• 한국레이저가공학회지
• /
• 제4권2호
• /
• pp.13-19
• /
• 2001

When a high-power laser beam is irradiated on the surface of material, it is well known that a cavity, called a keyhole induced by the pressure action of the vapor plume, is generated in the molten material. This paper describes the interaction between a pulsed CO$_2$ laser beam and water. The laser-beam is used to generate and maintain a conical depression in the water surface similar to the keyhole created during laser penetration welding. Experimental results show that the depth of laser-beam penetration is limited by hydrodynamic instability. The instability of the surface cavity can be understood by the capillary instability of a hollow jet. Theoretical computation of the steady keyhole shape has been performed. modifying the model suggested by Andrews et al. (1976). The model predicts the qualitative behavior of the keyhole but significantly underestimates the average diameter.

• Nuclear Engineering and Technology
• /
• 제45권3호
• /
• pp.335-346
• /
• 2013

The Critical Heat Flux (CHF) of water with dispersed alumina nanoparticles was measured for the geometry and flow conditions relevant to the In-Vessel Retention (IVR) situation which can occur during core melting sequences in certain advanced Light Water Reactors (LWRs). CHF measurements were conducted in a flow boiling loop featuring a test section designed to be thermal-hydraulically similar to the vessel/insulation gap in the Westinghouse AP1000 plant. The effects of orientation angle, pressure, mass flux, fluid type, boiling time, surface material, and surface state were investigated. Results for water-based nanofluids with alumina nanoparticles (0.001% by volume) on stainless steel surface indicate an average 70% CHF enhancement with a range of 17% to 108% depending on the specific flow conditions expected for IVR. Experiments also indicate that only about thirty minutes of boiling time (which drives nanoparticle deposition) are needed to obtain substantial CHF enhancement with nanofluids.

• 한국자동차공학회논문집
• /
• 제22권5호
• /
• pp.20-28
• /
• 2014

The high velocity oxygen fuel spraying (HVOF) is a kind of surface modification process technology to form the sprayed coating layer after spraying the powder to molten or semi-molten state by the ultra-high speed at the high-temperature heat source and conflicting with a substrate. It is desirable to melt completely the thermal spray powder in order to produce the coating layer with an optimal adhesion, however, because a semi-molten powder in a spray process has the low efficiency and become a factor that degrades the mechanical property by the inducement of pore-forming within the coating layer. To improve the wear resistance, corrosion resistance and heat resistance, in this study, the plungers of high-speed and ultra-high pressure reciprocating hydraulic pumps for oil and water used in ironwork are produced with $420J_2$ and the coating layers of plungers are formed by the powders of WC-Co-Cr and WC-Cr-Ni including the high hardness WC. The surface of these plungers is modified by the super-mirror face grinding machine using variable air pressure developed in this laboratory, and then the characteristics of cross-sectional microstructure, and surface roughness and hardness values between no operation and 100 days-operation are examined and made a comparison. The fine tops and bottoms on surface roughness curve of oil-hydraulic pump plunger sprayed by WC-Cr-Ni are molded more and higher than those of water-hydraulic pump sprayed by WC-Co-Cr because the plunger diameter of oil-hydraulic pump is 0.4 times smaller than that of water-hydraulic pump and the pressure of oil-hydraulic pump exerted on the plunger is operated with the 70 bars higher than that of water-hydraulic pump. As a result, it is found that the values of centerline average surface roughness and maximum height for oil-hydraulic pump plunger are bigger than those of water-hydraulic pump plunger.

