• Journal of Periodontal and Implant Science
• /
• 제23권3호
• /
• pp.493-506
• /
• 1993

실패한 임프란트를 구강내에 유지하기 위하여는 임프란트 매식체의 표면을 처치하여 세균독소를 제거하구 주위의 연, 경조직에 적합한 표면 구조를 만들어 주어야 한다. 이에 본 연구에서는 임프란트 매식체 표면을 high speed diamond bur, low speed diamond bur, stone, rubber point, Jetpolisher로 처치하여 가장 평활한 표면을 만들 수 있는 방법을 알아 보았다. 조도측정기를 이용하여 표면의 최대높이값을 측정한 결과 high speed diamond bur, rubber point, Jetpolisher를 사용한 시편의 최대높이값의 평균은 $7.77{\mu}m$였고, low speed diamond bur, rubber point, Jetpolisher를 사용한 경우에는 $8.44{\mu}m$를 보였다. Stone, rubber point, Jetpolisher를 사용한 경우 $6.24{\mu}m$로 가장 평활한 표면을 보였다. 이러한 수치들은 제거하지 않은 TPS(titanium plasma sprayed)면의 $24.43{\mu}m$에 비하여는 낮은 수치를 보였다. 주사전자현미경으로 관찰 하였을 때 high speed diamond bur, rubber point, Jetpolisher를 사용한 군에서는 TPS 입자들이 부분적으로 남아있었으나 이 입자들은 그 높이가 원래의 TPS에 비하여는 상당히 감소되어 있었다. Low speed diamond bur, rubber point, Jetpolisher를 사용한 시편에서는 전 표면에 걸쳐 TPS가 남아있는 거친 표면 구조를 보였다. Stone, rubber point, Jetpolisher를 사용한 시편은 대부분의 TPS가 제거되어 titanium이 노출되어 있었고, titanium 금속에 stone에 의한 흠들이 보였으나 일부분에서는 TPS가 남아있어 제조회사에서 만들어진 평활한 표면에 비해서는 거친 양상을 보였다.

• Journal of Periodontal and Implant Science
• /
• 제23권1호
• /
• pp.77-96
• /
• 1993

정상치아와 이환치아 및 구연산에 의하여 탈회한 치근면에대한 치주인대세포의 부착상태를 비교관찰 하기 위하여 정상치아와 이환치아를 취하여 정상군, 이환치근의 치근면활택술군 및 구연산처리군으로 분류하고 시험관적 실험을 통하여 관찰하였다. 세포부착실험전 각 군의 치근면의 형태를 주사전자현미경을 이용하여 관찰하였으며, 사람의 정상소구치에서부터 얻어진 치주인대세포를 배야하여 각 군의 절편을 함유한 조직배양기에 ml당 $4.5{\times}\;10^4$개의 세포를 가진 배양액 1ml씩을 넣고 동일조건하에서 30분, 1시간, 2시간, 6시간, 12시간 및 24시간 동안 배양한 후 세포의 부착이 일어난 후 상태를 주사전자현미경을 이용하여 관찰하였고, 세포증식정도를 알아보기 위하여 각 절편에 $5{\times}10^4$개의 세포가 함유된 배양액 1ml씩을 넣고 6시간동안 배양 후, 새 배양기에 옮기고 24, 48, 72시간동안 배양하여 trypsin 처리로 세포를 분리시킨 후 광학위상차 현미경을 이용, 치근단위면적당 증식된 세포수를 측정하여 다음과 같은 결과를 얻었다. 세포부착실험전 각 군의 치근면 형태를 관찰하였을 때 구연산처리군에서는 교원섬유의 노출부위라고 여겨지는 미세한 돌출구조들을 관찰할 수 있었으며 상아세관의 노출부위라고 여겨지는 함몰양상이 치근활택술군에 비하여 현저하였고 정상치아군에서는 이러한 양상을 관찰할 수 없었다. 실험 각 군 및 대조군 사이에서 세포들의 형태적인 차이점은 분명하지 않았으나 구연산처리군에서 다른 군들보다 초기의 세포부착양상이 다소 빠르게 진행 됨이 관찰되었다. 세포배양 개시 후 6시간이 경과 한 후에는 모든 군에서 공히 세포의 형태가 초기의 구형의 형태에서 편평한 세포의 형태로 변화되기 시작함이 관찰 되었고 24시간 이후에는 모든 군에서 세포들이 치근면에 납작하게 부착되고 일반적인 섬 유아세포의 형태로 변화되어 셰포의 전개가 완성된 양상이 보였다. 세포증식율의 실험에서는 24시간 후 증식된 세포 수는 치근면활택술군에서 가장높게 나타났으며 정상군에서 가장 낮은 수치를 보였으며 48시간 및 72시간후 측정에서는 구연산처리군이 다른 군들에 비해 더 많은 수의 세포증식을 관찰할 수 있었으며 각 군간의 차이는 통계학적으로 유의하였다.

