• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.11 no.1
• /
• pp.45-53
• /
• 2018

The proliferation of distributed power sources such as renewable energy sources drives the changes of consumers to prosumers who actively want to deal with energy. The prosumer is a new type of consumer that can sell surplus energy or additionally generated energy to electric power companies, other energy service providers, or other consumers. To implement such a concept, a new technology and platform that can support the transaction of the prosumers are required. However, the study in the area is limited since it is in the early stage. This work examines the state-of-the-art transaction-based energy management technology through comparative analysis of representative technologies to show the future trends. Although, technologies and standards for transaction based energy are not much matured yet. related new research will be continued via competitions.

• Journal of Mechanical Science and Technology
• /
• v.16 no.6
• /
• pp.839-850
• /
• 2002

A performance simulation program for the turboprop engine (PT6A-62), which is the power plant of the first Korean indigenous basic trainer KT-1, was developed for performance prediction, development of an EHMS (Engine Health Monitoring System) and the flight simulator. Characteristics of components including compressors, turbines, power turbines and the constant speed propeller were required for the steady state and transient performance analysis with on and off design point analysis. In most cases, these were substituted for what scaled from similar engine components'characteristics with the scaling law. The developed program was evaluated with the performance data provided by the engine manufacturer and with analysis results of GASTURB program, which is well known for the performance simulation of gas turbines. Performance parameters such as mass flow rate, compressor pressure ratio, fuel flow rate, specific fuel consumption and turbine inlet temperature were discussed to evaluate validity of the developed program at various cases. The first case was the sea level static standard condition and other cases were considered with various altitudes, flight velocities and part loads with the range between idle and 105% rotational speed of the gas generator. In the transient analysis, the Continuity of Mass Flow Method was utilized under the condition that mass stored between components is ignored and the flow compatibility is satisfied, and the Modified Euler Method was used for integration of the surplus torque. The transient performance analysis for various fuel schedules was performed. When the fuel step increase was considered, the overshoot of the turbine inlet temperature occurred. However, in case of ramp increase of the fuel longer than step increase of the fuel, the overshoot of the turbine inlet temperature was effectively reduced.

• Journal of the Korea Society of Computer and Information
• /
• v.13 no.4
• /
• pp.105-113
• /
• 2008

While the wireless sensor network has a strong point which does not have effect on whole activities of network even though neighboring sensor nods fail activities of some sensor nod or make some functions disappear by the characteristic of similar information detection, it has problems which is slowing down of wireless medium, transfer character with severe error, limited power supply, the impossibility of change by optional arrangement of sensor nods etc. This paper proposes PRML techniques which performs the fittest course searching process to reduce power consumption of entire nods while guarantees the scalability of network organizing sensor nods hierarchically. The proposed technique can scatter the load of cluster head by considering the connectivity with surplus energy of nod and reduce the frequency of communication among the nods. As a result of the analysis in comparison with LEACH-C and HEED technique, PRML technique get efficiency of average 6.4% in energy consuming respect of cluster head, efficiency of average 8% in entire energy consuming respect, and more efficiency of average 7.5% in other energy consuming distribution of network scalability than LEACH-C and HEED technique.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.15 no.2
• /
• pp.134-141
• /
• 2010

Small PEM (Proton Exchange Membrane) fuel cell systems do not require humidification and have great commercialization possibilities. However, methods for controlling small PEM fuel cell stacks have not been clearly established. In this paper, a control method for small PEM fuel cell systems using a dual closed loop with a static feedforward structure is defined and realized using a DSP (Digital Signal Processor). The fundamental elements that need to be controlled in fuel cell systems include the supply of air and hydrogen, water management inside the stack, and heat management of the stack. For small PEM fuel cell stacks operated without a separate humidifier, fans are essential for air supply, heat management, and water management of the stack. A purge valve discharges surplus water from the stack. The proposed method controls the fan using double control loops to quicken transient response of the fan thereby improving the supply rate of air. Feedback control to compensate for the voltage change in fuel cell stack improves the response characteristics in fuel cell to load variations. The feasibility of proposed method was proved by the experiments with a 60W small PEM fuel cell system and operation of a notebook computer using this system.

