• 한국염색가공학회지
• /
• 제25권1호
• /
• pp.25-29
• /
• 2013

Poly ketone (PK) was photo-oxidized by UV/ozone irradiation and the effect of UV energy on the surface properties of the UV-irradiated PK film was investigated by the measurement of reflectance, surface roughness, contact angles, ESCA, and ATR. Reflectance, particularly at the wavelength of 380nm, decreased with increasing UV energy. And the irradiation produced nano-scale roughness on the surface uniformly. The maximum surface roughness increased from 25.3nm for the unirradiated sample to 104.9nm at the irradiation of $42.4J/cm^2$. The improvement in hydrophilicity was caused by the introduction of polar groups such as C-O and C=O bonds resulting in higher $O_{1s}/C_{1s}$. The surface energy of PK film increased from $43.3mJ/m^2$ for the unirradiated sample to $71.9mJ/m^2$ at the irradiation of $31.8J/cm^2$. The zeta potential of the UV-irradiated PK decreased with increased UV energy and the dyeability to cationic dyes increased accordingly, resulting from the photochemically introduced anionic and dipolar dyeing sites on the PK films surfaces.

• 대한기계학회논문집
• /
• 제11권3호
• /
• pp.488-500
• /
• 1987

본 연구에서는 축대칭 봉재의 원주상에 기계가공된 인공릿지가 공구를 통하여 진행할 때의 변형모델을 제시하고 이를 상계해법으로 해석하여 표면소성 연마가공이 되기 위한 릿지의 물결모양운동과 이 운동이 일어나지 못하고 릿지가 편평해지면서 소 멸되고 또는 전단이 되는 경우들에 대한 판정조건 및 한계영역을 설정하였다. 순동 및 연강 그리고 알루미늄등을 시험재료로하여 이론적으로 예측된 릿지의 세 가지 운동 에 대해 실험을 통하여 검증하였으며 물결모양운동으로 인한 가공물의 표면조도 개선 정도를 시험전후에 최대높이 표면조도의 크기로 측정하여 비교하였다. 또한 릿지의 물결모양운동으로 인하여 가공물의 표층부에 형성된 가공변질층의 깊이를 이론적으로 예측하여 실험과 비교하였다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2006년도 춘계 학술발표회 논문집
• /
• pp.494-505
• /
• 2006

In this study, using constant normal stiffness(CNS) direct shear tests, side shear load distribution were analyzed by the influencing parameters of unconfined compressive strength, surface roughness, confining stress, and material properties. Based on the CNS tests, side shear load transfer function of drilled shafts in rock is proposed using geological strength index(GSI), which indicates discontinuity and surface condition of rock mass in Hoek-Brown criterion. Though comparisons with results of nine drilled shafts's load tests, it is found that the load-transfer curve by this study is in good agreement with the general trend observed by in situ measurements, and thus represents a significant improvement in the prediction of bearing capacity of drilled shaft.

• 설비공학논문집
• /
• 제14권8호
• /
• pp.641-647
• /
• 2002

Objectives of this paper are to investigate the effect of roughness of micro-hatching tubes on the absorption performance and to develop on experimental correlation of Nusselt as a function of the roughness. Three different micro-scale hatched tubes and a bare tube were tested in the present experiment. $H_{2}O/LiBr$ solution is used as working fluid. It was found that absorption performance of micro-scale hatched tubes were improved upto 2 times with an error band of ${\pm}25%$ compared with the bare tube. An experimental correlation of Nusselt was developed as a function of the roughness.

• 대한기계학회논문집A
• /
• 제38권9호
• /
• pp.1013-1018
• /
• 2014

자기연마가공은 연마입자와 자성입자를 혼합한 공구의 유연성을 이용하여, 공작물 표면을 폴리싱하는 특수가공법이다. 기존 연구의 대부분은 가공 정밀도를 향상시키기 위해서 연마입자의 크기를 달리 하는 것에 관한 내용들이다. 그러나 자기연마 가공에서는 연마입자의 크기뿐만 아니라, 자성입자의 크기도 가공에 많은 영향을 미칠 것으로 판단되며 이에 대한 연구가 반드시 필요하다. 따라서 본 연구에서는 크기가 다른 자성입자들을 사용하여 자기연마가공의 효과를 평가하였다. 자성입자는 철분말을 사용하였으며, 직경이 평균 8, 78, $250{\mu}m$의 크기이다. 공작물의 표면거칠기 향상 정도를 비교하여 자성입자의 크기가 자기연마가공의 정밀도에 미치는 효과를 평가하였다. 자성입자의 크기는 표면거칠기의 향상에 많은 영향을 미치며, 직경이 $78{\mu}m$일 때 가장 좋은 표면거칠기의 향상을 나타내었다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 C
• /
• pp.1349-1351
• /
• 2001

