• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2007년도 제34회 KOSCO SYMPOSIUM 논문집
• /
• pp.19-24
• /
• 2007

The deposition behavior of soot particles in a diffusion flame along a solid wall was examined experimentally by getting rid of the effect of natural convection utilizing microgravity environment. The microgravity environment was realized by using a drop tower facility. The fuel for the flame was an ethylene ($C_2H_4$) and the surrounding oxygen concentration 35% with the surrounding air velocity of $V_a$=2.5, 5, and 10 cm/s. Laser extinction method was adopted to measure the soot volume fraction distribution between the flame and burner wall. The results show that observation of soot deposition in normal flame was difficult from buoyancy and the relative position of flame and solid surface changes with time. The soot particle distribution region moves closer to the surface of the wall as the surrounding air velocity is increased. And the experiments determined the trace of the maximum soot concentration line. It was found that the distance between soot line and flame line is around 5 mm. That is, the soot particle near the flame zone tends to move away from flame zone because of thermophoretic force and to concentrate at a certain narrow area inside of the flame, finally, to adhere the solid wall.

• 한국전기전자재료학회논문지
• /
• 제14권10호
• /
• pp.828-834
• /
• 2001

Zinc oxide (ZnO) films deposited on indium (In) films were post-annealed in a rapid thermal anealing (RTA) system. The ZnO/In films were RTA-treated in air or a vacuum ambient. The crystallographic properties and surface morphologies of the films were studied before and after the RTA by X-ray diffraction(XRD) and scanning electron microscopy (SEM), respectively. The resistivity variation of the films with RTA temperature and time was measured by the 4-point probe method. Auger electron spectroscopy (AES) was carried out to figure out the redistribution of indium atoms in the ZnO films. The resistivity of the ZnO/In films decreased to 2$\times$10$\^$-3/ Ωcm by diffusion of the In. The In diffusion into the ZnO films roughened the surface of ZnO films. The results of depth profile by AES showed a hump of In atoms around ZnO/In interface after the RTA at 800 $\^{C}$. The effects of temperature time and ambient during the RTA on the structural and electrical properties of the ZnO/In films were discussed.

• Membrane and Water Treatment
• /
• 제11권4호
• /
• pp.237-245
• /
• 2020

The effects of the mixed two solvents, Dimethylacetamide (DMAc) and Dimethylformamide (DMF), and Polyethylene glycol (PEG) and Polyvinylpyrrolidone (PVP) as additives on performance of Polyvinylidene fluoride (PVDF) membranes were studied. Initially, PEG200 was used as a primary additive at fixed percentage of 5% wt. PVP was then blended with PEG200 in different concentrations. PVDF and DMAc were used as polymer and solvent in the casting solutions, respectively. To control the diffusion rate of PVP in the presence of PEG200 and PVP blend, mixtures of DMAc and DMF were used as the mixed solvent in the casting solutions. Asymmetric PVDF membranes were prepared via phase inversion process in a water bath and the effects of two additives and two solvents on the membrane morphology, pure water flux (PWF), hydrophilicity and rejection (R) were investigated. Attenuated Total Reflection Fourier Transform Infrared Spectra (ATR-FTIR) analysis was used to show the residual PVP on the surface of the membranes. Atomic Force Microscopy (AFM) was utilized to determine roughness of membrane surface. The use of mixed solvents in the casting solution resulted in reduction of PVP diffusion rate and increment of PEG diffusion rate. Eventually, PWF and R values reduced, while porosity and hydrophilicity increased.

• 대한기계학회논문집B
• /
• 제28권5호
• /
• pp.501-509
• /
• 2004

Unipolar diffusion charging of non-spherical particles was investigated for various particle shapes. We researched with TiO$_2$agglomerates produced by the thermal decomposition of titanium tetraisopropoxide (TTIP) vapor. TTIP was converted into TiO$_2$, in the furnace reactor and was subsequently introduced into the sintering furnace. Increasing the temperature in the sintering furnace, aggregates were restructured into higher fractal dimensions. The aggregates were classified according to their mobility using a differential mobility analyzer. The projection area and the mass fractal dimension of particles were measured with an image processing technique performed by using transmission electron microscope (TEM) photograph. The selected aggregates were charged by the indirect photoelectric-charger and the average number of charges per particle was measured by an aerosol electrometer and a condensation particle counter. For the particles of same mobility diameter, our results showed that the particle charge quantity decreases as the sintering temperature increases. This result is understandable because particles with lower fractal dimension have larger capacitance and geometric surface area.

• 한국기계가공학회지
• /
• 제16권4호
• /
• pp.46-52
• /
• 2017

We quantitatively measured the mass transfer from friction surfaces, specifically brake pads and rotors, using laser plasma spectroscopy. Specifically, we modelled the mass transfer from the pad to the rotor and measured the elemental diffusion intensity distribution in the rotor material using laser plasma spectroscopy. The main elements measured were Cu, Ni, Ti, and Cr, and the distribution of these after transfer was measured as the ratio of the atomic peak and the ion peak of the plasma in the rotor exposed to friction and the surface composition of the rotor and the roughness, respectively. We measured and quantified the diffusion coefficient for each element through the mass transfer model and found that Cr obtained the largest diffusion coefficient (D) of the elements measured based on this system with a value of $1.9484{\times}10^{-15}m^2/s$.

