• International Journal of Automotive Technology
• /
• 제8권3호
• /
• pp.343-349
• /
• 2007

One of the useful technologies for light-weightening of components required in the automobile and machine industry is to use high strength materials. To improve material properties, the carbonizing treatment, nitrifying treatment, and shot-peening method are representatively applied. However, the shot-peening method is generally used to remove surface defect on steel and to improve the fatigue strength of the surface. Benefits of shot-peening are increasing resistance against fatigue, stress corrosion cracking, fretting, galling, erosion and closing of pores. In this paper, the effect of shot-peening on the corrosion of SUP-9 steel immersed in a 3.5% NaCl solution and corrosion characteristics from heat treatment during the shot peening process has been investigated. The immersion test was performed on four kinds of specimens. Corrosion potential, the polarization curve, residual stress etc. Were analyzed from the experimental results.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2006년도 정기 학술대회 논문집
• /
• pp.836-840
• /
• 2006

Design optimization of layered plates bonding process is conducted to achieve high product quality by considering uncertainties in a manufacturing process. During the cooling process of the sequential sub-processes, different thermal expansion coefficients lead to residual stress and displacement. thus resulting in defects on the surface of the adherent. So robust process optimization is performed to minimize the residual stress mean and variation of the assembly while constraining the distortion as well as the instantaneous maximum stress to the allowable limits. In robust process optimization, the dimension reduction (DR) method is employed to quantify both reliability and quality of the layered plate bonding. Using this method. the average and standard deviation is estimated. Response surface is constructed using the statistical data obtained by the DRM for robust objectives and constraints. from which the optimum solution is obtained.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2000년도 제31회 춘계학술대회
• /
• pp.159-165
• /
• 2000

In this paper the residual stresses on lubricated sliding surfaces were measured during break-in procedure and up to scuffing by the X-ray diffraction method. The cylinder-on-disk type tribometer was used with the line-contact geometry. Scuffing tests were done using a constant load. In the break-in procedure the loads were increased from very low values in several steps. It was found that the sliding surfaces with break-in represented relatively higher values of residual compressive stresses than those without break-in. The residual stresses below the surfaces showed the small amount of stress increases. The results of scuffing tests with and without break-in showed the same trends as break-in tests did. However, in case of tests with break-in procedure the stresses below the surfaces showed very large increases in the residual compressive stresses. From the tests of break-in and scuffing, it was found that the increases in scuffing lives were related with the increases of residual stresses on the lubricated sliding surfaces with break-in.

• 한국압력기기공학회 논문집
• /
• 제6권2호
• /
• pp.34-41
• /
• 2010

This work is concerned with the analysis of stress corrosion cracking(SCC) behavior of Alloy 600 nozzle penetration mock-up according to a residual stress induced by a dissimilar metal welding(DMW) in a nuclear reactor pressure vessel. The effects of the dimension and materials of the nozzle penetration on the deformation and the residual stress induced by DMW were investigated using a finite element analysis(FEA). The inner diameter(ID) change of the nozzle by DMW and its dependance on the design variables, calculated by FEA, were well consistent with those measured from the mock-up. Accelerated SCC tests were performed for three mock-ups with different wall thicknesses in a highly acidic solution to investigate mainly the effect of the residual stress on the SCC behavior of Alloy 600 nozzle. From a destructive examination of the mock-up after the tests, the SCC behavior of the nozzle was fairly related with the residual stress induced by DMW : axial cracks were found in the ID surface of the nozzle within the J-weld region where the highest tensile hoop stress was predicted by FEA, while circumferential cracks were observed beyond both J-weld root and toe where the highest tensile axial stress was expected.

• 한국정밀공학회지
• /
• 제34권2호
• /
• pp.151-156
• /
• 2017

Shot peening is widely used to improve the fatigue life and strength of various mechanical parts and an accurate method is important for the prediction of the compressive residual stress caused by this process. A finite element (FE) model with an elliptical multi-shot is suggested for random-angled impacts. Solutions for compressive residual stress using this model and a normal random vertical-impact one with a spherical multi-shot are obtained and compared. The elliptical multi-shot experimental solution is closer to an X-ray diffraction (XRD) than the spherical one. The FE model's peening coverage also almost reaches the experimental one. The effectiveness of the model based on an elliptical shot ball is confirmed by these results and it can be used instead of previous FE models to evaluate the compressive residual stress produced on the surface of metal by shot peening in various industries.