• 한국의류학회지
• /
• 제39권2호
• /
• pp.271-286
• /
• 2015

This study presented functional designs for development of functional compression wear for men in their forties based on body muscles as well as designed 2D patterns using 3D standard body form data of men in their forties. Patterns with an optimal stretch rate were proposed through a comfort evaluation. Different material was used for different areas such as the sports ability strengthening areas including body parts that often move for sports (such as the shoulders, abdomen and lower arm), areas that require ventilation for perspiration (such as the chest and back center, and armpits), and stable form areas (such as the chest, waist and elbows). The front and back surface areas of the developed pattern was an average 102.4% size compared to the body surface area. The results indicated that the 90% reduction pattern showed changes in pressure value according to area of movement, had the best breathability when worn, and had the best, most comfortable fit compared to the other subjects. The clothing pressure values of the pattern were around 22.1-23.4mmHg for the arm area (which has a big movement range and has many muscles) and 10.4-11.8mmHg for chest and abdomen areas related to major organs and breathing, indicating appropriate clothing pressure. A compression wear top pattern with pressure appropriate to the target age range and excellent appropriateness for the body form will be developed for men in their forties. A study method will be proposed to develop design technology for ergonomic compression wear tops with excellent fit and comfort.

• Current Optics and Photonics
• /
• 제8권2호
• /
• pp.138-150
• /
• 2024

This study is essential for advancing our knowledge about the interaction between long-range high-power lasers and energetic materials, with a particular emphasis on understanding the response of a 155-mm shell under various surface irradiations, taking into account external factors such as atmospheric disturbances. The analysis addresses known limitations in understanding the use of non-realistic targets and the negligence of ambient conditions. The model employs the three-dimensional level-set method, computer-aided design (CAD)-based target design, and a message-passing interface (MPI) parallelization scheme that enables rapid calculations of the complex chemical reactions of the irradiated high explosives. Important outcomes from interaction modeling include the accurate prediction of the initiation time of ignition, transient pressure, and temperature responses with the location of the initial hot spot within the shell, and the relative magnitude of noise with and without the presence of physical ambient disturbances. The initiation time of combustion was increased by approximately a factor of two with atmospheric disturbance considered, while slower heating of the target resulted in an average temperature rise of approximately 650 K and average pressure increase of approximately 1 GPa compared to the no ambient disturbance condition. The results provide an understanding of the interaction between the high-power laser and energetic target at a long distance in an atmospheric condition.

• 한국기계가공학회지
• /
• 제15권2호
• /
• pp.72-77
• /
• 2016

Airplane reservoirs made of Al7075 are coated with an anodizing layer to maintain precision, air tightness and corrosion resistance. It is commonly required that the inner surface roughness of the reservoir be less than an average $0.2{\mu}m$ to maintain stable oil pressure. Even though precision polishing is necessary to achieve this quality it is not easy. Inner surface roughness is not uniform and the quality of the product is irregular because most of the work is done by hand. The purpose of this study is to design an exclusive polishing machine and to determine the standard cutting condition and polishing condition necessary for good inner surface roughness and to improve workefficiency.

• Transactions on Electrical and Electronic Materials
• /
• 제6권6호
• /
• pp.245-248
• /
• 2005

The physical and electrical properties of polycrystalline $\beta$-SiC were studied according to different nitrogen doping concentration. Nitrogen-doped SiC films were deposited by LPCVD(1ow pressure chemical vapor deposition) at $900^{\circ}C$ and 2 torr using $100\%\;H_2SiCl_2$ (35 sccm) and $5 \%\;C_2H_2$ in $H_2$(180 sccm) as the Si and C precursors, and $1\%\;NH_3$ in $H_2$(20-100 sccm) as the dopant source gas. The resistivity of SiC films decreased from $1.466{\Omega}{\cdot}cm$ with $NH_3$ of 20 sccm to $0.0358{\Omega}{\cdot}cm$ with 100 sccm. The surface roughness and crystalline structure of $\beta$-SiC did not depend upon the dopant concentration. The average surface roughness for each sample 19-21 nm and the average surface grain size is 165 nm. The peaks of SiC(111), SiC(220), SiC(311) and SiC(222) appeared in polycrystalline $\beta$-SiC films deposited on $Si/SiO_2$ substrate in XRD(X-ray diffraction) analysis. Resistance of nitrogen-doped SiC films decreased with increasing temperature. The variation of resistance ratio is much bigger in low doping, but the linearity of temperature dependent resistance variation is better in high doping. In case of SiC films deposited with 20 sccm and 100 sccm of $1\%\;NH_3$, the average of TCR(temperature coefficient of resistance) is -3456.1 ppm/$^{\circ}C$ and -1171.5 ppm/$^{\circ}C$, respectively.