• 동의생리병리학회지
• /
• 제23권1호
• /
• pp.97-103
• /
• 2009

The status and the property of a tongue are the important indicators to diagnose one's health like physiological and clinicopathological changes of inner organs. However, the tongue diagnosis is affected by examination circumstances like a light source, patient's posture, and doctor's condition. To develop an automatic tongue diagnosis system for an objective and standardized diagnosis, classifying tongue coating is inevitable but difficult since the features like color and texture of the tongue coatings and substance have little difference, especially in the neighborhood on the tongue surface. The proposed method has two procedures; the first is to acquire the color table to classify tongue coatings and substance by automatically separating coating regions marked by oriental medical doctors, decomposing the color components of the region into hue, saturation and brightness and obtaining the 2nd order discriminant with statistical data of hue and saturation corresponding to each kind of tongue coatings, and the other is to apply the tongue region in an input image to the color table, resulting in separating the regions of tongue coatings and classifying them automatically. As a result, kinds of tongue coatings and substance were segmented from a face image corresponding to regions marked by oriental medical doctors and the color table for classification took hue and saturation values as inputs and produced the classification of the values into white coating, yellow coating and substance in a digital tongue diagnosis system. The coating regions classified by the proposed method were almost the same to the marked regions. The exactness of classification was 83%, which is the degree of correspondence between what Oriental medical doctors diagnosed and what the proposed method classified. Since the classified regions provide effective information, the proposed method can be used to make an objective and standardized diagnosis and applied to an ubiquitous healthcare system. Therefore, the method will be able to be widely used in Oriental medicine.

• 한국의류학회지
• /
• 제17권2호
• /
• pp.233-245
• /
• 1993

This study was undertaken to develop the artificially soiled cloth using clay and dyed oleic acid as model soil and to evaluating the detergency by determination of K/S value and chemical analysis. The results obtained were as follows : 1. Correlation were determined between the K/S value and chemical analysis data for the detergency of developed model soil at various conditions and it was found that model soil could be extensively used for the washing examination. 2. The surface reflectance of soiled cloth with clay-oleic acid mixture was measured two wave length band that was converted K/S values and the amount of two components was individually calculated. Positive correlation were found between detergency that obtained from chemical anlysis and K/S values. Therefore, proposed method of soiled cloth with clay-oleic acid mixed soiles could be extensively used for detergency experiment. 3. The attached state of soil of on the artificially soiled cloth which was observed under a scanning electronic microscope showed a different pattern by the sort of soil. And the difference of attached state of soil had great influence upon the detergency. 4. The composition of clay was changed and formated of noncrystalinity was vanished by calcined at $800^{\circ}C$. Because of a noncrystalline of clay, artificially soiled cloth could be prepared more uniformly but the detergency was decreased.

