• 한국정밀공학회지
• /
• 제16권3호통권96호
• /
• pp.208-214
• /
• 1999

The purpose of this paper is to develop a profile modification technique of spur gears and its computer program for the prevention of gear tooth overlap. In the gear system, tooth overlap produces an impact at the initial contact of some tooth pairs. In this analysis, contact surface was assumed to be unbonded and frictionless under small deformation and stain. The problem is formulated by a variational statement with inequality constraint. Tooth load sharing is obtained by the application of contact theory, and overlap is known by the analysis of deformation. After carrying out the profile modification of gear tooth, we verified the reasonable results.

• 한국지반공학회논문집
• /
• 제15권3호
• /
• pp.131-149
• /
• 1999

여러 연구들을 통하여 표면 거칠음 정도가 접촉면 전단력에 매우 중요함이 밝혀졌으며, 따라서 그 역할을 충분히 이해하기 위해서는 표면 거칠음 정도가 정확히 정량화 되어야 한다. 이 연구에서는 표면 형상을 정량화하기 위하여 일반적으로 사용되는 표면 거칠기 매개변수와 측정방법에 대하여 여러 참고문헌들을 검토하였다. 이것을 바탕으로 Normalized Roughness Parameter, $R_n$ (Uesugi and Kishida, 1986), Profile Roughness Parameter, $R_L$, 그리고 Surface Roughness Parameter, $R_n$(Dove and Frost, 1996)가 적합한 표면 거칠기 매개변수로 선택되었으며, 디지털 이미지 분석 시스템을 이용한 Optical Profile Microscopy(OPM) 방법을 표면 거칠음 측정방법으로 선택하였다 이 실험장비를 이용하여 일반적으로 사용되는 지오멤브레인의 표면과 표면 패턴을 대표하는, 표면이 매끄러운 것과 3가지 종류의 돌기형 HDPE 지오멤브레인을 사용하여, 전단 시험에 사용되지 않았던 지오멤브레인과 전단시험후의 지오멤브레인에 대한 표면 거칠음 정도의 정량화 작업을 수행하였다. 그 결과, $R_L과\; R_S$값은 이 연구에 사용된 지오멤브레인의 거칠음 정도를 충분한 측정범위로 표현할 수 있는 매개변수로 밝혀졌으나, $R_n$값은 충분히 표면 거칠음 정도의 차이를 표현하기에는 부족하게 매우 좁은 변화 범위를 나타내었다. 이 연구는 접촉면에서 표면 거칠음 정도가 접촉면 전단력에 미치는 영향을 조사하고자 우선적으로 표면 거칠음 정도의 정량화 작업을 연구한 것이다.

• 대한기계학회논문집B
• /
• 제26권8호
• /
• pp.1077-1087
• /
• 2002

The heat (mass) transfer characteristics on the blade surface of a high-turning first-stage turbine rotor for power generation has been investigated by employing the naphthalene sublimation technique. A four-axis profile measurement system is developed successfully for the measurements of local sublimation depth on the curved surface In the leading edge region, there is a good agreement between the present heat (mass) transfer data and the previous result on a turbine blade with a moderate turning angle, but some discrepancies are found in the mid-chord heat (mass) transfer between the two results. The local heat (mass) transfer on the present suction surface is greatly enhanced due to an earlier boundary transition, compared with that on a turbine blade with a moderate turning angle, meanwhile there is only a slight change in the pressure-side heat (mass) transfer between the two different turbine rotors. In general, the heat (mass) transfer augmentation by the endwall vortices is found much higher on the suction surface than on the pressure surface.

• 비파괴검사학회지
• /
• 제30권6호
• /
• pp.569-577
• /
• 2010

Nonplanar surface geometries of components are frequently encountered in real ultrasonic inspection situations. Use of rigid array transducers can lead to beam defocusing and reduction of defect image quality due to the mismatch between the planar array and the changing surface. When a flexible array is used to fit the complex surface profile, the locations of array elements should be known to compute the delay time necessary for adaptive heam focusing. An alternative method is to employ the time reversal focusing technique that does not require a prior knowledge about the properties and structures of the specimen and the transducer. In this paper, a time reversal method is applied to simulate beam focusing of flexible arrays and imaging of point-like defects contained in specimens with nonplanar surface geometry. Quantitative comparisons are made for the performance of a number of array techniques in terms of the ability to focus and image three point-like reflectors positioned at regular intervals. The sinusoidal profile array studied here exhibits almost the same image quality as the flat, reference case.