• Journal of Energy Engineering
• /
• v.25 no.4
• /
• pp.141-151
• /
• 2016

Recently, technology for energy recovery from waste has been increasing interest globally including the Korea. In Korea, we have interested in using biogas generated from the sewage treatment process. As one alternative, there are operating biogas combined heat and power plant. The generation amount of the Sewage Sludge are expected to grow in the future. For this reason, total processing cost of Sewage Sludge will increase. To solve this problem, it seems will be invested with the expansion of facilities that use biogas as energy. Therefore, quantitative information on such facilities is required. Thus, this study attempts to economic feasibility analysis for Seonam Biogas Combined Heat and Power Plant. Meanwhile, as the benefit items for economic feasibility analysis consider electricity supply benefit except for heat supply benefit. The average prices of electricity use were residence 123.69, commercial 130.46, and industry 102.59 won per kWh for the year 2015, In addition, the economic benefit are calculated to be residence 310.21, commercial 378.49, and industry 222.87 won per kWh. The results of economic feasibility analysis is NPV 72.18 billion won, B/C 1.90, IRR 37%, shows that economic validity of Seonam Biogas Combined Heat and Power Plant.

• Plant Journal
• /
• v.14 no.4
• /
• pp.39-47
• /
• 2018

In this research, when the output of the standard coal-fired thermal power plant operating continuously at the rated output of 500 MW is changed to operate at 300 to 500 MW, the amount of sulfur oxide produced and the amount of sulfur oxide in the absorption tower of desulfurization equipment and proposed an extra liquid to gas ratio improvement inversely proportional to the output. In order to calibrate the combustion efficiency at low power, the ratio of sulfur oxides relative to the amount of combustion gas is increased as the excess air ratio is increased. When the concentration of sulfur oxide at the inlet of the desulfurization absorber was changed from 300 to 500 ppm along with the output fluctuation. The liquid to gas ratio of limestone slurry and combustion gas was changed from 10.99 to 16.27. Therefore, if the concentration of sulfur oxides with output of 300 MW is x, The following correlation equation is recommended for the minimum required flow rate of slurry for the reduction of surplus energy due to the increase of the liquid weight at low load. $y1[m^3/sec]=0.11x+3.74$

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.11
• /
• pp.1757-1763
• /
• 2010

Flywheel energy storage system (FESS) is defined as a high speed rotating flywheel system that can save surplus electric power. The FESS is proposed as an efficient energy storage system because it can accumulate a large amount of energy when it is operated at a high rotating speed and no mechanical problems are encountered. The FESS consists of a shaft, flywheel, motor/generator, bearings, and case. It is difficult to simulate rotor dynamics using common structure simulation programs because these programs are based on the 3D model and complex input rotating conditions. Therefore, in this paper, a program for the FESS based on the 2D FEM was developed. The 2D FEM can model easier than 3D, and it can present the multi-layer rotor with different material each other. Stiffness changing of the shaft caused by shrink fitting of the hub can be inputted to get clear solving results. The results obtained using the program were compared with those obtained using the common programs to determine any errors.

• Journal of the Microelectronics and Packaging Society
• /
• v.28 no.2
• /
• pp.71-79
• /
• 2021