• Journal of Welding and Joining
• /
• 제32권4호
• /
• pp.26-33
• /
• 2014

The metallurgical and mechanical characteristics, toughness and corrosion resistance of dissimilar welds between super duplex stainless steel UNS S32750 and carbon steel ASTM A516Gr.70 have been evaluated. Three heat inputs of 21.12, 24.00, 26.88kJ/cm were employed to make joints of dissimilar metals with flux cored arc welding(FCAW). Based on microstructural examination, vermicular ferrite was formed in the first layer of weld at low heat input(21.12kJ/cm) and $Cr_{eq}/Ni_{eq}$ of 1.61 while acicular ferrite was formed in last layer of weld at high heat input(26.88kJ/cm) and $Cr_{eq}/Ni_{eq}$ of 1.72. Ferrite percentage in dissimilar welds was lowest in the first layer of weld regardless of heat inputs and it gradually increased in the second and third layers of weld. Heat affected zone showed higher hardness than the weld metal although reheated zone showed lower hardness than weld metal due to the formation of secondary austenite. Tensile strengths of dissimilar welds increased with heat input and there was 100MPa difference. The corrosion test by ferric chloride solution showed that carbon steel had poor corrosion resistance and pitting corrosion occurred in the first layer(root pass) of weld due to the presence of reheated zone where secondary austenite was formed. The salt spray test of carbon steel showed that the surface only corroded but the amount of weight loss was extremely low.

• 한국어류학회지
• /
• 제21권3호
• /
• pp.208-213
• /
• 2009

긴몰개 Squalidus gracilis majimae 백색증 개체가 자연에서 발견되어 조직학적 분석을 통해 정상개체와의 차이를 비교하였다. 백색증 개체는 정상 개체에 비해 체색의 발현이 이루어지지 않았다. 등, 체측, 배, 미병부 상부, 미병부 하부, 등 뒷지느러미 및 안구조직에 대한 조직형태에서는 정상과 백색증 개체간 차이가 없었으나 멜라닌 색소의 분포 및 발현량에서 차이를 보였다. 정상 개체의 경우, 멜라닌 색소는 배쪽을 제외한 모든 부위에서 잘 발달한 모습을 볼 수 있었다. 그러나 백색증 개체의 경우, 멜라닌 색소는 눈과 몸통의 위쪽부위에서 매우 희미하게 관찰되었고, 아래쪽 부위(배, 미병부 하부, 뒷지느러미)에서는 전혀 발견되지 않았다. 이러한 멜라닌 색소의 분포는 빛과 연관이 있을 것으로 추측되었다.

• 한국자원식물학회지
• /
• 제32권6호
• /
• pp.730-734
• /
• 2019

Cryopreservation is one of the ideal and suitable methods for long-term storage of plant germplasm. The plant contaminated with diseases and pathogens are decreased the multiplication rate, survival rate and high quality of plants after cryopreservation. The aim of this work was to improve a micropropagation method for lily in Korea, which is indigenous plant. In the last process of rinsing scales after surface-sterilization, we tried to control the diseases and pathogens lived within the tissue by rinsing in 0.03% sodium hypochlorite (NaClO) instead of sterile distilled water. Bulb scales of Lilium were cultured in vitro on MS medium supplemented with Plant Preservative Mixture (PPM). The results showed that L. tsingtauense accessions were observed ranged from 53.9 to 100% with a mean value of 76.8% and L. hansonii accessions were checked from 84.5 to 85.5% with a mean of 85% survival rate. The newly small bulb formed from bulb-scales was transferred to MS medium. We checked the presence of microorganisms and survival rate after 3 weeks in culture after examination of bacterial incidences. The results indicated that the non-contamination rate were shown ranged from 75.0 to 94.1% with mean value of 83.2% in L. tsingtauense species, and that L. hansonii were observed 85.1 to 91.7% with mean value of 88.4%. This study will provide a valuable basis for establishment of effective axenic cultures for in vitro micropropagation of Korean native lily species.

