• Journal of the Korean Institute of Telematics and Electronics
• /
• v.23 no.4
• /
• pp.490-497
• /
• 1986

The effectiveness of field plate and window tapering in reducing the maximum surface electric field of planar pn junctions has been studied by two dimensional computer simulation. The influence of silicon dioxide insulator thickness is also presented.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.27 no.7
• /
• pp.843-850
• /
• 2003

Cu/PET film composites were prepared by electroless copper plating method. In order to improve adhesion between electroless plated Cu layer and polyester (PET) film, the effect of pretreatment conditions such as etching method, mixed catalyst composition were investigated. Chemical etching and plasma treatment increased surface roughness in decreasing order of Ar＞HCl＞O$_2$＞NH$_3$. However, adhesion of Cu layer on PET film increased in the following order: $O_2$＜Ar＜HCl＜NH$_3$. It indicated that appropriate surface roughness and introduction of affinitive functional group with Pd were key factors of improving adhesion of Cu layer. PET film was more finely etched by HCI tolution, resulting in an improvement in adhesion between Cu layer and PET film. Plasma treatment with NH$_3$produced nitrogen atoms on PET film, which enhances chemisorption of Pd$^{2+}$ on PET film, resulting in improved adhesion and shielding effectiveness of Cu layer deposited on the Pd catalyzed surface. Surface morphology of Cu plated PET film revealed that Pd/Sn colloidal particles became more evenly distributed in the smaller size by increasing the molar ratio of PdCl$_2$; SnCl$_2$from 1 : 4 to 1 : 16. With increasing the molar ratio of mixed catalyst, adhesion and shielding effectiveness of Cu plated PET film were increased.d.

• 보존과학연구
• /
• s.24
• /
• pp.81-98
• /
• 2003

The biodeterioration on Iksan Mireuksaji pagoda has been studied with fucus on application of K201 as a chemical treatment. Total of 39species, including 10 algae, 16 lichens, 6 mosses and 7 unidentified bacteria and fungi, were collected and identified on the surface of the pagoda. Most of them caused serious discoloration on the surface. The effectiveness and stability of K201 was examined by applying it on some part of the pagoda. A mild spraying of solution diluted to half of original reagent was good enough to eliminate all the deteriorating species on the surface. Most of discoloration disappeared after the treatment except the red color caused by iron substance. The effectiveness of the regent was compared with water wash. The stone was first washed with water and the dirt on the surface was scrubbed off from the surface. The initial surface of the stone was clearer in water wash. However, many of the deteriorating species reappear in 4 weeks after water wash. Although spraying of the reagent K201 could noteliminate all the remnant of dead organisms as good as scrubbing the surface, no deteriorating algae or lichen was observed until two month after treatment. Therefore, spraying method with chemicals seems more stable and reliable way to remove the biodeterioration than physical scrubbing of the surface.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1564-1569
• /
• 2007

This study concerns an advanced NURBS surface reconstruction method, which is based on the NURBS surface model fitting to the unstructured point cloud measured from an arbitrary complex shape. The concept of generating a simple triangular mesh model was introduced to generate a quadrilateral mesh model well-representing the topological characteristics of point cloud. The NURBS surface reconstruction processes required the use of the various methodologies such as QEM algorithm, merging scheme of pair-wise triangular mesh, creation algorithm of $G^1$ continuous tensor product NURBS surface patch, and so on. The effectiveness and reliability of the proposed NURBS surface reconstruction method were validated through the simulation results for the geometrically and topologically complex shapes.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.23 no.5
• /
• pp.577-586
• /
• 1999

Two problems with jet injection through the cylindrical film cooling hole are 1) penetration of jet into mainstream rather than covering the surface at high blowing rates and 2) nonuniformity of the film cooling effectiveness in the lateral direction. Compound angle injection is employed to reduce those two problems. Compound angle injection increases the film cooling effectiveness and spreads more widely. However, there is still lift off at high blowing rates. Shaped film cooling hole is a possible means to reduce those two problems. Film cooling with the shaped hole is investigated in this study experimentally. Film cooling hole used in present study is a shaped hole with conically enlarged exit and Inlet-to-exit area ratio is 2.55. Naphthalene sublimation method has been employed to study the local heat/mass transfer coefficient and film cooling effectiveness for compound injection angles and various blowing rates around the shaped film cooling hole. Enlarged hole exit area reduces the momentum of the jet at the hole exit and prevents the penetration of injected jet into the mainstream effectively. Hence, higher and more uniform film cooling effectiveness values are obtained even at relatively high blowing rates and the film cooling jet spreads more widely with the shaped film cooling hole. And the injected jet protects the surface effectively at low blowing rates and spreads more widely with the compound angle injections than the axial injection.

• 한국전산유체공학회:학술대회논문집
• /
• 2009.11a
• /
• pp.228-230
• /
• 2009

The moment-of-fluid (MOF) method is a new volume-tracking method that accurately treats evolving material interfaces. Based on the moment data (volume and centroid) for each material, the material interfaces are reconstructed with second-order spatial accuracy in a strictly conservative manner. The MOF method is coupled with a stabilized finite element incompressible Navier-Stokes solver for two fluids, namely water and air. The effectiveness of the MOF method is demonstrated with a free-surface dam-break problem.

• 제어로봇시스템학회:학술대회논문집
• /
• 1990.10a
• /
• pp.175-180
• /
• 1990

Rotational-free-surface (RFS) is a special type of free surface whose two boundaries coincide. For NC machining of PFS, a rotational axis as well as three Cartesian axes are required. In this paper, we develop a four-axis CAM module consisting of: a) Geometric modeling of RFS, b) CL-data generation, and c) Graphic simulation of machining operation. To test the validity and effectiveness of the developed module, several test cuts are made with Bridgeport CNC milling machine and compared with the graphic simulation.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2002.10a
• /
• pp.181-185
• /
• 2002

The modeling of realistic water-jet geometry is needed in order to facilitate the design modifications. The present paper proposes a method of generating inlet geometry. Inlet duct was represented by NURBS method which utilized the skinning and local cubic interpolation scheme. Three test examples are presented demonstrating the effectiveness of the methods of skinning and local cubic interpolation. Computational examples associated with practical configurations have shown the usefulness of the present method.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.37 no.2
• /
• pp.62-69
• /
• 2014

The capability and cost effectiveness of UUV and USV bring to underwater survey, target detection and identification operations have been widely demonstrated and accepted in recent years. Future USV systems may deploy UUVs to gain the advantage of higher area coverage rates through multiple and simultaneous operations. In this paper, we present an architecture of USV and UUV for mine countermeasure with results of measures on effectiveness.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.14 no.5
• /
• pp.365-376
• /
• 2002

An experimental study has been conducted to measure the local film-cooling effectiveness and the heat transfer coefficient for a single row of rectangular-shaped holes. four different cooling hole shapes such ai a straight rectangular hole, a rectangular hole with laterally expanded exit, a circular hole and a two-dimensional slot are tested. A technique using thermochromic liquid crystals determine adiabatic film cooling effectiveness values and heat transfer coefficients on the test surface. Both film cooling effectiveness and heat transfer coefficient are measured for various blowing rates and compared with the results of the cylindrical ho1es and the two-dimensional slot. The flow patterns downstream of holes are calculated numerically using a cummercial package. The results show that the rectangular hopes provide better peformance than the cylindrical holes. For the rectangular holes with expanded exit, the penetration is reduced significantly, and the higher and more uniform cooling Peformance is obtained even at relatively high blowing rates.