• 한국안전학회지
• /
• 제29권4호
• /
• pp.78-84
• /
• 2014

Viscosity agents were added to water to improve extinguishing performance of low pressure water mist suppression system on wood cribs fire, and a small scale wood cribs fire experiment was conducted to measure the extinguishing performance. CMC and agar were used for viscosity agent and as the amount of viscosity agent enlarges, it showed the increase of the viscosity of aqueous solution and the decrease of the fluidity. On wood cribs fire experiment, the extinguishing efficiency was improved with supplemental viscosity agent as it enhanced the adhesive time of aqueous solution on the wood, and therefore expanded the contact time of fire surface. The surface tension of aqueous solution was decreased with the addition of agar which to be assumed as an increase factor of extinguishing efficiency. By the extinguishing experimental result, the most effective extinguishing agent was CMC 0.6 wt.%, with the flame suppression time and the extinguishing time were reduced by 70s and 93s respectively at this concentration.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1997년도 제26회 추계학술대회
• /
• pp.86-92
• /
• 1997

When Lubricants is used under severe running condition, tribological characteristics is very important. I have studied the lubricating oil viscosity, kinds of additives and lubricating oil temperatures were changed. In order to study the effect of oil temperature on the wear of the surface, the temperature of the oil was changed for the same sample. Moreover, the temperatures of three kinds of oils which have very different viscosities at room temperature, were varied while the oil viscosity was unchanged. It was shown from the test results that wear is not greatly affected by the amount of ZnDTP antiwear agent, but E-P additives are less effective against wear than ZnDTP additives. The viscosity of lubricating oil and its tempea-ature greatly affect the wear of the surface. Combining all the wear data with those of the surface strength, it was observed that the higher the load, the lower the scratch of wear, and also in the case of the same running load, the lower the wear, the longer the life of the surface strength.

• 한국도로학회논문집
• /
• 제16권2호
• /
• pp.35-41
• /
• 2014

PURPOSES : Surface treatment is a favorable method in the pavement preventive maintenance. This study (Part I) aimed to develop the low viscosity filling material for waterproof characteristics and high penetrable and weather resistance, and a series of companion study (Part II) presents the coating characteristics and performance analysis using field and lab tests. METHODS : Hydrophobic characteristics of the advanced surface treatment material are observed and measured the filling depth and the permeability for sand and asphalt pavement specimen using the water absorption test and permeability test, X-RAY CT test. Color difference for the weather resistance using ultraviolet ray accelerated weathering test is compared with asphalt pavement specimens. RESULTS : The developed material shows the decreased water absorption and increased impermeable effect because of the hydrophobic characteristics. It is found that the filling depth is about 6mm and weather resistance is better than asphalt pavement specimen. CONCLUSIONS : The advanced hydrophobic - low viscosity filling treatment material is developed in this study (Part I) to improve the waterproof characteristics and high filling capacity and weather resistance for the pavement preventive maintenance.

• 한국결정성장학회지
• /
• 제15권5호
• /
• pp.202-207
• /
• 2005

Kaolin과 규석 및 $Mg(OH)_2$등의 원료로 만들어진 slip을 casting 할 때 slip의 점도가 slip casting 속도와 소결체의 미세조직에 미치는 영향을 보면 slip-casting속도는 slip의 점도가 낮을 경우 감소하였으며 slip의 점도범위는 $3.0\~17.0\;cP$가 적당하였다. Slip의 점도를 조절하면 표면층, 표면 내부층, 중간층, 내면층의 미세조직을 비교적 균일하게 casting 할 수 있다 소성온도 $1350^{\circ}C$에서 시편의 구성광물은 cordierite 결정만으로 되어있었다.

• 한국해양학회지
• /
• 제29권2호
• /
• pp.119-131
• /
• 1994

모드분리기법의 gird-box형 3차원 수치모형을 이용하여 등밀도 등수심 유한영역에 서의 연직과점성 개수에 따른 취송유와 조류의 수평 유속 연직구조를 분석하였다. 연) 직과점성 계수가 수심에 일정할 경우 선영적으로 감소또는 증가하는 경우 이차함수 및 지수함수적으로 변하는 경우에 대한 해석해와의 비교를 통하여 모형 검증 및 연직유속 구조 분석이 실시되었다. 아울러 취송유에 경우 유속의 연직구조에 대한 해수표면 근 처에 "wall layer" 영향을 수치적으로 검토하였다. 모든 수직계산에서 연직층수는 열 세개로 가변 객자가 사용되었다. 수치모형은 유속의 연직구조를 만족스럽게 재연하게 으나 연직과점성 개수가 수심에 대하여 2차함수 및 지수적으로 감소하는 경우 해저면 부근에서 유속의 연직변화가 크게 나타나면서 해석해와 수치모형 결과간에 약간에 차 이가 나타났다. 수평 유속의 연직구조는 연직과점성 계수의 절대값 및 함수형태에 따 라 달라지며 해저면과 해수표면 부근의 유속은 wall layer 내의 연직과점성 계수에 민 감하게 반응하였다. 취송유에 경우에 해수표면에서의 연직 과점성 계수가 작을수록 강 한 shear가 표층에 형성되었으며 조류에 경우 연직 과점성 계수의 분포와 상관없이 해 저 한계층 상부의 유속은 거의 일정하게 나타나고 해조표내의 유속은 연직과점성 계수 가 줄어들수록 강한 shear 보였다.shear 보였다.