• 대한기계학회논문집B
• /
• 제26권11호
• /
• pp.1542-1551
• /
• 2002

The present study investigates the convective heat/mass transfer characteristics and pressure drop inside the rib-roughened cooling passage of gas turbine blades. The internal cooling passage is simulated using a square duct with h- and V-shaped rectangular ribs which have a 60。attack angle. A naphthalene sublimation technique is employed to determine the detailed local heat/mass transfer coefficients using the heat and mass transfer analogy. The ribs disturb the main flow resulting in the recirculation and secondary flows near the ribbed wail. The secondary flow patterns and the local heat transfer in the duct are changed significantly according to the rib orientation. A square duct with ∧ - and V-shaped ribs have two pairs of secondary flow due to the rib arrangement. Therefore, the average heat/mass transfer coefficients and pressure drop of ∧ - and V-shaped ribs are higher than those of the continuous ribs with 90$^{\circ}$ and 60$^{\circ}$attack angles. The ∧-shaped ribs have higher heat/mass transfer coefficients than the V-shaped ribs, and the uniformity of heat/mass transfer coefficient are increased with the discrete ribs due to the flow leakage and acceleration near the surface.

• 한국표면공학회지
• /
• 제30권6호
• /
• pp.406-411
• /
• 1997

Transparent conductive thin films have found many applications in active and passive electronic and opto-electronic devices such as flat panel display electrode, solar cell electrode and window heat mirror, etc. Low resistivity and high transmittance of these films can beotained by controlling deposition parameters which are oxygen partial pressure, substrate temperature and dopant concentration. In this study, non-stoichiometric and Sb-doped thin electrical properties of undoped films have been degraded with increase of substrate temperature and optical properties have been improved in Sb-doped films. The resistivity of $2.5\times10^{-3}\Omega\textrm{cm}$,/TEX>, average transmittance of 80% and sheet resistance of 130$\Omega$/$\square$ at thickess of 2000 $\AA$ could be obrained at optmal condimal conditions which were at $400^{\circ}C$ of substrate temperature, 58% of oxygen partial pressure and 5% of Sb doping concentration.

• 설비공학논문집
• /
• 제15권10호
• /
• pp.809-820
• /
• 2003

The present study investigates effects of flow velocity on the convective heat/mass transfer characteristics in wavy ducts of a primary surface heat exchanger application. Local heat/mass transfer coefficients on the wavy duct sidewall are determined by using a naphthalene sublimation technique. The flow visualization technique is used to understand the overall flow structures inside the duct. The aspect ratio and corrugation angle of the wavy duct is fixed at 7.3 and 145$^{\circ}$ respectively, and the Reynolds numbers, based on the duct hydraulic diameter, vary from 100 to 5,000. The results show that there exist complex secondary flows and transfer processes resulting in non-uniform distributions of the heat/mass transfer coefficients on the duct side walls. At low Re (Re<1000), relatively high heat/mass transfer regions like cell shape appear on both pressure and suction side wall due to the secondary vortex flows called Taylor-Gortler vortices perpendicular to the main flow direction. However, at high Re (Re>1000), these secondary flow cells disappear and boundary layer type flow characteristics are observed on pressure side wall and high heat/mass transfer region by the flow reattachment appears on the suction side wall. The average heat/mass transfer coefficients are higher than those of the smooth circular duct due to the secondary flows inside wavy duct. And also friction factors are about two times greater than those of the smooth circular duct.