• Korean Chemical Engineering Research
• /
• v.43 no.2
• /
• pp.206-214
• /
• 2005

Heterogeneously-catalyzed oxidation of aqueous phase trichloroethylene (TCE) over supported metal oxides has been conducted to establish an approach to eliminate ppm levels of organic compounds in water. A continuous flow reactor system was designed to effect predominant reaction parameters in determining catalytic activity of the catalysts for wet TCE decomposition as a model reaction. 5 wt.% $CoO_x/TiO_2$ catalyst exhibited a transient period in activity vs. on-stream time behavior, suggesting that the surface structure of the $CoO_x$ might be altered with on-stream hours; regardless, it is probable to be the most promising catalyst. Not only could the bare support be inactive for the wet decomposition reaction at $36^{\circ}C$, but no TCE removal also occurred by the process of adsorption on $TiO_2$ surface. The catalytic activity was independent of all particle sizes used, thereby representing no mass transfer limitation in intraparticle diffusion. Very low TCE conversion appeared for $TiO_2$-supported $NiO_x$ and $CrO_x$ catalysts. Wet oxidation performance of supported Cu and Fe catalysts, obtained through an incipient wetness and ion exchange technique, was dependent primarily on the kinds of the metal oxides, in addition to the acidic solid supports and the preparation routes. 5 wt.% $FeO_x/TiO_2$ catalyst gave no activity in the oxidation reaction at $36^{\circ}C$, while 1.2 wt.% Fe-MFI was active for the wet decomposition depending on time on-stream. The noticeable difference in activity of the both catalysts suggests that the Fe oxidation states involved to catalytic redox cycle during the course of reaction play a significant role in catalyzing the wet decomposition as well as in maintaining the time on-stream activity. Based on the results of different $CoO_x$ loadings and reaction temperatures for the decomposition reaction at $36^{\circ}C$ with $CoO_x/TiO_2$, the catalyst possessed an optimal $CoO_x$ amount at which higher reaction temperatures facilitated the catalytic TCE conversion. Small amounts of the active ingredient could be dissolved by acidic leaching but such a process gave no appreciable activity loss of the $CoO_x$ catalyst.

• Clean Technology
• /
• v.18 no.1
• /
• pp.102-110
• /
• 2012

In this study, the production of bio-diesel from animal oil by esterification and trans-esterification was investigated. There were three different extraction methods for oil extraction from raw animal fat. Heterogeneous catalysts such as Amberlyst-15 and Amberlyst BD-20 and a homogeneous catalyst such as sulfuric acid were used for esterification. Among three catalysts, the removal efficiency of Free Fatty Acid (FFA) was the highest in sulfuric acid. Response surface method was carried out to find the optimal esterification condition of sulfuric acid and methanol. After the esterification under the optimal condition, this animal fat was used for the trans-esterification. Animal oil used for trans-esterification was below 1% of FFA content and 0.09% of water content. The catalysts for trans-esterification were KOH, NaOH and $NaOCH_3$. To investigate the effects of catalyst type and amount on trans-esterification, The amount of catalyst were changed with 0.3, 0.6 and 0.9 wt%. The molar ratio of methanol/oil was changed with 4, 6, 9 and 12. The amount of catalyst was fixed to 0.8 wt%. The KOH catalyst showed the highest FAME conversion for trans- esterification, and the optimal methanol/oil weight ratio was 6. In the experiments of various catalysts and methanol molar ratios, the highest content of FAME is 96%. However, this FAME content was below Korean bio-diesel standard which is 96.5% of FAME content. After distillation, FAME content increased to 98%.

• Korean Journal of Environment and Ecology
• /
• v.24 no.6
• /
• pp.751-762
• /
• 2010

In order to understand the influence that the plant cover condition of the high-rise building outer space causes to the temperature change, we selected 12 high-rise building constructed in Seoul City. The land cover type of the outside was classified into six type(outer road, paved surface, shrub/grassland, single-layer tree planting-site, multi-layer planting-site, and waterscape facilities) and the temperature was measured at the representative point for each type in order to analyze the land cover temperature differential for each type of the high-rise building outer space. The study area showing the temperature tendency to be similar based upon one way analysis of variance after selecting the central part of the outer road for a control and measuring a temperature in order to consider the neighboring environmental difference of the dozen building was classified into 4 groups. As to the one-way layout result of variance analysis with the land cover type of the classified group and outer space temperature, the single-layer tree planting-site, waterscape facilities, and multi-layer planting-site belonged mainly to the low temperature section. The shrub/grassland, paved surface, and outer road belonged to the high temperature region. The temperature difference between low temperature region and high temperature region is about $1.06{\sim}6.17^{\circ}C$. However, the temperature in the Outer Space of the Super-High-Rise Building was variously appeared by the influence such as the cramped of the created planting-site and waterscape facilities area, the increase of amount of solar radiation and the reduction of reflection amount of light due to building etc.. Thus, the composition all produced the area of the green quantity required for each space and water space in advance. It was determined that there were the minimum area displaying an effect and the necessity to it secures the green quantity.

