• Journal of the korean society of oceanography
• /
• 제34권3호
• /
• pp.144-150
• /
• 1999

Slope sedimentation on the modern west Florida continental margin is controlled by pelagic carbonate accumulation and off-shelf sedimentation of neritic carbonates and terrigenous fines. Production and deposition of pelagic carbonates by planktonic foraminifera and coccoliths have played a significant role in the total slope sedimentation and are mainly promoted by sea-surface productivity. Organic carbon data reflect the relatively high biological productivity in surface waters, indicating high accumulation of biogenic calcareous sediments. The surface-water productivity in the study area is supported by the relation among microfossil assemblages, carbonate mineralogy and sedimentary organic carbon.

• 한국세라믹학회지
• /
• 제48권5호
• /
• pp.373-378
• /
• 2011

The composite added with surface-coated chopped carbon fiber showed the microstructure of a 3 dimensional discretional arrangements. The fiber reinforced reaction bonded silicon carbide composite, containing the 50 vol% carbon fiber, showed the porosity of < 1 vol%, 3-point bending strength value of 250MPa and fracture toughness of 4.5 $MPa{\cdot}m^{1/2}$. As the content of carbon fiber was increased from 0 vol% to 50 vol% in the composite, fracture strength was decreased due to the increase of carbon fiber, which has a less strength than SiC and molten Si. On the other hand, the fracture toughness was increased with increasing the amount of carbon fiber. According to the polished microstructure, carbon fiber was shown to have a random 3 dimensional arrangement. Moreover, the fiber pull-out phenomenon was observed with the fractured surface, which can explain the increased fracture toughness of the composite containing high content of carbon fiber.

• 한국정밀공학회지
• /
• 제8권4호
• /
• pp.33-40
• /
• 1991

The decrease in surface roughness of work roll and steel strip in cold rolling of low carbon steel strip has been investigated by working distance, materials, total separating force and total reduction ratio. The main results are as follows; For the same lubricating conditions. 1) The changing of surface roughness of steel strip were similar to work roll. The transcription ratio is in inverse proportion to the carbon content of steel strip. 2) The surface roughness of steel strip is hardly change according to changing of total separating force and total reduction ration. 3) The wear of work rolls surface is more rapid in that case of continuous casted steel strip than ingot casted steel strip. The aluminium content dull powder adhere on the rolls surface, and so. It makes the mirror surface of work roll accelerate.

• 한국표면공학회지
• /
• 제45권4호
• /
• pp.162-167
• /
• 2012

Ni-P/C multi-layer was synthesized by electroless plating and paste coating for better corrosion and surface conductance as a metallic bipolar plate. The Ni-P layer could be synthesized with the range of 2.6~22.4 at.% P contents and it's surface morphology and corrosion resistance depend on content of P. Corrosion resistance of the Ni-P layer in sulfuric acid by electrochemical test is similar with pure Ni. Surface resistance of pure Ni after corrosion was increased about 8% compared to pure Ni. On the other hand, that of the Ni-P/C composite with 20% carbon content was increased only 1%.

• 보존과학회지
• /
• 제20권
• /
• pp.55-65
• /
• 2007

석탑 표면 흑화현상에 영향을 끼치는 탄소를 평가하기 위하여 석탑표면의 흑색층을 분석하였다. 원소분석기를 이용하여 총탄소량을 측정하였으며. 원소탄소와 유기탄소는 시료를 산처리하여 탄산염탄소를 제거한 후 OC/EC 탄소분석기를 이용하여 분석하였다. 이들 석탑 표면 흑색시료에서 검출된 원소탄소의 함량은 0.52%로 원소탄소 자체만으로 석탑 표면의 흑화현상을 설명하기에는 충분치 않은 양이나 중요한 역할을 하는 것으로 보인다. 석탑 흑색표면 내 원소탄소의 기원을 살펴보기 위해 석탑주변의 대기미세먼지 (PM-10)를 포집하여 성분을 검토하였다. 대기미세먼지 중에서 가장 높은 비율을 차지하고 있는 것은 이온성분으로 38.4%였으며 토양지각성분이 16.6%. 탄소성분이 38.4%로 측정되었다. 대기의 높은 원소탄소함량(13 wt.%)은 석탑 흑색표면에서 검출된 원소 탄소의 기원으로 판단된다. 대기중의 토양성분 또한 석탑 흑색표면이 함유하고 있는 규산염광물의 기원으로 추정되며, 석탑표면에 축적되어 표면을 어둡게 하는 역할을 한다.

