• Environmental Engineering Research
• /
• v.22 no.1
• /
• pp.19-30
• /
• 2017

Direct catalysis of vapors from vacuum pyrolysis of biomass was performed on MCM-41 to investigate the effects of operating parameters including catalyzing temperature, catalyzing bed height and system pressure on the organic yields. Optimization of organic phase yield was further conducted by employing response surface methodology. The statistical analysis showed that operating parameters have significant effects on the organic phase yield. The organic phase yield first increases and then decreases as catalyzing temperature and catalyzing bed height increase, and decreases as system pressure increases. The optimal conditions for the maximum organic phase yield were obtained at catalyzing temperature of $502.7^{\circ}C$, catalyzing bed height of 2.74 cm and system pressure of 6.83 kPa, the organic phase yield amounts to 15.84% which is quite close to the predicted value 16.19%. The H/C, O/C molar ratios (dry basis), density, pH value, kinematic viscosity and high heat value of the organic phase obtained at optimal conditions were 1.287, 0.174, $0.98g/cm^3$, 5.12, $5.87mm^2/s$ and 33.08 MJ/kg, respectively. Organic product compositions were examined using gas chromatography/mass spectrometry and the analysis showed that the content of oxygenated aromatics in organic phase had decreased and hydrocarbons had increased, and the hydrocarbons in organic phase were mainly aliphatic hydrocarbons. Besides, thermo-gravimetric analysis of the MCM-41 zeolite was conducted within air atmosphere and the results showed that when the catalyst continuously works over 100 min, the index of physicochemical properties of bio-oil decreases gradually from 1.15 to 0.45, suggesting that the refined bio-oil significantly deteriorates. Meanwhile, the coke deposition of catalyst increases from 4.97% to 14.81%, which suggests that the catalytic activity significantly decreases till the catalyst completely looses its activity.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.20 no.6
• /
• pp.29-37
• /
• 2016

This paper proposes a shape optimization of the metal boss for a composite motor case using finite element analysis. For the structural safety and the weight reduction of the composite motor case, under the internal pressure, the fiber stress in the dome area and the tightening bolt stress are constrained and the boss weight is set to objective function, respectively. The response surface models are constructed for the performance characteristics by using response surface method. The significance of the design variables about the performance characteristics is evaluated through the ANOVA(analysis of variance) and the goodness of fit test for the constructed model is performed through the regression analysis. The SQP(sequential quadratic programming) algorithm is used for the optimization and the proposed method is verified by performing structural analysis for the optimum shape.

• Journal of the Korean GEO-environmental Society
• /
• v.12 no.10
• /
• pp.57-62
• /
• 2011

This study investigated the effects of various inorganic anions($Cl^-$, $NO_3{^-}$, $HCO_3{^-}$) on the Methyl tert Butyl Ether(MTBE) degradation by photocatalysis using statistical method. Generally, this process in general demands the generation of hydroxyl radicals(OH radical) in solution in the presence of UV light. The generation of radicals were affected by inorganic anions in solution that inhibited the photodegradation by their trapping hydroxyl radicals. The effects of inorganic anions were mathematically described as the independent variables such as $Cl^-$, $NO_3{^-}$, and $HCO_3{^-}$, and these were designed by mixture analysis that was one of the response surface methodology(RSM). Regression analysis on ANOVA showed significant p-value(p<0.0001) and high coefficients for determination value($R^2$=99.28%, ${R^2}_{adj}$=98.91%). Contour and response surface plots showed that the effects of inorganic anions for MTBE photodegradation based on $UV/H_2O_2$ process. In the result, $Cl^-$ and $HCO_3{^-}$ inhibited the photodegradation of the MTBE by their trapping hydroxyl radicals, and the interaction by these two factors was observed.

• Geomechanics and Engineering
• /
• v.7 no.2
• /
• pp.149-164
• /
• 2014

One of the most advanced classes of techniques for ground response analysis is based on the use of Transfer Functions. They represent the ratio of Fourier spectrum of amplitude motion at the free surface to the corresponding spectrum of the bedrock motion and they are applied in frequency domain usually by FFT method. However, Fourier spectrum only shows the dominant frequency in each time step and is unable to represent all frequency contents in every time step and this drawback leads to inaccurate results. In this research, this process is optimized by decomposing the input motion into different frequency sub-bands using Wavelet Multi-level Decomposition. Each component is then processed with transfer Function relating to the corresponding component frequency. Taking inverse FFT from all components, the ground motion can be recovered by summing up the results. The nonlinear behavior is approximated using an iterative procedure with nonlinear soil properties. The results of this procedure show better accuracy with respect to field observations than does the Conventional method. The proposed method can also be applied to other engineering disciplines with similar procedure.