• 대한기계학회논문집
• /
• 제16권1호
• /
• pp.132-141
• /
• 1992

본 연구에서는 실제적으로 베나트 대류의 발생시 유체층의 상하면은 적당한 대류 열전달 계수를 가지고 있게 되는데, 이와 같은 경계 조건을 가진 가변 점성 유 체의 안정성은 연구된 바가 없다. 이에 따라 본 연구를 수행하게 되었으며 유체의 점성이 지수 함수적으로 (.nu.=.nu.o exp(-CT)) 변화할 경우를 관찰하였다. Fig.1은 대 상이 된 유체층을 보인 것으로 하부는 고정되어 있고 상부는 고정되어 있거나 자유 표 면 상태이다. 유체층의 하부는 상부보다 더 뜨겁게 되어 있는데, 이것은 유체층의 상부는 차가운 주위로 열을 빼앗기며 하부는 뜨거운 주위로부터 가열되기 때문이다. 이때 상하부의 냉각 및 가열 경계 조건은 대류경계 조건으로 주어진다. 열팽창 계수 는 양이며 온도의 증가에 따라 점성은 감소한다.이와 같은 온도-점성 관계, 수력학 적 경계조건, 열적 조건등은 프란틀 수가 큰 유체에서 표본적으로 나타나는 것들로서 선형적 안정 이론을 적용하여 옳은 결과를 얻을 수 있다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집B
• /
• pp.734-739
• /
• 2000

Vortices terminating at free surface have been investigated extensively. Most of investigations, however, are focused on surface parallel vortices and little has been known about surface normal vortex or columnar vortex. Visualized experimental results utilizing LIF technique are discussed for the purpose of characterization of columnar vortex interacting with a clean and a contaminated free surfaces in the present investigation. The results reveal that surface tension changes due to surface contamination although bulk viscosity remains constant and eventually the behavior of a columnar vortex interacting with a contaminated free surface is totally different from the clean free surface case.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집E
• /
• pp.241-246
• /
• 2001

Vortices terminating at free surface have been investigated extensively. Most of investigations, however, are focused on surface parallel vortices and little has been known about surface normal vortex or columnar vortex. Visualized experimental results utilizing LIF technique are discussed for the purpose of characterization of columnar vortex interacting with a clean and a contaminated free surfaces and a solid body interface in the present investigation. The results reveal that surface tension changes due to surface contamination although bulk viscosity remains constant and eventually the behavior of a columnar vortex interacting with a contaminated free surface and a solid body interface are totally different from the clean free surface case.

• 한국분무공학회지
• /
• 제6권2호
• /
• pp.29-36
• /
• 2001

Vortices terminating at free surface have been investigated extensively. however. are focused on surface parallel vortices and little has been known about surface normal vortex or columnar vortex. Visualized experimental results utilizing LlF technique are discussed for the purpose of characterization of columnar vortex interacting with a clean and a contaminated free surfaces and a solid body interface in the present investigation. The results reveal that surface tension changes due to surface contamination although bulk viscosity remains constant and eventually the behavior of a columnar vortex interacting with a contaminated free surface and a solid body interface are totally different from the clean free surface case.

• 펄프종이기술
• /
• 제43권5호
• /
• pp.49-54
• /
• 2011

Curtain coating has been considered as the best coating technology because it is a coating technology that forms contour coating layer with better coverage. To increase the curtain stability surfactants are being used. In this study, the effect of a surfactant on the stability of curtain coating colors was examined by evaluating dynamic surface tension with a bubble surface tensiometer. Di-2-ethylhexyl sodium sulfosuccinate was used as a surfactant since it showed low dynamic surface tension at low surface age. And we evaluated the influence of surfactant on coating color properties including surface tension, viscosity and curtain stability. The surface tension of coating color was decreased when surfactant addition was increased up to 0.5 pph, but it was leveled off at 0.3 pph of surfactant addition. With the increase of surfactant addition rate, viscosity of coating color were increased. Micelles formed by surfactant contributed to the increase of the viscosity. Curtain stability was improved with the addition of surfactant until it reached up to 0.5 pph. Excessive addition of surfactant (> 0.5 pph) didn't improve curtain stability. This was attributed to Marangoni effect(self-healing) and decreasing of curtain thickness.