In this study, we have successfully fabricated the Sn-Ni paste and evaluated the bonding properties for high-temperature endurable EV (Electric Vehicle) power module applications. From evaluating of the micro-structural changes in the TLPS (Transient Liquid Phase Sintering) joints with Sn and Ni contents in the Sn-Ni pastes, a lack of Ni powders and Ni particle agglomerations by Ni surplus were observed in the Sn-20Ni and Sn-50Ni joints (in wt.%), respectively. In contrast, relatively dense microstructures are observed in the Sn-30Ni and Sn-40Ni TLPS joints. From differential scanning calorimetry (DSC) thermal analysis results of the fabricated Sn-Ni paste and TLPS bonded joints, we confirmed that the complete reactions of Sn with Ni to form Ni-Sn intermetallic compounds (IMCs) at bonding temperatures occurred, and there is no remaining Sn in the joints after TLPS bonding. In addition, the interfacial reactions and IMC phase changes of the Sn-30Ni joints under various bonding temperatures were reported, and their mechanical shear strength were investigated. The TLPS bonded joints were mainly composed of residual Ni particles and Ni₃Sn₄ intermetallic phase. The average shear strength tended to increase with increasing bonding temperature. Our results indicated a high shear strength value of approximately 30 MPa at a bonding temperature of 270 ℃ and a bonding time of 30 min.

• Journal of Biosystems Engineering
• /
• v.15 no.1
• /
• pp.52-60
• /
• 1990

The main purpose of this report is to analyse the utilization results of farm machinery, farm mechanization rate and influences on the farm household economy. These results are summarized as follows : 1) The annual working days of major farm machinery are from 34.3 to 68.8 days for power tillers and tractors ; 7.9 to 8.5 days for rice transplanters ; 3.6 to 6.9 days for binders ; and, from 18.6 to 20.6 days for combines. Also income and expenditures of the farm management reveals al surplus in major farm machinery except for binders. 2) The popularization rate of major farm machinery is currently low, reaching the level of the early 1970's in Japan and the level of the early 1980's in Taiwan for rice transplanters and harvesters respectively. 3) The farm mechanization rate is 81.7% in plowing & levelling, 66.3% in rice transplanting, 87.5% in pest and disease control, 62.1% in harvesting and 12.5% in drying. However the farm mechanization rate of rice transplanting, harvesting and drying still remains at a low level. 4) The composition rates of farm machinery and implements are 10.2% in farm management expenditures (23.6% in Japan) and 13.2% in fixed capitals (29.4% in Japan) which still reflect a low level, and below that of the 1970's in Japan. From these analysis results, farm mechanization contributes to the improvement of farm management. Nevertheless, the popularization status and mechanization rate are still at a low level in korea. Therefore, it is deemed desirable to furthure promote effective utilization methods and guide farmers in higher safety utilization and management technology.

• Journal of Biosystems Engineering
• /
• v.20 no.3
• /
• pp.275-287
• /
• 1995

The rice processing complex(RPC) consisted of the rice handling, drying, storage, and milling processes. It has been established at 83 locations domestically by April 1994, and 200 of RPC will be built more throughout the country. Therefore, this study has been performed to achieve two objectives as the followings : 1) Development of mathematical models which can assess the requirement of electricity, fuel, and labor for four model systems of rice processing complex. 2) Development of a computer simulation model which produce the improved designs of RPC by the evaluation results of energy requirements of four RPC models. The results from this study are summarized as follows : 1) Mathematical models were developed on the basis of result of mass balance analysis and required power of machines for each process. 2) A computer simulation model was developed, which can produce the improved designs of RPC by the evaluation results of energy requirements. The computer simulation model language was BORLAND $C^{++}$. 3) The results of simulation showed that total energy requirements were ranged from 75.94㎾h/t to 124.30㎾h/t. 4) From the results of computer analysis of energy requirement classified by drying type, it was found that energy requirement of the drying type A{paddy rice (PR) for storage-natural air drying(15%), PR for milling-heated air drying(16%)} were less than that of the drying type B{1 step-natural air drying(PR for storage : 18%, PR for milling : 20%), 2 step-heated air drying(PR for storage : 15%, PR for milling : 16%)}. 5) The energy efficient drying method is that all the incoming rough rice to RPC should be dried by national air drying systems. If it is more than the capacity of national air drying system, the amount of surplus rough rice is recommended to be dried by the heated air drying method.