• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.27 no.6
• /
• pp.382-390
• /
• 2015

To simulate a complicated hydrodynamic phenomena in the surf zone, the SWASH model is used in Haeundae Beach. The SWASH model is well known as a model competing with the Boussinesq-type model in terms of near shore waves and wave-induced currents modelling. This study is aimed to the detailed analysis of seasonal waves and wave-induced current simulation in Haeundae Beach, where the representative seasonal wave conditions was obtained from hourly measured wave data in 2014 by Korea Hydrographic and Oceanographic Administration( KHOA). Incident wave conditions were given as irregular waves by JONSWAP spectrum. The calculated seasonal wave-induced current patterns were compared with the field observation data. In summer season, a dominant longshore current toward the east of the beach appears due to the effect of incident waves from the South and the bottom bathymetry, then some rip currents occurs at the central part of the beach. In the winter season, ESE incident waves generates a strong westward longshore currents. However, a weak eastward longshore currents appears at the restricted east side areas of the beach.

• Proceedings of the SAREK Conference
• /
• 2004.06a
• /
• pp.139-139
• /
• 2004

• 한국전산유체공학회:학술대회논문집
• /
• 2008.03b
• /
• pp.156-158
• /
• 2008

Along the various gap distance between shoe and swash plate and pocket diameter, lifting force of piston shoe during the compressing stage was calculated. The flow in piston, orifice, shoe, and back space was considered to be 2-dimension axisymmetric and analysed by Fluent, a commercial CFD Software. The wall boundary condition was given as nonslip and adiabatic, while the change in fluid viscosity was considered as linear along temperature. Calculated lifting force and oil leakage of shoe was used in the design of a pump to confirm the shape of the shoe.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2001.11a
• /
• pp.186-193
• /
• 2001

In the high pressure state, the leakage flow rate of hydraulics is one of serious problems and the great reason to decrease the volume efficiency. In this paper, I tried to clarify tribology characteristics for the slipper hydrostatic bearing in swash plate type axial piston pumps and motors by means of experiment . I measured the leakage flow rate between swash plate and piston shoe with change the supply pressure and oil temperature at a swash plate angle of 0。 . And I also investigated the slipper pocket pressure and calculated oil film thickness for theoretical method. So. 1 have analyzed the tribology characteristics of hydrostatic bearing for leakage flow rate and oil film thickness with oil temperature and supply pressure.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.23 no.5
• /
• pp.313-320
• /
• 2011

For a steam Rankine cycle to recover waste heat from the exhaust gas of an Internal combustion engine, a swash plate type of expander as a power conversion unit has been designed. Numerical simulation has been carried out to estimate the performance of the designed expander. With the steam pressure and temperature of 35 bar and $300^{\circ}C$ at the expander inlet, respectively, the expander was estimated to produce the shaft power output of about 2.67 kW from the exhaust gas waste heat of 25.2 kW. The expander output increased almost linearly with the amount of exhaust gas waste heat in the range of from 5~40 kW, and the expander and Rankine cycle efficiencies showed gradual decreases in the ranges of 72.2%~69.5% and 10.8%~10.4%, respectively.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.10
• /
• pp.1989-1996
• /
• 2002

Extended Kalman Filter(EKF) is used to estimate friction and spring characteristics on the swash plate of a variable displacement pump. In earlier studies, the feasibility of the approach was established using simulation studies to establish limits of accuracy for the EKF approach when it was applied to an ideal situation. In this study, the EKF is applied to an experimental system and the issue of re liability in estimation of certain pump parameters is addressed. In addition, an approach to assign values to accommodate convergence of the EKF is considered. A special experimental system was set up to facilitate the measurement of certain states to enhance the EKF approach. Estimated parameters show ed some scatter about a specified operating point but in general, were reasonably repeatable. The study also showed that changes in the system parameters could be accurately tracked.

• Journal of Drive and Control
• /
• v.11 no.2
• /
• pp.30-35
• /
• 2014

The pumps of electro-hydrostatic actuators operate most frequently in boundary lubrication speed range, as they compensate for the position control errors as a control element. When conventional swash plate type piston pumps are applied to electro-hydrostatic actuators, the frictional power losses as well as the wear rate of sliding components, such as piston shoes can increase drastically under the boundary friction condition. In this paper, the power losses of the piston shoes were investigated which were engendered by a frictional solid-to-solid contact and leakage flow rate of their hydrostatic bearing. In order to reduce them, DLC-coating was applied to the swash plate and the ball joint of pistons along with its effects were demonstrated. In addition, it was also shown that the wear rate of the piston shoes could be markedly reduced using the DLC-coated swash plate.

• Journal of the Korean Society for Precision Engineering
• /
• v.8 no.2
• /
• pp.78-88
• /
• 1991

The existing axial piston pump/motors of swash plate type rapidly drop efficiency in high speed region in comparison with low speed. This is the reason why the pump/motors were designed only in a view point of power supply. But, in this paper, the motor which was optimally designed on power supply load capacitancy, flow loss volume, axial stiffness and tiliting stiffness keeps up high efficiency in high speed region and in high pressure resion too.

• Journal of Drive and Control
• /
• v.13 no.3
• /
• pp.86-90
• /
• 2016

• Bulletin of the Society of Naval Architects of Korea
• /
• v.53 no.4
• /
• pp.42-46
• /
• 2016