• 대한기계학회논문집
• /
• 제16권9호
• /
• pp.1632-1642
• /
• 1992

본 연구에서는 방전가공(electric disharge machining, EDM) 또는 공기연마 분사기(air-abrasive jet machine, AJM) 가공에 의하여 인장 시험편 또는 외팔보 시험 편에 구멍깊이를 증가시켜 가면서 구멍을 뚫었다. 여기에서 방저가공(EDM)을 채택한 것은 구멍깊이를 직접 계측하는 것이 가능하여 구멍깊이 측정 오차에 기인하는 잔류응 력 측정오차를 최소화 할 수 있기 때문이며, 공기연마 분사기를 채택한 것은 구멍을 뚫는 동안 가공응력을 유발시키지 않기 때문이었다. 위 인장 시험편 또는 외팔보 시 험편을 이용하여 균일한 응력장과 두께 방향으로 변하는 선형적 구배응력장을 구현하 고, 이 때 각각 구멍깊이가 다른 원통형 막힘 구멍으로 부터 이완되는 스트레인을 계 측하였다. Schajer가 제안한 멱급수법과 최소장승법을 적용하여 균일응력장 또는 구 배 응력장에서 측정되는 스트레인을 잔류응력으로 환산하였으며, 환산된 잔류응력과 실제로 작용하는 응력을 비교하므로서 이론적으로 제시된 멱급수법과 최소자승법의 타 당성을 실험적으로 검토하는데 본 연구의 목적이 있다. 이 때 얕은 구멍깊이 (0.3∼ 1.2mm)에서 측정되는 스트레인을 이용하여 Schajer의 제안에 따라 잔류응력을 산정하 므로서, 잔류응력 계측 대상 구조물을 가급적 덜파괴시키며 잔류응력을 측정할 수 있 는지 여부를 실험적으로 검토하였다.

• 소성∙가공
• /
• 제14권8호통권80호
• /
• pp.704-711
• /
• 2005

The influence of process parameters in drawn wire on residual stresses was investigated. Based on a FE-simulation of the wire drawing process, the effects of process parameters such as semi-die angle, reduction, friction coefficient and bearing length on the residual stresses were investigated. The validity of the FE-simulation results was verified by the comparison of the previous simulated results with experimental data. In this study, semi-die angle and die reduction have significant effect on the residual stresses at the surface of drawn wire. Several methods such as, addition of axial tension, application of skin pass, straightening in multi-roll straightener etc, were suggested in the previous studies to reduce the residual stresses. In this study, the results show that the concurrent application of skin pass with low die reduction and low semi-die angle at the final stage of drawing operation reduces dramatically the both axial and hoop residual stresses after drawing

• 한국해양공학회지
• /
• 제18권6호
• /
• pp.91-95
• /
• 2004

In this study, to investigate the effects of shot peening on crack growth behavior, crack growth tests are conducted on spring steels and shot peened cracks. The probabilistic crack growth equation, which can represemt the sigmoidal crack growth behavior as recently reported by Kim and Shim, is used to evaluate the experimental results. The results show that fatigue cracks grows slower in the shot peened specimen than in the unpeened and, due to the compressive residual stress occurring on the specimen surface. In the case of the shot peened specimen, the initial stress intensity factor range and the fracture toughness is higher than the non-peened specimen because the compressive residual stress affects crack growth and fracture of the specimen.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 춘계학술대회 논문집
• /
• pp.697-703
• /
• 1996

Fatigue strength of high strengthsteels are variable with many different surface treatment. It is well known that residual compressive stress retard fatigue crack growth rate(or arrest crack). High strngth steels are manufactured by following process. Heat treatment, shot peening and chromium plating process. High strength steel(HRC40 or above) which are subjected to fatigue load and dynamic load, chromium plated parts shall be peened in accordance with requirements and baked after plating. The purpose of this paper is to compare and discuss the influence of surface treatment and hydrogen embrittlement on fatigue strength of high strength steel. Therefore, fatigue test was performed to investigate influence of surface treatment. The results shows that shot peening is very effect method in creasing fatigue life and after plating, baking process is essential to prevent hydogen failure. In this paper, the experimental investigation is made to clarify the influence of shot peening conditions and baking process on fatigue strength of high strength steel.

• 한국정밀공학회지
• /
• 제18권3호
• /
• pp.35-39
• /
• 2001

The precision grinding process is carried out with fine-cutting operation after coarse-cutting operation. So, the laminated grinding wheel has been developed to reduce the ineffectiveness induced by changing the operations. In this study, to investigate the possibility of the practical use of the laminated grinding wheel, the surface residual stress of the workpiece ground by the laminated grinding wheels was compared with that ground by the general grinding wheel, and the influence of the difference in grain sizes, between the coarse grit and fine grit of the laminated grinding wheel, on the surface roughness of the workpiece was investigated.