• 대한기계학회논문집B
• /
• 제37권11호
• /
• pp.977-984
• /
• 2013

흡착식 제습기에 적용되는 제습 로터는 높은 제습 성능을 달성키 위해, 흡수율이 높은 재질로 구성된 수많은 미세 채널을 포함하고 있다. 본 연구에서는 습공기 흐름에 의해 나타나는 제습 로터 내부의 반복적인 흡착/탈착 과정에 대한 수치해석 결과를 소개한다. 수치해석의 정확도와 효율성을 고려하여 흡습층 내부에서는 표면 확산(surface diffusion)만을 고려하여 해석을 수행하였다. 해석결과는 이전의 연구와 비교하였고, 온도에 대한 비교 오차는 약 2%이하인 점을 감안하여 해석결과가 매우 잘 일치하는 것을 확인하였다. 단일 채널 내부에서 유동층 (flow layer)과 흡습층 (desiccant layer) 간 열/물질전달 연계 해석을 통하여 채널 내부의 수증기 분율, 흡수된 물 분율과 온도 등에 대한 시간 및 공간적 변화를 나타내었다.

• 한국수소및신에너지학회논문집
• /
• 제25권4호
• /
• pp.386-392
• /
• 2014

The effective water management in a polymer electrolyte membrane fuel cell (PEMFC) is one of the key strategies for improving cell performance and durability. In this work, an ex situ measurement was carried out to understand the water droplet behavior on the surface of gas diffusion layer (GDL) as a fundamental study for establishing novel water management. For that purpose, simplified cell including one rib and two flow channels was designed and fabricated. Using this ex situ device, the water droplet emergence through the GDL of the PEMFC was emulated to understand liquid water transport through the porous diffusion medium. Through the visualization experiment, the emergence and growth of water droplets at the channel/GDL interface are mainly observed with the surface characteristics of GDL (SGL 10BA, 24BA) and rib when the liquid water passes through the GDL and is expelled to the flow channel. It is expected that the results obtained from this study can contribute to the better understanding on the water droplet behavior (emergence and removal) in the flow channels of PEMFC.

• 한국전기전자재료학회논문지
• /
• 제12권1호
• /
• pp.35-43
• /
• 1999

Microstructures and dielectric properties of (Sr$\_$1-x/Ca$\_$x/) TiO$_3$-0.006Nb$_2$O$\_$5/ (0.05$\leq$x$\leq$0.2) boundary layer ceramics were investigated. The samples fired in a reducing atmosphere(N$_2$) were painted on the surface with CuO paste for the subsequent grain boundary diffusion, and then annealed at 1100$^{\circ}C$ for 2 hrs. The metal oxide of CuO infiltrated by thermal diffusion from surface of sample presents continuously in not grain but only grain boundary, and makes up thin boundary phase. The SEM photo, and EDAX revealed that CuO was penetrated rapidly into the bulk along the grain boundaries during the annealing. The average grain sizes is continuously increased as the content of substitutional Ca is increased from 5[mol%] to 15[mol%], but the average grain size of the sample with content of 20[mol%] Ca is slightly decreased. In the samples with content of 10∼15[mol%] Ca, excellent dielectric properties were obtained as follows; dielectric constant <25000, dielectric loss <0.3[%], and capacitance change rate as a function of temperature <${\pm}$10[%], respectively. All samples in this study exhibited dielectric relaxation with frequency as a functior of the temperature.

• 멤브레인
• /
• 제7권3호
• /
• pp.150-156
• /
• 1997

입자의 정밀여과에 있어 임계플럭스의 이론치를 계산하기 위해 확산(diffusion), 횡방향이동(lateral migration), 전단유도확산(shear induced diffusion), 그리고 입자의 정전기적 반발력에서 기인하는 상호작용에 의한 상승이동(interation enhanced migration) 등의 입자의 역전달 이동을 고려하였다. 보통의 여과조건에서 제타전위의 절대치가 20~40mV이고 직경이 0.1$\mu{m}$~10$\mu{m}$인 입자의 경우 상호작용에 의한 이동이 가장 중요한 역전달 메카니즘이었다. 입자크기에 따라 계산된 임계플럭스값을 실험적으로 확인하기 위해 다양한 크기를 갖는 구형인 적철광(hematite)입자를 합성하여 여과실험을 수행하였다. 이 실험치는 역전달 이론에 의해 예측된 플럭스의 이론치와 비교적 잘 일치하였다.

• 한국표면공학회지
• /
• 제28권5호
• /
• pp.320-328
• /
• 1995

The electroplated steel sheets were heated during the short periods(10~60 seconds) at high temperature ($360^{\circ}C$～$500^{\circ}C$) in order to investigate thermal diffusion behaviors. When the steel sheets were heated for 10 seconds, all the coated layers were alloyed at $420^{\circ}C$ but at temperature lower than $400^{\circ}C$ the $\eta$ phase partially remained on the coated surface. At higher temperature, the longer the time for heat treatment the iron contents were increased in coated layer but the glossiness and whiteness of the coated surface were decreased. While the alloying phases of $\eta$, $\zeta$, $\delta_1$ and $\Gamma$ were appeared in the coated layer at the heat treatment temperature of $360^{\circ}C$, the phase was disappeared at $420^{\circ}C$ but the rests grew in size at the temperature of $440^{\circ}C$. When the heat treatment temperature and heating time were increased, the thickness of $\Gamma$ phase was rapidly increased to 0.8 $\mu\textrm{m}$. The optimum conditions for the heat treatment to prevent powdering of coated layer were obtained to heat it for 30 seconds at $400^{\circ}C$ and 10 seconds at $440^{\circ}C$, and the iron content in coated layer was suited to be 10 percents.