• Transactions on Electrical and Electronic Materials
• /
• v.18 no.4
• /
• pp.199-202
• /
• 2017

Silicon carbide (SiC) is being spotlighted as a next-generation power semiconductor material owing to the characteristic limitations of the existing silicon materials. SiC has a wider band gap, higher breakdown voltage, higher thermal conductivity, and higher saturation electron mobility than those of Si. When using this material to implement Schottky barrier diode (SBD) devices, SBD-state operation loss and switching loss can be greatly reduced as compared to that of traditional Si. However, actual SiC SBDs exhibit a lower dielectric breakdown voltage than the theoretical breakdown voltage that causes the electric field concentration, a phenomenon that occurs on the edge of the contact surface as in conventional power semiconductor devices. Therefore in order to obtain a high breakdown voltage, it is necessary to distribute the electric field concentration using the edge termination structure. In this paper, we designed an edge termination structure using a field plate structure through oxide etch angle control, and optimized the structure to obtain a high breakdown voltage. We designed the edge termination structure for a 650 V breakdown voltage using Sentaurus Workbench provided by IDEC. We conducted field plate experiments. under the following conditions: $15^{\circ}$, $30^{\circ}$, $45^{\circ}$, $60^{\circ}$, and $75^{\circ}$. The experimental results indicated that the oxide etch angle was $45^{\circ}$ when the breakdown voltage characteristics of the SiC SBD were optimized and a breakdown voltage of 681 V was obtained.

• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.1234-1236
• /
• 2005

High temperature superconducting(HTS) windings for an HTS transformer which have been developed have two kinds of type, one is the layer type and the other is disk type. The disk type windings have advantages over the layer type ones for a power transformer such as good insulation and limit of voltage stress. But this kind of HTS winding generates excessive AC losses caused by strong magnetic field component perpendicular to the surface of the HTS wire. Nevertheless, the layer type windings have adopted for an HTS power transformer so far because of the small AC losses of the HTS windings. We propose a new winding method for a high voltage HTS transformer which has advantages of both type of HTS windings, and we call it continuous disk type HTS winding. This new type of HTS winding consists of pile of lots of HTS disk windings which have no resistive joint between them. A prototype of an HTS winding was fabricated by the new winding method we proposed and characteristic test was carried out. The test result shows that the new type HTS windings can be applied to HTS power transformers, especially to the high voltage ones.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.27 no.12
• /
• pp.820-824
• /
• 2014

TiNOx multi-layer thin films on aluminum substrates were prepared by DC reactive magnetron sputtering method. 4 multi-layers of $TiO_2$/TiNOx(LMVF)/TiNOx(HMVF)/Ti/substrate have been prepared with ratio of Ar and ($N_2+O_2$) gas mixture. $TiO_2$ of top layer is anti-reflection layer on double TiNOx(LMVF)/TiNOx(HMVF) layers and Ti metal of infrared reflection layer. In this study, the crystallinity and surface properties of TiNOx thin films were estimated by X-ray diffraction(XRD) and field emission scanning electron microscopy(FE-SEM), respectively. The grain size of TiNOx thin films shows to increase with increasing sputtering power. The composition of thin films has been investigated using electron probe microanalysis(EPMA). The optical properties with wavelength spectrum were recorded by UV-Vis-NIR spectrophotometry at a range of 200~1,500 nm. The TiNOx multi-layer films show the excellent optical performance beyond 9% of reflectance in those ranges wavelength.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.45 no.6
• /
• pp.30-35
• /
• 2013

To conserve wood resources for papermaking, chemical compositions of the hemp (Cannabis sativa L.) bast fiber cultivated in Korea such as holocellulose, ${\alpha}$-cellulose, lignin, alcohol-benzene extractives, hot and cold water extractives, and ash contents were investigated to manufacture the specialty packaging paper effectively. Significantly very low klason lignin content of 3.3% was accomplished by removing of the outer shell of bark. Laboratory soda pulping method which is very useful for the nonwood fiber was adapted, and it was found that there was no significant difference in both kappa number and H-factor between 25% and 30% NaOH charge. Hemp pulp cooked with the laboratory digester in 25% NaOH at $170^{\circ}C$ were mixed together with the wood pulp(NBKP:LBKP=1:1) in order to find the optimum mixture ratio which exhibited acceptable paper strength properties such as tensile index, burst index, and tear strength. When 10% of hemp soda pulps was mixed with 90% of wood pulps comprised of SwBKP and HwBKP (1:1), all physical strength increased significantly. The physical strength decreased as the amount of hemp pulp increased because the cell wall of bast fiber is very thick which causes low conformability and low fiber-fiber bonding. These results showed that paper made of hemp-wood pulp can be used for the specialty packaging paper which requires both the characteristic surface properties and the high physical strength of hemp fiber.

