short range of spray tip penetration, the effect of swirl on spray dispersion is quite small. However, as the spray tip is penetrated into longer distance in spray chamber, the effect of swirl on spray dispersion becomes larger. These results can be used as a basic data for designing combustion chamber and injection system of direct injection diesel engine.

• Journal of Advanced Marine Engineering and Technology
• /
• v.31 no.1
• /
• pp.26-33
• /
• 2007

The intake swirl motion, as one of dominant effects for an engine combustion. is very effective for turbulence enhancement during the compression process in the cylinder of 2-valve engine. Because the combustion flame speed is determined by the turbulence that is mainly generated from the mean flow of the charge air motion in intake port system. This paper describes the experimental results of swirl flow and combustion characteristics by using the oil spot method and back-scattering Laser Doppler velocimeter (LDV) in 2-valve single cylinder transparent LPG engine using the liquid phase LPG injection. For this. various intake port configurations were developed by using the flow box system and swirl ratios for different intake port configurations were determined by impulse swirl meter in a steady flow rig test. And the effects of intake swirl ratio on combustion characteristics in an LPG engine were analyzed with some analysis parameters that is swirl ratio. mean flow coefficient, swirl mean velocity fuel conversion efficiency. combustion duration and cyclic variations of indicated mean effective pressure(IMEP). As these research results, we found that the intake port configuration with swirl ratio of 2.0 that has a reasonable lean combustion stability is very suitable to an $11{\ell}$ heavy-duty LPG engine with liquid phase fuel injection system. It also has a better mean flow coefficient of 0.34 to develope a stable flame kernel and to produce high performance. This research expects to clarify major factor that effects on the design of intake port efficiently with the optimized swirl ratio for the heavy duty LPG engine.