• 한국해양공학회지
• /
• 제27권6호
• /
• pp.100-105
• /
• 2013

This paper presents a sea surface reconstruction method that uses measured radar images by applying filtering techniques and identifying wave characteristics of the surrounding the Ieodo ocean research station using WaveFinder (X-band wave measurement radar), which is installed in the station. In addition, the results obtained from real radar images are used to verify the reconstructed sea surface. WaveFinder is a marine system that was developed to measure wave information in real time. The WaveFinder installed in the station could acquire sequent images for the sea surface at constant time intervals to obtain real time information (Wave height, mean wave period, wave directionality, etc.) for the wave by getting a three-dimensional spectrum by applying an FFT algorithm to the acquired sequent images and wave dispersion relation. In particular, we found the wave height using the SNR (Signal to noise ratio) of the acquired images. The wave information measured by WaveFinder could be verified by comparing and analyzing the results measured using the wave measurement instrument (Sea level monitor) in the station. Additionally, the wave field around the station could be reconstructed through the three-dimensional spectrum and the inverse FFT filtering from the analyzed results for the measured radar images. We verified the applicability of the sea surface reconstruction method by comparing the measured and simulated sea surfaces.

• International Journal of Reliability and Applications
• /
• 제5권1호
• /
• pp.1-13
• /
• 2004

It is recently well recognized that the technique for the one-sided stress wave velocity measurement in structural materials provides measurement in structural materials provides valuable information on the state of the material such as quality, uniformity, location of cracked or damaged area. This technique is especially effective to measure velocities of longitudinal and Rayleigh waves when access to only one surface of structure is possible. However, one of problems for one-sided stress wave velocity measurement is to get consistent and reliable source for the generation of elastic wave. In this study, the laser based surface elastic wave was used to provide consistent and reliable source for the generation of elastic wave into the materials. The velocities of creeping wave and Rayleigh wave in materials were measured by the one-sided technique using laser based surface elastic wave. These wave velocities were compared with bulk wave velocities such as longitudinal wave and shear wave velocities to certify accuracy of measurement. In addition, the mechanical properties such as poisson's ratio and specific modulus(E/p) were calculated with the velocities of surface elastic waves.

• 한국철도학회논문집
• /
• 제7권4호
• /
• pp.391-399
• /
• 2004

This paper investigated the dispersion characteristics of horizontal surface waves as means to apply conversional SASW techniques. To verify this proposal, 3D finite element analysis and Transfer matrix solution were performed. SH wave(Love waves) has the some advantages in comparison with Rayleigh wave. Representatively, Love wave has a characteristics not affected by compression wave. These characteristics have the robust applicability for the surface wave investigation techniques. In this study, for the purpose of employing Love wave in the SASW method, the dispersion characteristics of the Love wave was extensively investigated by the theoretical and numerical approaches. The 3-D finite element and transfer matrix analyses for the half space and two-layer systems were performed to determine the phase velocities from Love wave as well as from both the vertical and the horizontal components of Rayleigh wave. Preliminary, numerical simulations and theoretical solutions indicated that the dispersion characteristics of horizontal surface wave(Love waves) can be sufficiently sensitive and appliable to SASW techniques.

• Ocean Systems Engineering
• /
• 제11권1호
• /
• pp.1-16
• /
• 2021

Experimental and numerical investigations were conducted to study the performance of a surface-fixed horizontal porous wave barrier in regular waves. The characteristics of the reflection and transmission coefficients, energy dissipation, and vertical wave force were examined versus different porosities of the barrier. Numerical simulations based on 3D Reynolds Averaged Navier-Stokes equations with standard low-Re k-ε turbulent closure and volume of fluid approach were accomplished and compared with the experimental results conducted in a 2D wave tank. Experimental measurements and numerical simulations were shown to be in satisfactory agreement. The qualitative wave behavior propagating over a horizontal porous barrier such as wave run-up, wave breaking, air entrapment, jet flow, and vortex generation was reproduced by CFD computation. Through the discrete harmonic decomposition of the vertical wave force on a wave barrier, the nonlinear characteristics were revealed quantitatively. It was concluded that the surface-fixed horizontal barrier is more effective in dissipating wave energy in the short wave period region and more energy conversion was observed from the first harmonic to higher harmonics with the increase of porosity. The present numerical approach will provide a predictive tool for an accurate and efficient design of the surface-fixed horizontal porous wave barrier.