• Journal of the Korean Vacuum Society
• /
• v.14 no.4
• /
• pp.201-206
• /
• 2005

In this work, we tried to improve the fabrication process in HVPE (Hydride Vapor Phase Epitaxy) system by using Si(111) substrate with pre-deposited Al layer. PL measurements was done for samples with and without pre-deposited Al on Si and it was also examined the dependence of the optical characteristic properties on AlN buffer thickness for GaN/AIN/Al/Si. A sample with thin Al nucleation layer on Si substrate reveals a better optical property than the other. And it suggests that the thickness for AlN buffer layer with thin Al nucleation layer on Si(111) substrate is most proper about $260{\AA}$ to grow GaN in HVPE system. The surface morphology of GaN clearly shows the hexagonal crystallization. The XRD pattern showed strong peak at GaN{0001} direction.

• Membrane Journal
• /
• v.11 no.4
• /
• pp.170-178
• /
• 2001

PVC microfiltration membrane was prepared by phase immersion method and applied to membrane bioreactor (MBR) contained activated sludge. The hydrophilicity of membrane and the pore size increase with the amount of additive(PVP) ducting the preparation of membrane. Permeation characteristics and the membrane fouling behavior were investigated by varying the internal environment in MBR using the prepared membranes. When there is a sludge bulking in MBR caused by microorganism, membrane fouling was accumulated. The cake layer resistance, R$_{c}$, of membrane increased in the order of CP-0 > CP-1.0 > CP-1.5. Rc increased up to 3.5~7 fold where the sludge bulking occurred in MBR. CP-1.5 seems to be appropriated membrane on the basis of the surface characteristics and the flux. The average flux of all the test membrane was 12(${\pm}$2) L/$m^2$hr whereas the COD removal efficiency was 98.8%. The ratio of bulking sludge and the type and the size of microorganism in operating MBR accelerate the membrane fouling and flux decline. It is concluded that the characteristic of membrane filtration depends on the hydrophilicity of membrane, the internal environment of MBR reactor and the growth factor of sludge.

• Journal of the Korean Vacuum Society
• /
• v.9 no.3
• /
• pp.254-257
• /
• 2000

We report spectroscopic ellipsometric (SE) measurements on $Cd_{1-x}Mg_x/Te$ (0$\leq$x$\leq$0.43) films grown on GaAs substrate. When compared with previous bulk data, at first, current spectrum shows clear interference oscillations below $E_0$ band gap energy, which means the transparent characteristic of direct transition material below $E_0$ edge. It proves that the film samples used for this work have the most interrupted surface of high quality reported so far by SE. Secondly the best resolution of $E_2$-peak is observed, so we can report clear splitting of E$_2$and $E_0'$ band gap energies. We also performed the multilayer calculation necessary to remove this interference oscillations to observe $E_0'$ band gap energy of $Cd_{1-x}Mg_x/Te$ (x=0.23) film.

• Journal of Wetlands Research
• /
• v.20 no.1
• /
• pp.14-19
• /
• 2018

In this study, the method considering the influence of the high-rise building in urban rainfall-runoff analysis using SWMM was proposed. The method proposed in this study was to calculate the time of reaching the surface of the rainwater considering the size and height of the building, and to modify the basin width to reflect this. In the method proposed in this study, the concentration time considering the size and height of the building is calculated and based on this time the basin width is modified. The proposed method was verified with the experimental result of Isidoro et al. (2012). As a result, the proposed method was found to be valid since the simulated hydrograph was fairly identical to experimental result. In both hydrographs, it was confirmed that the change of the discharge characteristic, such as decrease of peak discharge and lag of peak time, over increasing density of the building was similar each other.

• Korean Journal of Soil Science and Fertilizer
• /
• v.35 no.4
• /
• pp.197-206
• /
• 2002

Volumetric soil water contents through a soil profile were monitored to identify the effects of tillage systems and soil physico-chemical characteristic on soil water movement from the soil profile. Water content profiles under no tillage (NT) and conventional tillage (CT) practices were compared at two commercial farms in central Illinois from 1992 through 1994, using neutron-scattering techniques in weekly intervals during each growing season. The volumetric water content of surface soil layers was affected more by tillage systems and rainfall amounts, whereas that of the subsoil layers was more strongly affected by soil types. Soil water percolated faster through Saybrook and Catlin soils than through Drummer, Flanagan, and Ipava soils because Saybrook and Catlin soils have lower clay content and water-retention capacity and higher permeability than Drummer, Flanagan, and Ipava soils. Increased soil organic matter (SOM) in Drummer, Flanagan, and Ipava soils would be attributable to the higher soil water retention than other soil types. Soil water contents in the corn root zone were consistently higher under CT plots than under NT plots.

• Journal of Korea Society of Industrial Information Systems
• /
• v.25 no.5
• /
• pp.83-90
• /
• 2020

In this paper, a web-based seed phenotype visualization support system is proposed to extract and visualize data such as the surface color, length, area, perimeter and compactness of seed, which is phenotype information from the image of soybean/rice seeds. This system systematically stores data extracted from seeds in databases, and provides a web-based user interface that facilitates the analysis of data by researchers using data tables and charts. Conventional seed characteristic studies have been manually measured by humans, but the system developed in this paper allows researchers to simply upload seed images for analysis and obtain seed's numerical data after image processing. It is expected that the proposed system will be able to obtain time efficiency and remove spatial restriction, if it is used in seed characterization research, and it will be easy to analyze through systematic management of research results and visualization of the phenotype characteristics.