• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.7
• /
• pp.116-123
• /
• 2008

In the fossil power plant, the reliability of the components which consist of the many welded parts depends on the quality of welding. The residual stress is occurred by the heat flux of high temperature during weld process. This decreases the mechanical properties as the strength of fatigue and fracture or causes the stress corrosion cracking and fatigue fracture. Especially, the accidents due to the residual stress occurred at the weld parts of high-temperature and high-pressure pipes and steam headers. Also, the residual stress of the welded part in the recently constructed power plants has been brought into relief as the cause of various accidents. The aim of this study is the measurement of the residual stress using the x-ray diffraction method. The merits of this are more accurate and applicable than other methods. The materials used for the study is P92 steel for the use of high temperature pipe on super critical condition. The variables of tests are the post-weld heat treatment, the surface roughness and the depth from the original surface. The test results were analyzed by the distributed characteristics of the full width at half maximum intensity (FWHM) in x-ray diffraction intensity curve and by the relation of hardness with FWHM.

• Journal of Welding and Joining
• /
• v.2 no.2
• /
• pp.54-61
• /
• 1984

Construction of welding structure is greatly dependent upon welding heat cycle. Fracture toughness is decreased remarkablely due to coarse grained HAZ and inequal residual stress of three dimensions to originate in welding. Post weld heat treatment(PWHT) is carried out to increase the fracture toughness of HAZ and to remove the residual stress. There occur some problem such as toughness decrement and stress relief cracking(SRC) in the coarse grained HAZ subject to the effect of tempering treatment. Therefore, in this paper, the effect of heat inputs affecting cooling rate and PWHT under the no stress on fracture toughness were evaluated by crack opening displacement (COD), SEM and micro-hardness test. Experimental results are as follows; 1. Fracture toughness of weld HAZ is dependent upon weld heat cycle and it is decreased with increment of heat input, but the degree of improvement of fracture toughness after PWHT was linearly increased with heat input. 2. Hardness of the parent metal is not changed, but the softening of coarse grained HAZ is remarkable due to PWHT. 3. Fracture surface of as-weld show the perfect brittle fracture with the cleavage fracture, but after PWHT they appear the ductile fracture surface with dimple.

• Journal of The Geomorphological Association of Korea
• /
• v.25 no.4
• /
• pp.103-116
• /
• 2018

The purposes of this research are as follows: First, to reconstruct the optimal locational environment of the Bronze Age settlement in Cheonan Baekseok-dong (hereinafter referred to as the study settlement). Second, to identify the priority ranking of the topographical factors that influenced the Bronze Age people when selecting their the settlement location. For these reasons, the topographical factors of the 200 Bronze Age dwellings (hereinafter referred to as dwellings) confirmed in the survey area were analyzed through the ridge's environmental perspective. The results are asfollows: First, the optimal ridge environment of the Bronze Age settlement is largely a sub-ridge in N-S direction (for example, NNW-SSE, N-S, NNESSW), especially at the top (Crest slope, Crest flat) of the south-facing aspect of the ridge. Second, when the Bronze Age dwellers selected a residential location, they carefully considered topographical factors in the following order: (1) the slope direction of the ridge surface, (2) the micro-landform of the ridge, (3) the ridge scale, (4) the ridge direction, and (5) the surface relief. The results of this study could be used as basic data in related fields such as archaeology, quaternary research, and traditional architecture and so on.

• The Journal of Korea Robotics Society
• /
• v.17 no.1
• /
• pp.48-57
• /
• 2022

In this paper, we propose a legged landing platform for the quadcopter taking off and landing in the ship environment. In the ship environment with waves and winds, the aircraft has risks being overturned by contact impact and excessive inclination during landing on the ship. This landing platform has four landing legs under the quadcopter for balancing and shock relief. In order to make the quadcopter balanced on ships, the position of each end effector was controlled by PID control. And shocks have mainly happened when quadcopter contacts the ship's surface as well as legs move fast. Hence, impedance control was used to cope with the shocks. The performance of the landing platform was demonstrated by a simulation and a prototype in three sea states based on a specific size of a ship. During landing and tracking the slope of the ship's surface, oscillations of rotation and translation from the shock were mitigated by the controller. As a result, it was verified that transient response and stability got better by adding impedance control in simulation models and prototype experiments.