• Carbon letters
• /
• 제20권
• /
• pp.39-46
• /
• 2016

In this work, the effects of maleic anhydride (MA) content on mechanical properties of chopped carbon fibers (CFs)-reinforced MA-grafted-polypropylene (MAPP) matrix composites. A direct oxyfluorination on CF surfaces was applied to increase the interfacial strength between the CFs and MAPP matrix. The mechanical properties of the CFs/MAPP composites are likely to be different in terms of MA content. Surface characteristics were observed by scanning electron microscope, Fourier transform infrared spectroscopy, and single fiber contact angle method. The mechanical properties of the composites were also measured by a critical stress intensity factor (K_IC). From the K_IC test results, the K_IC values were increased to a maximum value of 3.4 MPa with the 0.1 % of MA in the PP, and then decreased with higher MA content.

• Journal of the Korean Wood Science and Technology
• /
• 제48권4호
• /
• pp.503-512
• /
• 2020

Using Na₂CO₃ versus NaCl as chemical activator, we compared the quality of activated carbon produced from oil palm fronds as raw material. These activators were selected for comparison because both are readily available and are environmentally friendly. In the manufacturing, we used Indonesian National Standard (SNI 06-3730-1995) parameters. For the quality comparison, we determined activated-carbon yield, moisture, ash, volatiles, and fixed-carbon contents; and adsorption capacity of iodine. The best characteristics, assessed by morphological surface analysis and Fourier transform infrared (FTIR) spectral analysis, were observed in the carbon activated by Na₂CO₃ at an activator concentration of 10% and carbonization temperature of 400 ℃. The results were as follows: activated-carbon yield, 84%; water content, 8.80%; ash content, 2.20%; volatiles content, 14.80%; fixed-carbon content, 68.60%; and adsorption capacity of iodine, 888.51 mg/g. Identification using the FTIR spectrophotometer showed the presence of the functional groups O-H, C=O, C=C, C-C, and C-H in the Na₂CO₃-activated carbon.

• 한국표면공학회지
• /
• 제37권2호
• /
• pp.80-85
• /
• 2004

Chromium-carbon (Cr-C) and chromium-carbon-phosphorus (Cr-C-P) alloy deposits using trivalent chromium sulfate baths containing potassium formate were prepared to study their current efficiency, hardness change and phase transformations behavior with heat treatment, respectively. The current efficiencies of Cr-C and Cr-C-P alloy deposits increase with increasing current density in the range of 15-35 A/dm$^2$. Carbon content of Cr-C and phosphorous of Cr-C-P layers decreases with increasing current density, whereas, the carbon content of Cr-C-P layer is almost constant with the current density. Cr-C deposit shows crystallization at $400^{\circ}C$ and has (Cr+Cr$_{ 23}$$C_{6}$) phases at $800^{\circ}C$. Cr-C-P deposit shows crystallization at $600^{\circ}C$ and has (Cr+Cr$_{23}$ $C_{6}$$+Cr_3$P) phases at $800^{\circ}C$. The hardness of Cr-C and Cr-C-P deposits after heating treatment for one hour increase up to Hv 1640 and Hv 1540 and decrease about Hv 820 and Hv 1270 with increasing annealing temperature in the range of $400～^{\circ}C$, respectively. The hardness change with annealing is due to the order of occurring of chromium crystallization, precipitation hardening effect, softening and grain growth with temperature. Less decrease of hardness of Cr-C-P deposit after annealing above $700^{\circ}C$ is related to continuous precipitation of $Cr_{23}$ $C_{6}$ and $Cr_3$P phases which retard grain growth at the temperature.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2011년도 춘계학술대회 및 Fine pattern PCB 표면 처리 기술 워크샵
• /
• pp.75-76
• /
• 2011

Hot-rolled steel plates of SPHC and SS400 were oxidized at 600, 750 and $900^{\circ}C$ for 2hr in air. With an increase in oxidation temperature, their oxidation rates increased, being accompanied with formation of pores and cracks in the thickened oxide scales that were non-adherent. The SPHC steels that were manufactured by either the arc furnace or the blast furnace displayed similar oxidation rates, indicating that their oxidation rates were insensitive to the manufacturing processes. The medium-carbon SS400 steel displayed a little faster oxidation rates than the low-carbon SS400 steel, indicating that the carbon content did not significantly influence the oxidation rates.

• Carbon letters
• /
• 제3권1호
• /
• pp.17-24
• /
• 2002

The electrochemical behavior of the $LiCoO_2$ electrode, containing carbon black as a conductor, depends upon the nature and characteristics of carbon black. In this study, six different kinds of carbon blacks were employed to investigate the relationship between the properties of carbon blacks and electrochemical characteristics of the electrode. The larger amount of surface oxygen functional groups brought the lower electrical conductivity for the carbon blacks. The electrical conductivity of carbon blacks was closely related to the impurities such as ash and volatile content. The rate capability and cyclability of the electrode were improved with the higher conductivity of carbon blacks used. So, it can be concluded that high conductive carbon black plays an important role as a conductor for high rate of charge-discharge capability and initial efficiency.