• 도시과학
• /
• 제6권2호
• /
• pp.17-27
• /
• 2017

최근, 하천의 수질오염 및 악취발생으로 민원이 증가하여 하천환경개선에 큰 관심이 모아지고 있다. 본 연구의 목적은 하수 유입부에 대해 무인항공기(UAV)를 활용하여 RGB 및 적외 열 영상을 획득하고 하천제방 정비 계획 및 하천 오염 현황의 모니터링을 위한 응용성을 검토하였다. 특히, 하천 인근 공장에서 배출되는 폐수를 적외 열 영상으로 검출하여 폐수의 전파를 모니터링하였다. 또한 하천 제방 정비대상 지역과 인근지역에 대한 RGB영상을 SfM(Structure from Motion)기반 영상 해석을 통해 고정밀 3차원 모형을 제작하고 정확성을 검토하였다. 연구결과, UAV영상을 활용, 폐수유입에 따른 하천의 온도변화를 감지하여 수질오염의 유입부 및 전파 현상을 모니터링 할 수 있었다. 또한 고정밀 3차원 모델(수치지형도, 정사영상)을 제작, 정확성을 검토하고 하천의 제방정비를 위한 정밀 3차원 정보 및 식생 피복정보를 도출할 수 있었다.

• 한국압력기기공학회 논문집
• /
• 제6권1호
• /
• pp.37-42
• /
• 2010

The stay cylinder weld at the steam generator of Korean Standard Nuclear Power Plants is safety class I component and is subjected to be inspected by the volumetric examination such as ultrasonic method. As accessibility of this area is limited due to the narrow space and high radiation, the existing manual inspection method involves various difficulties. Moreover operators may be exposed to internal contamination by contaminated dust during the surface buffing process to improve the inspection reliability of this area. Recently the new automatic inspection system for stay cylinder welds has been developed. The inspection system basically consists of a driving assembly, data acquisition device and signal processing units. The driving assembly is classified by 1) the scanner for inspecting and buffing the weld, 2) pillars for guiding the scanner and 3) the base frame for loading and supporting pillars. The scanner has 4 sensor modules to inspect in 4 refracted angles and 4 incident directions. These components can be inserted into the skirt of the stay cylinder through the manway hole and assembled easily by one-touch in the skirt. Data acquisition device and signal processing units developed in previous works are also newly upgraded for better processing of data analysis and evaluation. The system has been successfully demonstrated not only in the mock-up but also in the field. In this paper, newly developed inspection system for the stay cylinder weld of the steam generator is introduced and their field applications are discussed.

• 대한기계학회논문집
• /
• 제19권4호
• /
• pp.968-980
• /
• 1995

Al/Al$_{2}$O$_{3}$/C hybrid metal matrix composites are fabricated by the direct squeeze infiltration method. From the microstructure of Al/Al$_{2}$O$_{3}$/C composites, uniform distribution of reinforcements and good bondings are found. Optimum processing conditions for preforms and squeeze castings are suggested. Mechanical properties, such as elastic modulus, elongation, 0.2% offset yield strength and ultimate tensile strength are obtained. Through the abrasive were test and wear surface analsis, wear behavior and its mechanism of AC2B aluminum and Al/Al$_{2}$O$_{3}$/C composites can be characterized under various sliding speed conditions. Tensile strenght elongation of Al/Al$_{2}$O$_{3}$/C composites are decreased with increasing the addition of carbon fiber. On the contrary, elastic modulus of Al/Al$_{2}$O$_{3}$/C composites is slightly improved compared with that of the unreinforced matrix alloy. The addition of carbon fiber to al/al$_{2}$O$_{3}$/C composites gives rise to improvement of the wear resistance. Specially, carbon chopped fibers play an important role in interfering sticking between the counter material and metal matirix composites. Al/Al$_{2}$O$_{3}$/C composites are suitable to high speed due to solid lubication of carbon. And wear model of Al/Al$_{2}$O$_{3}$/C composites is suggested by the examination of worn surfaces.