• Journal of Welding and Joining
• /
• v.5 no.2
• /
• pp.9-16
• /
• 1987

Post weld heat treatment (PWHT) is carried out to increase the fracture toughness in heat affected zone(HAZ) and remove the residual stress. There occur some problems such as toughness decreement and stress relief cracking(SRC) in the coarse grained HAZ subjected to the effect of tempering treatment. Especially, embitterment of structure directly relates to the mode of fracture and is appeared as the difference of fracture surface, that is, grain boundary failure. Therefore, in this paper, PWHT was carried out under the stress of 0, 10, 20 and $30kg/cm^2$ to simulate residual stress in HAZ welded by heat input of 10, 30 and 40KJ/cm. Applied stress in weld HAZ during PWHT assisted precipitin of over saturated alloying element in the structure, and grain boundary failure according to welding heat input didn't almost appear at the heat input of 10 KJ/cm, but it appeared from being the applied stress of $30kg/cm^2$ at $30KJ/cm and 20kg/mm^2$ at 40KJ/cm.

• Proceedings of the KSRS Conference
• /
• 2002.10a
• /
• pp.308-311
• /
• 2002

Radar interferometric phase is sensitive to both ground topography and coherent surface displacement. The basic tactics of differential interferometric synthetic aperture radar (DInSAR) technique are to separate the two effects. Applications of DInSAR to Duk-Po area in Busan were studied. In the study area, an abrupt subsidence, possibly caused by sub-way construction, was observed by JERS-1 SAR interferometry. Differential interferograms were generated using twenty-three JERS-1 SAR data acquired between April 24, 1992, and August 7, 1998. Because the area is relatively flat with little topographic relief the topographic effects were not removed. A phase filtering and interferogram techniques were applied to increase fringe clarity as well as to decrease decorrelation error. The stacking improves the quality of interferograms especially when the displacement is discontinuous. The interferograms clearly show the evidence of subsidence along Duk-Po subway railroad. These results demonstrate that the interferogram stacking technique can improve the detectability of radar interferometry to an abrupt displacement and DInSAR is useful to geological engineering applications.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.648-651
• /
• 2009

탄소섬유강화플라스틱(CFRP:Carbon Fiber Reinforced Plastic)용기의 외부에 화재가 발생할 경우 함침된 수지(Resin)가 탄화되면서 자체 강도가 약화되고 충전된 가스가 외부 온도 상승에 따라 압력 상승이 발생하여 용기의 폭발로 이어지는 사고가 발생할 개연성이 높다. 화염 노출조건에서 복합재료 용기의 폭발을 방지하기 위하여 용기용 밸브에 내장된 온도감응식 압력안전장치(TPRD:Thermally activated Pressure Relief Device) 작동 성능을 검증하기 위한 방법으로 화염실험(Bonfire test)를 실시하고 있으나, 개방 공간에서 실시되는 이 실험은 표면 온도 변화가 매우 크게 발생하여 실험에 대한 재현성(Reproducibility)에 의문이 제기되고 있다. 따라서, 표면 온도를 일정하게 유지하기 위한 실험 방법의 개선이 필요하다. 본 연구에서는 경유+heptane을 이용한 전체 화염에 노출되는 경우와, 천연가스를 이용한 단일화염에 노출되는 경우의 실험 결과 비교를 통하여 화염 노출 표면 온도를 일정하게 유지하기 위한 가열 방법의 타당성을 검토하였다. 또한, 복합재료 라이너(Liner)의 온도 변화 비교를 통하여 집중화염 노출 조건에서 열전달 특성을 알아보았다.

• Journal of the Speleological Society of Korea
• /
• no.80
• /
• pp.5-9
• /
• 2007

Ulleungdo and Dokdo is special island to all Korean people, The purpose of this study is to collect, sorting, analysis and rearrangement the photo data. The data collected from the published books and new photos. The quantity of data is so big, that it is necessary to divide the volume to publishing the books. For example, aerial photos(including marine topography), the relief of surface, culture and history, urban and settlement, sightseeing and economy, maps and figure and etc. The effect of the study is clear to the civics and students about patriotic sentiment etc.

• Journal of the Optical Society of Korea
• /
• v.18 no.6
• /
• pp.762-765
• /
• 2014

We fabricated a periodically poled lithium niobate (PPLN) by direct laser-writing of a quasi-phase-matching (QPM) structure in photolithographic process. Because we do not need to prepare a photomask by electron-beam writing, the "maskless" process shortens the fabrication time and significantly reduces the cost. We evaluated the poling quality of the direct laser-written PPLN by measuring the diffraction noise from the surface relief pattern of the fabricated QPM grating and comparing the results to those from a conventional PPLN made with a photomask. The quality of the PPLN fabricated by direct laser-writing was shown to be equivalent to that fabricated by the conventional method.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.7-10
• /
• 2001

We have developed a prototype dedicated CAM system for machining a human bust that is not a relief. The input is STL file format, and the output is NC-codes for machining on a 3-axis general purpose CNC milling machine with an index table attached. Main modules are STL import, STL transformation, modeling jig/fixture, master model generation, and calculation of machining area. System architecture is proposed and main modules are briefly described. We adopted the angle between tool-axis and the surface normal vector to calculate machining area, and tested at several degrees.