• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.38 no.5 s.118
• /
• pp.47-53
• /
• 2006

To meet the ever increasing quality demand of coated papers and duplex boards, the local gloss variation and print unevenness must be avoid. To do this, surface roughening phenomenon which affects local gloss and print unevenness was investigated. In this study, the effect of roughness and densification of sheet obtained at various calendering conditions on surface roughening was examined. To evaluate the calendering effect properly we introduced a new value of roughening index by moisture for evaluation of surface roughening. Caliper and roughness of sheet decreased with increasing of calendering temperature and pressure, and the remarkable reduction of those properties occurred at the temperature around Tg. Roughening index increased when the amount of water increased and calendaring temperature and pressure increased. And as the sheet became denser by calendering, the roughening index increased to some extent. But roughening index by moisture is the lowest for sheet precalendered at higher temperature condition. When the surface of calendered sheet is rougher, there is more roughening of surface. The severe condition of calendering made the roughening index by moisture small.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2006.06b
• /
• pp.485-488
• /
• 2006

Surface roughening which is occurred by interaction between base paper and water in coating color deteriorates surface properties of coated paper. In this study, the effect of calendering variables on surface roughening and the relationship between hot calendering and water penetration depth were investigated. BCTMP handsheets were calendered at the various conditions of temperature and linear load, and its PPS roughness was measured before and after moistening to evaluate surface roughening. To determine water penetration depth, thickness was measured from the cross sectional images of sheet which were obtained using CLSM technique. High pressure calendering was beneficial to reduce surface roughness before coating but its smoothening effect was mostly lost by contact with water. On the contrary, sheet calendered at the highest temperature showed the lowest roughening. High temperature calendering allowed the smallest penetration of water into fiber network because of sufficient deformation and densification in top side of z-direction of sheet. Consequently, hot calendering could be the effective way to reduce surface roughening and unevenness of paper surface.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2011.05a
• /
• pp.130-130
• /
• 2011

vertical light-emitting diodes의 표면을 건식과 습식 두 가지 공정을 통해 식각하여 roughening을 주었고, 또한 이 고정으로 인해 표면이 전체적으로 거칠기를 가지므로써 외부 양자 효율의 증가를 기대하였다.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2022.11a
• /
• pp.89-90
• /
• 2022

Arc metal spraying is a widely used method for improving the performance of construction structures such as corrosion resistance and electromagnetic wave shielding. However, when arc metal spraying is applied to a concrete structure, adhesion performance may deteriorate. Therefore, the effect of each surface treatment method on the physical properties between the arc metal spray coating and concrete was reviewed by evaluating the deposition efficiency and adhesion performance according to the arc metal spray surface treatment method (surface reinforcing agent, roughening agent, and sealing agent). As a result, it is suggested as an optimal surface treatment condition to induce non-interface failure by using a roughening agent and to improve the properties of concrete and metal coatings by applying a surface reinforcing agent and sealing agent.

• Tribology and Lubricants
• /
• v.7 no.1
• /
• pp.16-27
• /
• 1991

The mechanism of failure of lubricated surfaces at high sliding speeds was investigated. Experiments were performed with the ball-on-flat and cylinder-on-flat geometries, using lubricants of four different chemical reactivities. Surface failure was found to not be predictable using the ratio, $\lambda$, of fluid film thickness to composite surface roughness except when chemically inert lubricants are used. Even then the influence of temperature rise on fluid film thickness does not adequately explain the low load carrying capacity of lubricants at high sliding speeds, which causes surface failure. The protective layers on sliding surfaces that form by chemical reaction with the lubricant were found to reduce the surface roughening and increase the load carrying capacity of surfaces to values of $\lambda$ as low as 0.03. Neither the surface roughening nor the formation of the protective layers have been incorporated into failure models for lubricated systems.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2012.11a
• /
• pp.171-171
• /
• 2012

In this study, we fabricated the high-brightness AlGaInP-based red light emitting diodes (LED)s using by direct printing technique and inductive coupled plasma (ICP) reactive ion etching (RIE). In general, surface roughening was fabricated by wet etching process to improve the light extraction efficiency of AlGaInP-based red LED. However, a structure of the surface roughening, which was fabricated by wet etching, was tiled cone-shape after wet etching process due to crystal structure of AlGaInP materials, which was used as top-layer of red LED. This tilted cone-shape of surface roughening can improve the light extraction of LED, but it caused a loss of the light extraction efficiency of LED. So, in this study, we fabricated perfectly cone shaped pattern using direct printing and dry etching process to maximize the light extraction efficiency of LED. Both submicron pattern and micron pattern was formed on the surface of red LED to compare the enhancement effect of light extraction efficiency of LEDs according to the diameter of sapphire patterns.After patterning process using direct printing and ICP-RIE proceeded on the red LED, light output was enhanced up to 10 % than that of red LED with wet etched structure. This enhancement of light extraction of red LED was maintained after packaging process. And as a result of analyze of current-voltage characteristic, there is no electrical degradation of LED.