• Food Science and Preservation
• /
• v.15 no.1
• /
• pp.58-65
• /
• 2008

The Acorn (Quercus acutissima CARRUTHERS), which contains a large quantity of tannin, should be developed as a processed food as the acorn is rich in natural antioxidants and other valuable components. Accordingly, acorn extraction conditions for polyphenol and gallic acid (both antioxidants) were investigated by response surface methodology. The content of polyphenols were determined under 16 different extraction conditions based upon a central composite design. The parameters varied over $30-70^{\circ}C$ of extraction temperature, 1-5 h of extraction time, and 5-25 mL/g of solvent ratio, Gallic acid extraction was optimal at $60-100^{\circ}C$ extraction temperature, 1-5 h of extraction time, and 5-25 mL/g of solvent ratio, Epicatechin content was highest at $56.77^{\circ}C$, 4.16 hand 22.38 mL/g. Catechin content was highest at $52.37^{\circ}C$, 2h and 23.59 mL/g. The maximum catechin content was $91.30{\mu}g/mL$. Epigallocatechin content was influenced by extraction temperature and time. The maximum epigallocatechin content was $1,066.56{\mu}g/mL$ at $61.42^{\circ}C$, 4.17h, and 9.25 mL/g. The maximum value of epicatechingallate content was $125.39{\mu}g/mL$ at $47.72^{\circ}C$, 3.04h, and 24.93mL/g. Epigallocatechingallate content was influenced principally by solvent ratio and the maximum content was $61.38{\mu}g/mL$ at $48.11^{\circ}C$, 2.96h, and 24.95mL/g. The total polyphenol content was maximal at $1,332.75{\mu}g/mL$, after extraction at $61.50^{\circ}C$, 4.24h, at 9.71mL/g. The higher the extraction temperature and the longer the extraction time, the greater the polyphenol content. Gallic acid content was highest, the maximal level was $30.51{\mu}g/mL$ after $65.84^{\circ}C$, 1.65h at 17.17 mL/g, and this was influenced principally by extraction time and solvent ratio.

• Food Science and Preservation
• /
• v.24 no.1
• /
• pp.13-20
• /
• 2017

This study was carried out to investigate the quality characteristics of fried fish paste prepared with different amounts of squeezed Aronia melanocarpa juice. Squeezed Aronia melanocarpa juice (AMJ) was incorporated into fish paste at different levels (containing 2, 7, and 12 g of Aronia melanocarpa juice in 2 AMJ, 7 AMJ, and 12 AMJ, respectively) based on the total weight of water. Sugar contents and total acidity increased with increasing AMJ content. With increasing amounts of AMJ in fried fish paste, L value inside and on the surface decreased, a value increased, and b value inside decreased, whereas b value on the surface increased. pH decreased with increasing levels of AMJ. As the result of textural properties, folding test in all samples showed that AA means good flexibility. The strength, hardness, and chewiness of fried fish paste with AMJ increased while cohesiveness was not significantly different. Total polyphenol contents increased with higher levels of AMJ. DPPH radical scavenging activity was significantly higher than those of the control. In the sensory evaluation, fried fish paste containing 7 AMJ received the highest score than both the control and other samples.

• Restorative Dentistry and Endodontics
• /
• v.32 no.3
• /
• pp.222-235
• /
• 2007

The objectives of this study was to evaluate the effect of thermocycling on the ${\mu}TBS$ (microtensile bond strength) to dentin with four different adhesive systems to examine the bonding durability. Freshly extracted $3^{rd}$ molar teeth were exposed occlusal dentin surfaces, and randomly distributed into 8 adhesive groups 3-steps total-etching (Scotchbond Multi-Purpose Plus; SM, All Bond-2; AB), 2-steps total-etching (Single Bond; SB, One Step plus; OS), 2-steps self-etching (Clearfil SE Bond; SE, AdheSE AD) and single-step self-etching systems (Promp L-Pop; PL, Xeno III; XE) Each adhesive system in 8 adhesives groups was applied on prepared dentin surface as an instruction and resin composite (Z250) was placed incrementally and light-cured. The bonded specimens were sectioned with low-speed diamond saw to obtain $1\times1mm$ sticks after 24 hours of storage at $37^{\circ}C$ distilled water and proceeded thermocycling at the pre-determined cycles of 0, 1,000 and 2,000. The ${\mu}TBS$ test was carried out with EZ-tester at 1mm/min. The results of bond strength test were statistically analyzed using one-way ANOVA/ Duncan's test at the a < 0.05 confidence level. Also, the fracture mode of debonded surface and the interface were examined under SEM. The results of this study were as follows ; 1. 3-step total etching adhesives showed stable, but bond strength of 2-step adhesives were decreased as thermocycling stress. 2. SE showed the highest bond strength, but single step adhesives (PL, XE) had the lowest value both before and after thermocycling. 3 Most of adhesives showed adhesive failure. The total-etching systems were prone to adhesive failure and the single-step systems were mixed failure after thermocycling. Within limited results of this study, the bond strength of adhesive system was material specific and the bonding durability was affected by the bonding step/ procedure of adhesive Simplified bonding procedures do not necessarily imply improved bonding performance.

