• Journal of the Korean institute of surface engineering
• /
• v.25 no.5
• /
• pp.235-252
• /
• 1992

(Ti, Al)N films were deposited on 304 stainless steel sheet by D.C. magnetron sputtering using Al target and Ti plate. The high temperature oxidation of (T, Al)N films with the variation of composition has been investigated. The chemical composition of (Ti, Al)N films with the variation of composition has been investigated. The chemical composition of (Ti, Al)N films was similar to the sputter area ratio of titanium to aluminum target by means of EDS and AES survey. The high temperature oxidation test of (Ti, Al)N showed that (Ti, Al)N has better high temperature resistance than TiN and TiC films. TiC films were cracked at 40$0^{\circ}C$ in air TiN films quickly were oxidised at $600^{\circ}C$, were spalled more than $700^{\circ}C$. But (Ti, Al)N films are relatively stable to$ 900^{\circ}C$. The good resistance to high temperature oxida-tion of (Ti, Al)N films are due to the formation of dense Al2O3 and TiO2 oxide layer. Especially, Al2O3 oxide layer is more important. The results obtained from this study show, it is believe that the (Ti, Al)N film by D.C. magnetron sputtering is promising for the use of high temperature and wear resistance mate-rials.

• Korean Journal of Materials Research
• /
• v.24 no.12
• /
• pp.682-688
• /
• 2014

Physical and chemical changes in a polished wafer and in $2.5{\mu}m$ & $4{\mu}m$ epitaxially grown Si layer wafers (Epilayer wafer) after surface treatment were investigated. We characterized the influence of surface treatment on wafer properties such as surface roughness and the chemical composition and bonds. After each surface treatment, the physical change of the wafer surface was evaluated by atomic force microscopy to confirm the surface morphology and roughness. In addition, chemical changes in the wafer surface were studied by X-ray photoemission spectroscopy measurement. Changes in the chemical composition were confirmed before and after the surface treatment. By combined analysis of the physical and chemical changes, we found that diluted hydrofluoric acid treatment is more effective than buffered oxide etching for $SiO_2$ removal in both polished and Epi-Layer wafers; however, the etch rate and the surface roughness in the given treatment are different among the polished $2.5{\mu}m$ and $4{\mu}m$ Epi-layer wafers in spite of the identical bulk structural properties of these wafers. This study therefore suggests that independent surface treatment optimization is required for each wafer type, $2.5{\mu}m$ and $4{\mu}m$, due to the meaningful differences in the initial surface chemical and physical properties.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2005.08a
• /
• pp.42-43
• /
• 2005

• Journal of the Korean institute of surface engineering
• /
• v.42 no.5
• /
• pp.197-202
• /
• 2009

The electrodeposition in acidic aqueous electrolyte bath of cadmium telluride on gold electrodes has been studied by electrochemical analysis. Conventional cyclic voltammetry using potentiostat is considered as a reliable method to study electrochemical behavior of electrodeposition of CdTe. In this paper, the mechanism of CdTe deposition and its cyclic voltammetry were studied with the Te ion concentration, temperature, potential, and scan rate. We also investigated surface morphologies using FESEM and atomic composition of Cd and Te using EDS. Atomic composition of Cd and Te were varied with Te ion concentration in the electrolyte.

• Journal of Korean Society for Atmospheric Environment
• /
• v.24 no.E2
• /
• pp.83-91
• /
• 2008

This work investigated the methodology to simultaneously optimize the ozone and relative humidity composition for the $NO_x$ degradation using soil biofilter. Experiments were made as a function of inlet ozone concentration ($0{\sim}1,770\;ppb$) and relative humidity ($38{\sim}81%$). Factorial design ($2^2+3$) and response surface methodology by central composite designs were used to examine the role of two factors and optimal response condition on $NO_x$ degradation. It was found that a second-order response surface model can properly interpret the experimental data with an $R^2$-value of 0.9730 and F-value of 71.83, based on which the maximum $NO_x$ degradation was predicted up to 92.8% within our experimental conditions.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.1
• /
• pp.130-136
• /
• 2005

Induction hardening increases hardness near the surface where it's most needed, and leaves the surface in compression which improves fatigue life. Although case depth and chemical composition are same, the structure of induction hardened shaft affects the fatigue strength and life because of austenization during hardening. Therefore torsional fatigue tests of specimens from various structures, which are obtained by nomalizing, spheriodized annealing and tempering after quenching, were conducted on induction hardened automotive drive shafts with various case depths and loads applied in order to evalute the relation between structure and fatigue strength.

