• 대한기계학회논문집
• /
• 제16권5호
• /
• pp.873-882
• /
• 1992

본 연구에서는 축대칭 형상의 하이드로 미케니칼 디프드로잉 공정을 강소성 유한요소법으로 해석하는 것이다. 본 논문에서는 Fig.1에서 보이는 바와 같은 경우 에 대하여 평두 펀치(flat headed punch)를 사용한 공정을 강소성 유한요소법으로 해 석하였으며 펀치 행정에 따른 챔버내의 압력 및 플랜지부의 압력분포를 구하였다. 접촉부의 처리는 플랜지부의 압력분포를 구하였다. 접촉부의 처리는 Yang등이 제안 한 방법을 적용하였다. 이론해석의 타당성을 알아보기 위하여 금형을 설계, 제작하 고 실험을 수행하여 결과를 비교 검토하였다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2002년도 춘계학술대회 논문집
• /
• pp.58-61
• /
• 2002

A new concept of dieless sheet forming technology is proposed in this study to overcome the drawback of conventional dieless forming technology. For this purpose, dual points contact of the conventional punch system, which is a primary cause of surface defects, is replaced to single point contact using technology combined with fluid forming. It is expected that the advanced system may lead to easy displacement control of multi-punch elements, reducing surface defects, and increasing decision and forming limits. The reduced number of punch elements also saves the cost of the equipment. In addition, the new technology can be utilized for deep drawing as well as two- or three-dimensional curved surface forming, and thereby become multi-functional and multi-purpose differently from the conventional technology.

• 한국표면공학회지
• /
• 제36권5호
• /
• pp.398-405
• /
• 2003

The stainless steel wire requires good corrosion resistance and mechanical properties, such as drawing ability, combined with a high resistance to corrosion. For increasing drawing ability of stainless steel, Ni coating methods have been used in this study. However, there is no information on the electrochemical corrosion behavior of drawed wires after Ni coating. To investigate corrosion resistance and mechanical property of drawed wire, the characteristics of Ni coated wires have been determined by tensile strength tester, hardness tester, field emission scanning microscope, energy dispersive x-ray analysis and potentiodynamic method in 0.1 M HCl. The drawed stainless steel wires showed the strain-induced martensitic structure, whereas non-drawed stainless steel wire showed annealing twin in the matrix of austenitic structure. The hardness and tensile strength of drawed stainless steel wire were higer than that of non-drawed stainless steel wire. Electrochemical measurements showed that, in the case of drawed stainless steel o ire after Ni coating, the corrosion resistance and pitting potential increased compared with non-coated and drawed stainless steel wire due to decrease in the surface roughness.

• 대한기계학회논문집
• /
• 제12권1호
• /
• pp.173-182
• /
• 1988

A program for drawing of penetrating lines was developed in personal computer. PROLOG, a language of Artificial Intelligence, was used and a data structure using relational data base was designed. An algorithm for finding the penetrating lines in the real space was developed. The program can be applied at any types of penetrating problems like curve-surface, surface-surface, curve-object, surface-object, object-object, etc. In developing the program, the following results were obtained. (1) Relational data base built in PROLOG and the function of backtracking are helpful in Computer Graphics. (2) In spite of increasing the number of edges, assigning direction to the edges makes it possible to represent the polygon meshes as the non ordered sets of directional half edges. (3) Topologicaly the penetrating lines of a polygon can be represented as the edge-pairs in the edge list of the polygon,

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 1999년도 춘계학술발표회 초록집
• /
• pp.36-37
• /
• 1999

• The Journal of Korean Physical Therapy
• /
• 제24권1호
• /
• pp.1-6
• /
• 2012

Purpose: The grip strength is influenced by various factors, such as position of the upper extremity, characteristics of the hand, and general physical condition. In this study, we investigated whether abdominal muscle activity in combination with the abdominal drawing-in maneuver has any effect on the grip strength in healthy young adults. Methods: This study included 31 healthy subjects (16 males, 15 females). We used surface electromyography and pressure bio-feedback unit for this experiment. All Subjects were placed in a cock-lying position with comfort and the grip strength was measured. On the following day, the pressure bio-feedback unit was placed beneath their fifth lumbar vertebra, and the, grip strength was measured again. This time, the measurement was taken while drawing-in their abdomen below the navel gently and gradually, while maintaining a neutral pelvic position. Results: The grip strength was significantly increased when subjects performed the drawing-in maneuver than when they were comfortable (p<0.05). In addition, activations of the rectus abdominal muscles significantly increased (p<0.05). Conclusion: In the current study, we found that abdominal muscle activity, in combination with the abdominal drawing-in maneuver, affected the grip strength, positively. Therefore, we suggest that this result should be considered when evaluating the grip strength.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 추계학술대회 논문집
• /
• pp.118-121
• /
• 2005

The square cup drawing of magnesium alloy AZ31 $(aluminum\;3\%,\;Zinc\;1\%)$ sheets was studied by experimental approach in various temperatures (200, 250, 300, 350, $400^{\circ}C$) when blank holding force (BHF) was controlled in real-time. And so on, the drawability was measured with the different die and punch coating. The square cup drawing test was performed by three different coated punches (CrN, TiCN, Non-coated). BHF was set about 2.0 KN, forming speed was 50 mm/min, blank thickness were 0.5, 1.0mm and the cup size was 40 mm by 60 mm after forming. The experimental data of square cup drawing test show that the tools coating and temperature were effect on the drawbility.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 제5회 압연심포지엄 신 시장 개척을 위한 압연기술
• /
• pp.91-97
• /
• 2004

The drawbead is one of the most important factors in sheet metal forming for automotive parts. So clarifying the friction characteristics between sheets and drawbead is essential to improve the formability of sheet metal. Therefore in this study, drawbead friction test was performed at various bead materials(FC300, HC891, FCD550, HD700, HK600, HK700, SKD11) and surface treatment of beads(Base, induction hardening, Cr plating, ion nitriding, Toyoda diffusion process, TiCN, TiN, CrN). Circular shape bead has been used for the test. The results show that friction and drawing characteristics were mainly influenced by surface treatment.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 추계학술대회논문집
• /
• pp.48-53
• /
• 2004

Injection molded plastic parts have many surface defcts: Warpage, wedline, flowmark, zetting, scratching, shading and so on. In the desktop mnitor's case, Weld line have been one of the main surface defects. Nowadays in the pursuit of light weight of parts, one of the big problems of LCD Monitor thinks Warpage and surface shrinkage. In this paper, we introduce some instances for prevevting these defestcs in the side of mould drawing, parts drawing and processing condition. Based on these, we tried to find out the optimum processing conditions through repeatedly tried injection moulding after reflecting these instances.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 추계학술대회 논문집
• /
• pp.418-422
• /
• 2005

In this study, the die design and die series on the surface residual stress of cold drawn eutectoid steel wire has been investigated. Test pieces were fabricated using die series with different mean and final reduction ratio. Surface residual stresses in the axial direction were measured by X-ray diffraction, Broker's 2-dimensional GADDS system. Results were compared with stress profiles which were calculated by 3D and 2D finite element simulation, Hibbitt's ABAQUS 6.4 program in Finite Element Analysis. By means of FEA method, optimal die shape considering delta-parameter were induced and applied in order to determine die sequence designs. Balance of the drawing stresses was also introduced to optimize die sequence.