• Journal of the Korean institute of surface engineering
• /
• v.5 no.1
• /
• pp.1-7
• /
• 1972

Copper -clad laminate(CCL) was fabricated and evaluated by bonding 35${\pm}$5${\mu}$ thick electroplated copper foils with a suitable adhesive to an insulating base such as phenolic resin laminate. In this study, electroplating methods and conditions were studied to produced good quality copper foils for printed circuit board applications. The electroplating bath solutions used were a copper-sulfate solution and a concentrated copper fluoborate solution. A surface roughening treatment that improved the adhesive strength of copper foils with an insulating laminate was also developed . A conventional copper sulfate solution containing sulfuric acid was used for the roughening treatment.

• The Journal of Korean Academy of Prosthodontics
• /
• v.18 no.1
• /
• pp.49-57
• /
• 1980

The adhesive mechanisms on the metal-ceramic restorations have been reported to be mechanical interlocking, chemical bonding, compressive force, and Van der Waal's force, etc. Of these, the mechanical interlocking and chemical bonding forces are thought to affect the adhesive force between Ni-Cr alloy and porcelain. This study investigates the adhesion of Ni-Cr alloy to porcelain according to surface treatment. For this purpose, the following experiments were made; The compositions of Ni-Cr alloy as cast by emission spectrograph, and the oxides produced on Ni-Cr alloy during degassing at $1850^{\circ}F$ for 30 minutes in air and in vacuum were analyzed by X-ray diffractograph. The metal phases of Ni-Cr alloy were observed according to porcelain-baking cyclic heat treatment by photo microscope and the distribution and the shift of elements of Ni-Cr alloy and porcelain and the failure phases between Ni-Cr alloy and porcelain by scanning electron microscope. The adhesive force between Ni-Cr alloy and porcelain was measured according to surface treatment with oxidization and roughening by Instron Universal Testing Machine. Results were as follows; 1. The metal phases of Ni-Cr alloy as cast and degassing state showed the enlarged and fused core, but when subjected to porcelain-baking cyclic heat treatment, showed a dendrite growing. 2. The kinds of metal oxides produced on Ni-Cr alloy during degassing were found to be NiO and $Cr_2O_3$. 3. The distribution of elements at the interface of Ni-Cr alloy and porcelain in degassing state showed demarcation line, but in roughening state, showed mechanical interlocking phase. 4. The shift of elements at the interface occurred in both states, but the shift amount was found to be larger in roughening than in degassing. 5. The adhesive force between Ni-Cr alloy and porcelain was found to be $3.45{\pm}0.93kg/mm^2$, in degassing and $3.82{\pm}0.99kg/mm^2$, in roughening. 6. The failure phase between Ni-Cr alloy and porcelain showed the mixed type failure.

• Journal of the Korean institute of surface engineering
• /
• v.31 no.6
• /
• pp.345-358
• /
• 1998

The evolution of surface roughness and morphology in epitaxial Si and $Si_{0.7}Ge{0.3}$ alloys grown by UHV opm-beam sputter deposition onto nominally-singular, [100]-, and [110]-mi-scut Si(001) was investigated by stomic force microscopy and trasmission electron microscopy. The evolution of surface roughness of epitaxial Si films grown at $300^{\circ}C$ is inconsistent with conventional scaling and hyperscaling laws for kineti roughening. Unstable growth leading to the formation of mounds separated by a well-defined length scale is observed on all substrates. Contraty to previous high-temperature growth results, the presence of steps during deposition at $300^{\circ}C$ increases the tendency toward unstable growth resulting in a much earlier development of mound structures and larger surface roughnesses on vicival substrates. Strain-induced surface roughening was found to dominate in $Si_{0.7}Ge{0.3}$ alloys grown on singular Si(001) substrates at $T_S\ge450^{\circ}C$ where the coherent islands are prererentially bounded along <100> directions and eshibt {105} facetting. Increasing the film thickness above critical values for strain relaxation leads to island coalescence and surface smoothening. At very low growth temperatures ($T_s\le 250^{\circ}C$), film surfaces roughen kinetically, due to limited adatom diffusiviry, but at far lower rates than in the higher-temperature strain-induced regime. There is an intermediate growth temperature range, however, over which alloy film surfaces remain extremely smooth even at thicknesses near critical values for strain relaxation.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2006.04a
• /
• pp.102-102
• /
• 2006