• Journal of Ocean Engineering and Technology
• /
• v.30 no.4
• /
• pp.260-267
• /
• 2016

Considering the effect of dynamic response amplification, a reliability analysis of an offshore wind turbine support structure under an earthquake is presented. A reliability analysis based on the dynamic response requires a large amount of time when using not only a level 3 approach but also level 2 such as a first order reliability method (FORM). Moreover, if a limit state is defined by using the maximum stress at a structural joint where stress concentration occurs, a three-dimensional element should be used in the finite element analysis. This makes the computational load much heavier. To deal with this kind of problem, two techniques are suggested in this paper. One is the application of a quasi-static structural analysis that takes the dynamic amplification effect into account. The other is the use of a stress concentration factor to estimate the maximum local stress. The proposed reliability analysis is performed using a level 2 FORM and verified using a level 3 simulation approach.

• Food Science and Preservation
• /
• v.10 no.3
• /
• pp.314-319
• /
• 2003

This study was conducted to the optimize salting process of eggplant for development new product and enhancement quality for export. Three variables by five level central composite design and response surface methodology were used to determine optimum conditions for salting time, temperature and salt concentration. Optimization of the process was conducted using the combination of the moisture content, salinity and color of surface and inside of salted eggplant. The regression polynomial model was suitable (P>0.05) by Lack-of-Fit analysis with highly significant. To optimize the process, based on surface response and contour plots, the individual contour plots of the response variables were superimposed. The optimum conditions for this process were 6 days and 15$^{\circ}C$ at 30％ concentration under the optimum of restricted variables as moisture content was below 84％, salinity was below 14％, L and b value of surface were 10 to 20 and below 0, L value and b value of inside were 70 to 75 and 16 to 18.

• Wind and Structures
• /
• v.29 no.4
• /
• pp.235-246
• /
• 2019

Wind loading is one of important loadings that should be considered in the design of large hyperbolic natural-draught cooling towers. Both external and internal surfaces of cooling tower are under the action of wind loading for cooling circulating water. In the previous studies, the wind loads on the external surface attracted concernedly attention, while the study on the internal surface was relatively ware. In the present study, the wind pressure on the internal surface of a 220 m high cooling tower is measured through wind tunnel testing, and the effect of ventilation rate of the packing layer on internal pressure is a major concern. The characteristics of internal wind pressure distribution and its effect on wind-induced responses calculated by finite element method are investigated. The results indicate that the wind loading on internal surface of the cooling tower behaves remarkable three-dimensional effect, and the pressure coefficient varies along both of height and circumferential directions. The non-uniformity is particularly strong during the construction stage. Analysis results of the effect of internal pressure on wind-induced responses show that the size and distribution characteristics of internal pressure will have some influence on wind-induced response, however, the outer pressure plays a dominant role in the wind-induced response of cooling tower, and the contribution of internal pressure to the response is small.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.224-225
• /
• 2009

Aluminium nitride thin film was deposited on Au electrode and Si substrate by radio frequency sputtering system. X-ray diffraction (XRD) was utilized to identify the AlN phase, and Atomic Force Microscope (AFM) was used to obtain the images of surface morphology and roughness value of AlN thin film. The result of XRD and AFM measurement showed that the AlN thin film has strong c-axs orientation and smooth surface. In order to investigate piezoelectric response and polarization properties along to the direction of electric field, PFM (Piezoresponse Force Microscope) system was used, and the images of piezoelectric response due to switching of polarization was observed by PFM.

• Geotechnical Engineering
• /
• v.1 no.1
• /
• pp.13-20
• /
• 1985

In this paper, earthquake response of the Bangkok area in Thailand was analyzed in terms of the acceleration response spectrum and maximum acceleration of the computed surface motions. The program SHAKE was employed to analyse the ground motion. With increasing the maximum acceleration and predominant period of given base rock motion, the computed maximum ground surface acceleration increases. but converges on a maximum value of about 0.39. The characteristics of earthquake response spectrum in the Bangkok area are also discussed and illustrated.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.48 no.6
• /
• pp.442-450
• /
• 1999

In this paper, we have fabricated Langmuir-Blodgett(LB) films by LB technique and evaluated the deposited status of LB films by UV-vis absorbance. It was found thatthe thickness of LB films per a layer are $27~30[{\AA}]$ by ellipsometry. The responeses between LB films and organic gases were investigated using by I-V characteristics of LB films and F-R diagram of quartz crystal. The response orders between LB films and organic gases observed by I-V characteristics were as following ; chloroform, methanol, acetone and ethanol in the order of their short chain length. The response mechanism between LB films and organic gases observed by F-R diagram of quartz crystal could be modeled on adsorption at surface, penetration, desorption at surface and inside.