• Radiation Oncology Journal
• /
• v.13 no.3
• /
• pp.277-283
• /
• 1995

Purpose : This study was performed to measure dose alteration at the air-tissue interface resulting from rebuild-up to the loss of charged particle equilibrium in the tissues around the air-tissue interfaces. Materials and Methods : The 6 and 10-MV photon beam in dual energy linear accelerator were used to measure the surface dose at the air-tissue interface The polystyrene phantom sized $25{\times}25{\times}5\;cm^3$ and a water phantom sized $29{\times}29{\times}48\;cm^3$ which incorporates a parallel-plate ionization chamber in the distal side of air gap were used in this study. The treatment field sizes were $5{\times}5\;cm^2,\;10{\times}10\;cm^2\;and\;20{\times}20\;cm^2$. Air cavity thickness was variable from 10 mm to 50 mm. The observed-expected ratio (OER) was defined as the ratio of dose measured at the distal junction that is air-tissue interface to the dose measured at the same point in a homogeneous phantom. Results : In this experiment, the result of OER was close or slightly over than 1.0 for the large field size but much less (about 0.565) than 1.0 for the small field size in both photon energy. The factors to affect the dose distribution at the air-tissue interface were the field size, the thickness of air cavity. and the photon energy. Conclusion : Thus, the radiation oncologist should take into account dose reduction at the air-tissue interface when planning the head and neck cancer especially pharynx and laryngeal lesions, because the dose can be less nearly $29{\%}$ than predicted value.

• Journal of Physiology & Pathology in Korean Medicine
• /
• v.20 no.1
• /
• pp.163-170
• /
• 2006

Nardostachyos Rhizoma (N. Rhizoma) belonging to the family Valerianaceae has been anti-arrhythmic effect, and sedation to the central nerve and a smooth muscle. We reported that the water extract of N. Rhizoma induced apoptotic cell death and differentiation in human promyelocytic leukemia (HL-60) cells. Cytotoxicity of N. Rhizoma was detected only in HL-60 cells (IC50 is about 200 ${\mu}g/ml$). The cytotoxic activity of N. Rhizoma in HL-60 cells was increased in a dose-dependent manner. We used several measures of apoptosis to determine whether these processes were involved in N. Rhizoma-induced apoptotic cell death. The high-dose (200 ${\mu}g/ml$) treatment of N. Rhizoma to HL-60 cells showed cell shrinkage, cell membrane blobbing, apoptotic bodies, and the fragmentation of DNA, suggesting that these cells underwent apoptosis. Treatment of HL-60 cells with N. Rhizoma time-dependently induced activation of caspase-3, caspase-8, and caspase-9 and proteolytic cleavage of poly(ADP-ribose) polymerase. Also, we investigated the effect of N. Rhizoma on cellular differentiation and proliferation in HL-60 cells. Differentiation and proliferation of HL-60 cells was determined through expression of CD11b and CD14 surface antigens using flow cytometry and nitroblue tetrazolium (NBT) assay, and through analysis of cell cycle using propidium iodide assay, respectively. N. Rhizoma induced the differentiation of HL-60 at the low-dose (100 ${\mu}g/ml$) treatment, as shown by increased expression of differentiation surface antigen CD11b, but not CDl4 and increased reducing activity of NBT. When HL-60 cells were treated with N. Rhizoma at concentration of $50{\mu}g/ml\;and\;100{\mu}g/ml$, NBT-reducing activities induced approximately 1.5-fold and 20.0-fold as compared with the control. In contrast, HL-60 cells treated with the N. Rhizoma-ATRA combination showed markedly elevated levels of 26.3-fold at $50{\mu}g/ml$ N. Rhizoma-0.1 ${\mu}M$ ATRA combination and 27.5-fold at 50 ${\mu}g/ml$ N. Rhizoma-0.2 ${\mu}M$ ATRA combination than when treated with N. Rhizoma alone or ATRA alone. It may be that N. Rhizoma plays important roles in synergy with ATRA during differentiation of HL-60 cells. DNA flow-cytometry indicated that N. Rhizoma markedly induced a G1 phase arrest of HL-60 cells. N. Rhizoma-treated HL-60 cells increased the cell population in G1 phase from 32.71% to 42.26%, whereas cell population in G2/M and S phases decreased from 23.61% to 10.33% and from 37.78% to 33.98%, respectively. We examined the change in the $p21^{WAF1/Cip1}\;and\;p27^{Kip1}$ proteins, which are the CKIs related with the G1 phase arrest. The expression of the CDK inhibitor $p27^{Kip1},\;but\;not\;p21^{WAF1/Cip1}$ were markedly increased by N. Rhizoma. Taken together, these results demonstrated that N. Rhizoma induces apoptotic cell death through activation of caspase-3, and potently inhibits the proliferation of HL-60 cells via the G1 phase cell cycle arrest in association with $p27^{Kip1}$ and granulocytic differentiation induction .