Polycrystalline diamond films are deposited by using a microwave plama CVC system, where the bias-enhanced nucleation (BEN) method is employed. Effects of the varying microwave power, the surface treatment by hydrogen plasma, and the cyclic hydrogen etching during deposition on the crystallinity as well as on the surface roughness of deposited films are examined by Raman spectroscopy, SEM, and AFM. A novel method for achieving a smoother diamond surface is also suggested through the indirect wafer bonding and back-side polishing.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 추계학술대회 논문집 전기물성,응용부문
• /
• pp.142-144
• /
• 2005

Main purpose of this study is a improved efficiency of Organic light emitting diodes(OLEDs) concerning $UV/O_3$ treatment. We investigated the efficiency of OLEDs by $UV/O_3$ treatment of ITO surface. We measured current density-voltage, luminance-voltage characteristics in different $UV/O_3$ treatment time and observed ITO surface roughness by using AFM(Atomic Force Microscope). The fundamental structure of the OLEDs was $ITO/NPB/Alq_3/LiF/Al$. We performed $UV/O_3$ treatment and found that $UV/O_3$ treatment enhanced the performance of OLEDs. We also found that change of surface roughness according to difference time a $UV/O_3$ treatment

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1999년도 춘계학술대회 논문집
• /
• pp.256-262
• /
• 1999

By development of heat resistant alloy, there are much improvement of gas turbine engines. But heat resistant alloy has difficulty of machining. therefore, ECM (Electrochemical Machining) is used for Machining of 3 dimensional curved surface of Ni-base alloy. The purpose of this paper is to investigate ECM parameters that make tile good surface for Ni-base alloy blade. For this purpose, we have been investigated that center line average surface roughness(R$\sub$a/), average R$\sub$a/, Maximum R$\sub$a/ and Standard deviation of R$\sub$a/ for measuring positions is influenced on ECM parameters such as electrolyte types, dwell time, electrolyte pressure and sort of electrolyte for Inconel 718 and Waspaloy.

• Advances in materials Research
• /
• 제1권2호
• /
• pp.129-146
• /
• 2012

Polycrystalline diamond is an ideal material for parts with micro-holes and has been widely used as dies and cutting tools in automotive, aerospace and woodworking industries due to its superior wear and corrosion resistance. In this research paper, the modeling and simultaneous optimization of multiple performance characteristics such as material removal rate and surface roughness of polycrystalline diamond (PCD) with ultrasonic machining process has been presented. The fuzzy logic and taguchi's quality loss function has been used. In recent years, fuzzy logic has been used in manufacturing engineering for modeling and monitoring. Also the effect of controllable machining parameters like type of abrasive slurry, their size and concentration, nature of tool material and the power rating of the machine has been determined by applying the single objective and multi-objective optimization techniques. The analysis of results has been done using the MATLAB 7.5 software and results obtained are validated by conducting the confirmation experiments. The results show the considerable improvement in S/N ratio as compared to initial cutting conditions. The surface roughness of machined surface has been measured by using the Perthometer (M4Pi, Mahr Germany).

• Design & Manufacturing
• /
• 제13권3호
• /
• pp.48-52
• /
• 2019

As the consumer market in the mold, automation and aerospace industries grows, the demand for chemical machining using on electrochemical polishing increases. To enhance the surface roughness and gloss of the micro-needle, we have studied for an electrochemical polishing. Electrochemical polishing requires the chemical reaction of solution and material according to the electrolyte and electrode. In this study, sulfuric acid(30%), phosphoric acid(50%), and DI-water(20%)were used as the electrolytic solution, and the electrolytic solution temperature used $58^{\circ}C$. Electrochemical polishing was carried out in experimental conditions, and the micro-needle experiment was carried out from the basic experiment to obtain the experimental conditions. Experimental results show that as the voltage and current increase, the surface roughness improved and the gloss is improved. So, the best result for this experiment was obtained in condition 6, which improved micro-needle.