• Journal of the Korean Society of Tobacco Science
• /
• v.5 no.2
• /
• pp.9-15
• /
• 1983

The effect of leaf dehydration process and air flow capacity of bulk curing on physical properties and composition of cured leaves was studied, respectively, during flue- curing. Cured leaves from excessive moisture during yellowing stage and those from rapid dehydration Process inevitably during later stages, tend towards lower equilibrium moisture contents, higher shatter index, hither protein nitrogen, and leaf scalding or deterioration of Beaves with redish cast. Early dehydration at the yellowing stage re suited in increasing of p Bamitic, stearic, linoleic, and linolenic acid contents, but showed reduction of brightness difference between upper and lower surface of the cured leaves, Leaf surface lipid decreased with the progress of curing stages, more conspicuously during later stage. Lowering air flow capacity of fan by 50oye during stem drying stage resulted in increasing of leaf surface lipid and 25oye decreasing of electric power consumption , but curing period and kerosene consumption were not affected.

• Journal of the Korean institute of surface engineering
• /
• v.43 no.5
• /
• pp.243-247
• /
• 2010

The micro Vickers hardness and internal stress of Ni-Fe metal thin film synthesized by electrodeposition method at $25^{\circ}C$ were studied as a function of bath composition, and surface microstructure and atomic compositions of thin films were investigated by SEM and EDS. And the shape change of $200\;{\AA}$ Ni-Fe nanowires made using anodic aluminum oxide(AAO) templates by electrodeposition method were observed by SEM as a function of ultrasonic treatment time and bath composition. The Fe deposition contents on the substrate non-linearly increased with Fe ion concentration over total metal ion concentration. In case of low Fe contents film, the grain size is smaller and denser than high Fe contents deposited films, and the micro Vickers hardness increased with Fe contents of electrodeposited films. These results affected the shape change of nanowire after ultrasonic treatments.

• Journal of the Korean institute of surface engineering
• /
• v.35 no.4
• /
• pp.232-240
• /
• 2002

The composition and the microstructure of the Zn-Cr alloys electroplated in chloride bath with EDTA were studied according to electrolysis conditions. The cathode current efficiency decreased with increasing both Cr/(Cr+Zn) ratio and current density. The Cr content of the alloy deposits increased with Cr/(Cr+Zn) ratio and current density The phase structure of Zn-Cr alloy deposits changed from η-Zn through η-Zn+${\gamma}$'-ZnCr to ${\gamma}$'-ZnCr with increasing Cr content of alloys. The surface morphology of Zn-Cr alloy deposits changed from fine needle shaped crystallites through the mixed structure of needle-shaped and granular one to the colony structure with fine granular crystallites according to the change of phase structure

• Journal of the Korean institute of surface engineering
• /
• v.26 no.5
• /
• pp.245-254
• /
• 1993

The effects of pulse current electrolysis conditions on the composition and the microstructure of Ag-Sn alloy were studied by using a pyrophosphate bath. Both cathode current efficiency and throwing power of alloy deposits formed under pulse plating conditions, decreased with increasing mean current density, and lower than those under D.C. electrolysis condition. Tin content of Ag-Sn alloy decreased noticebly with in-creasing the mean current density, while it increased with the increase of On-time from 1 to 10 ms. The pre-ferred orientation of Ag-Sn alloy changed with increasing cathode overpotential in the sequence of (100)longrightarrow(100)+(111)longrightarrow(111) at $20^{\circ}C$ and (110)longrightarrow(111)longrightarrow(111)+(100) at $30^{\circ}C$. The effective crystal grain size of the alloy was decreased by decreasing temperature from $30^{\circ}C$ to $20^{\circ}C$ and the surface structure of them was related to the preferred orientation.