• Journal of Welding and Joining
• /
• 제18권1호
• /
• pp.46-51
• /
• 2000

Ultrasonic nondestructive evaluation (UNDE) technique is commonly used for detecting inner defects in the materials. Recently, new methods are trying to apply for detecting surface and subsurface flaws using Rayleigh wave or creeping wave. These techniques, however, have following problems. Echo amplitude is remarkably affected by the surface conditions and discrimination of echo pattern is usually difficult because shear wave propagate in the material at the same time. We can apply surface SH-wave(which is horizontally polarized shear wave traveling along near surface layer) technique to detect surface flaws. In this paper, directivity, distance amplitude characteristics and detectability of surface flaws at fillet weld hills of the 5 MHz and 2 MHz surface flaws at fillet weld hills of the 5 MHz and 2 MHz surface Sh-wave are experimentally investigated. As a result of the study, it was found out that these techniques are valuable for the detection of fatigue cracks at fillet weld heels which can not be detected by other ultrasonic techniques such as angle beam technique and which are inaccessible for non-destructive testings e.g. MT(magnetic particle testing) or PT(liquid penetrant testing).

• International Journal of Concrete Structures and Materials
• /
• 제9권3호
• /
• pp.307-321
• /
• 2015

The primary objective of this study is to investigate the feasibility of an innovative surface-mount sensor, made of a piezoelectric disc (PZT sensor), as a consistent source for surface wave velocity and transmission measurements in concrete structures. To this end, one concrete slab with lateral dimensions of 1500 by 1500 mm and a thickness of 200 mm was prepared in the laboratory. The concrete slab had a notch-type, surface-breaking crack at its center, with depths increasing from 0 to 100 mm at stepwise intervals of 10 mm. A PZT sensor was attached to the concrete surface and used to generate incident surface waves for surface wave measurements. Two accelerometers were used to measure the surface waves. Signals generated by the PZT sensors show a broad bandwidth with a center frequency around 40 kHz, and very good signal consistency in the frequency range from 0 to 100 kHz. Furthermore, repeatability of the surface wave velocity and transmission measurements is significantly improved compared to that obtained using manual impact sources. In addition, the PZT sensors are demonstrated to be effective for monitoring an actual surface-breaking crack in a concrete beam specimen subjected to various external loadings (compressive and flexural loading with stepwise increases). The findings in this study demonstrate that the surface mount sensor has great potential as a consistent source for surface wave velocity and transmission measurements for automated health monitoring of concrete structures.

• 한국공작기계학회논문집
• /
• 제12권2호
• /
• pp.23-30
• /
• 2003

It is very important to detect and evaluate the surface or subsurface flaws because of their influences on mechanical properties of materials. Rayleigh wave and creeping wave are commonly used for the detection of surface and subsurface flaws. These techniques, however, have following problems. Each amplitudes are remarkably affected by the surface condition and evaluation of echo pattern is usually difficult because shear wave mode propagate in the material at the same time. On the other hand, surface SH-wave which is horizontally polarized shear wave traveling along near surface layer is an attractive technique for the surface or subsurface material characterization and this technique is useful to solve the problems mentioned above. In this paper, The stability and transmission coefficient of SH waves through a viscous fluid layer is theoretically studied and simulated. Its results agreed well with the theoretical expectation for the experimental verification. These experimental results show that viscosity of couplants, thickness of couplant and surface roughness are closely related to transfer efficiency in surface SH angle beam method.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 춘계학술대회논문집
• /
• pp.852-855
• /
• 2008

In this paper, we proposed a new type's PZT actuator using surface acoustic wave. This actuator uses Rayleigh wave as an operational traveling wave. For the development of the actuator, each components of surface acoustic wave motor like PZT substrate, slider and IDT was studied theoretically and fabricated. For the measurement of transfer function of PZT substrate and operation of surface acoustic wave motor, network analyzer and 13.56MHz RF generator were used. Also the model which expresses the driving characteristic best was suggested and simulation was executed for the suggested model. And the future research works for improvement of SAW actuator was suggested.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1997년도 봄 학술발표회 논문집
• /
• pp.537-543
• /
• 1997

A new procedure for the advanced one-side measurement of longitudinal wave and surface wave velocities in concrete is presented in this paper. Stress waves are generated in a consistent fashion with a DC solenoid. Two piezoelectric accelerometers are mounted on the surface of a specimen as receivers. Stress waves propagate along the surface of the specimen and are detected by the receivers. In order to reduce the large incoherent noise levels of the signals, signals are collected and manipulated by a computer program for each velocity measurement. For a known distance between the two receivers and using the measured flight times, the velocities of the longitudinal wave and the surface wave are measured. The velocities of the longitudinal wave determined by this method are compared with those measured by conventional methods on concrete, PMMA and steel.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2009년도 세계 도시지반공학 심포지엄
• /
• pp.209-218
• /
• 2009

In this study, properties of shear wave velocity of core zone in filldams are analyzed. Shear wave velocity is derived using analysis of surface wave method that can be used nondestructively on the surface of filldams. These values are acquired through the tests for the core zone of six filldams by SASW and HWAW methods. Existing 2 more results are added. Shear wave velocity according to the depth and confining pressure are estimated, respectively. These analytical results are compared with the frequently used empirical method by Sawada and Takahashi.