• Korean Journal of Environmental Biology
• /
• v.35 no.4
• /
• pp.492-500
• /
• 2017

The purpose of this study was to investigate the seasonal distribution of phytoplankton as prey for oysters and to characterize the environmental factors controlling their abundance from June 2016 to May 2017, in the northeast coast between Tongyeong and Saryang Island, particularly for the oyster farming area. During the survey period, water temperature changed from $7.54^{\circ}C$ in February to $29.5^{\circ}C$ in August. The abnormal high temperature persisted during one month in August. Salinity was low due to summer rainfall and typhoon. The lowest level was 30.68 psu in September, and it peaked at 34.24 psu in May. The dissolved oxygen (DO) concentration ranged from $6.0-9.45mg\;L^{-1}$, and the DO concentration in the surface layer was like that in the bottom layers. The seasonal trends of pH were also like those of DO. The pH ranged from 7.91 to 8.50. Nitrate with nitrite, phosphate, and silicate concentrations ranged from $0.14{\mu}M$ to $7.66{\mu}M$, from $0.01{\mu}M$ to $4.16{\mu}M$, and from $0.27{\mu}M$ to $20.33{\mu}M$, respectively. The concentration of chlorophyll a (Chl. a) ranged from $0.37{\mu}g\;L^{-1}$ to $2.44{\mu}g\;L^{-1}$ in the surface layer. The annual average concentration was $1.26{\mu}g\;L^{-1}$. The annual mean phytoplankton community comprised Bacillariophyta (69%), Dinophyta (17%), and Cryptophyta (10%), respectively. Dinoflagellate Prorocentrum donghaiense in June was the most dominant at 90%. In the summer, diatom Chaetoceros decipiens, Rhizosolenia setigera and Pseudo-nitzschia delicatissima were dominant. These species shifted to diatom Chaetoceros spp. and Crytophyta species in autumn. In the winter, high densities of Skeletonema spp. and Eucampia zodiacus were maintained. Therefore, the researchers thought that the annual mean Chl. a concentration was relatively lower to sustain oyster feeding, implying that the prey organism (i.e., phytoplankton) was greatly controlled by continuous filter feeding behavior of oyster in the vicinity area of the oyster culture farm.

• Korean Journal of Remote Sensing
• /
• v.25 no.4
• /
• pp.339-357
• /
• 2009

The Saemangeum Reclamation Project was launched as a national project in 1991 to reclaim a large coastal area of 401 km$^2$ by constructing a 33-km long dyke. The final dyke enclosure in April 2006 has transformed the tidal flat into lake and land. The dyke construction has abruptly changed not only the estuarine tidal system inside the dyke, but also the coastal marine environment outside the dyke. In this study, we investigated the spatial change of SST distribution using the Landsat-5/7 and NOAA data before and after the dyke completion in the Saemangeum area. Satellite-induced SST was verified by compared with the various in situ measurements such as tower, buoy, and water sample. The correlation coefficient resulted in above 0.96 and RMSE was about 1$^{\circ}C$ in all data. 38 Landsat satellite images from 1985 to 2007 were analyzed to estimate the temporal and spatial change of SST distribution from the beginning to the completion of the Samangeum dyke's construction. The seasonal change in detailed spatial distribution of SST was measured, however, the estimation of change during the Saemangeum dyke's construction was hard to figure out owing to the various environmental conditions. Monthly averaged SST induced from NOAA data from 1998 to 2007 has been analyzed for a complement of Landsat's temporal resolution. At the inside of the dyke, the change of SST from summer to winter was large due to the relatively high temperature in summer. In this study, multi-sensor thermal remote sensing is an efficient tool for monitoring the temporal and spatial distribution of SST in coastal area.