• 한국정밀공학회지
• /
• 제27권12호
• /
• pp.22-27
• /
• 2010

The usage of ultra-precision machining is increasing by the manufacturing of precision optical elements such as camera lens, laser printer, CD player, DVD and microscope parts etc.. The WC alloy material is in wide use by mold core to improve the productivity and accuracy in manufacturing those precision parts. The WC alloy mould core can be machined effectively by the parallel grinding process which is an excellent technique for manufacturing of surface profile hard to machining materials such as the hardened metal alloy, Ceramics, Glass and so on. Magnetic assisted polishing as a final polishing process has also been utilized to obtain ultra-precision mirror surface with the elimination of traces presented on ground surface. It is able to deduce the optimal ultra-precision machining conditions of the WC alloy material from the experiment and analyses results.

• Tribology and Lubricants
• /
• 제31권5호
• /
• pp.205-212
• /
• 2015

In this research, effects of profile changes of stem section of the plunger on the lubrication characteristics of a fuel injection pump (FIP) were evaluated by hydrodynamic lubrication analysis. The clearance between plunger and barrel was divided into two regions, head and stem. The head was not involved in preventing a decrease of fuel oil pressure. So, research efforts were focused on both edges of the plunger’s stem. The two -dimensional Reynolds equation was used to evaluate lubrication characteristics with variations in viscosity, clearance and profile for a laminar, incompressible, unsteady-state flow. Moreover, the equilibrium equation of moment and forces in the vertical and horizontal directions were used to determine the motion of the plunger. The equations were discretized using the finite difference method. Lubrication characteristics of the FIP were investigated by comparing the dimensionless minimum film thickness, or film parameter, which is the ratio of minimum film thickness to surface roughness. Through numerical analyses, we showed that the profile of the lower edge of the stem had no effect on lubrication characteristics, but the profile of the upper edge had a significant influence on lubrication characteristics. In addition, changes in the profile were more effective in improving lubrication characteristics under low viscosity conditions.

• 한국군사과학기술학회지
• /
• 제20권2호
• /
• pp.231-237
• /
• 2017

The profile of unpaved road is an important issue in the reliability of endurance test. Efforts on measuring 2D road profile and analyzing the severity have been continued in the study of performing reliable endurance test evaluations through reflecting the results of such measurement and analysis. However, 2D road profile has limitation in measuring the profile in the road width direction because data is obtained along the trailer wheel track. Therefore, in order to measure 3-dimensional shape of road surface and construct severity DB of 3D road profile, Changwon Proving Ground(CPG) of Agency for Defense Development(ADD) developed 3D profilometer which is composed of laser scanner, IMU, GPS, encoder and so on. This paper focuses on the analysis of unpaved road severity using 3D road profile for army operation roads. This results will be used to manage test courses severity of CPG.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.2534-2539
• /
• 2007

Launch vehicles are exposed to aerodynamic heating conditions while flying at high Mach numbers in the atmosphere. In this study aerodynamic heating test for fairing nose-cone was done using ATSF(Aerodynamic Thermal Simulation Facility) and Engineering Model for fairing. ATSF is a facility that can simulate given temperature profile using about 4,000 halogen heaters on fairing model. Aerodynamic heating profile is got from result of thermal analysis using MINIVER, Thermal Desktop and SINDA/FLUINT. After aerodynamic heat test, it is found that initial temperature of fairing inner surface and thickness of BMS has important effects on temperature of fairing inner surface. Also it is confirmed that maximum temperature of fairing nose-cone inner surface during flight is lower than allowable temperature limit. Later, thermal correlation between thermal analysis and experimental results will be done using aerodynamic heating test result

• Korean Chemical Engineering Research
• /
• 제54권1호
• /
• pp.108-113
• /
• 2016

A miniaturized lab-scale Cu plating cell for the metallization of electronic devices was fabricated and its deposit uniformity and profile were investigated. The plating cell was composed of a polypropylene bath, an electrolyte ejection nozzle which is connected to a circulation pump. In deposit uniformity evaluation, thicker deposit was found on the bottom and sides of substrate, indicating the spatial variation of deposit thickness was governed by the tertiary current distribution which is related to $Cu^{2+}$ transport. The surface morphology of Cu deposit inside photo-resist pattern was controlled by organic additives in the electrolyte as it led to the flatter top surface compared to convex surface which was observed in the deposit grown without organic additives.

• 한국생산제조학회지
• /
• 제7권6호
• /
• pp.132-140
• /
• 1998

Recently, precision machining technology has been developed continuously in order to make high productivity and quality assurance of the precision parts of several industrial fields. Waviness may occur on the surface of the machined parts due to the table motion error and the dynamic cutting mechanism between the tool and the workpiece. The waviness may fall off the form accuracy of the precision machine parts. In the research, a micro cutting device with piezoelectric actuator has been developed to control precise depth of cut and compensate the waviness on the surface of the workpiece. Experiments have been carried out in the precision lathe. The characteristics of the surface profile and cause of the waviness profile have been analyzed and waviness profiles of some cause have been compared with those of experiments.