• Geomechanics and Engineering
• /
• v.22 no.4
• /
• pp.319-328
• /
• 2020

This paper investigates the effect of the width of failure and tension crack (TC) on the stability of cohesive-frictional soil slopes in three dimensions. Working analytically, the slip surface and the tension crack are considered to have spheroid and cylindrical shape respectively, although the case of tension crack having planar, vertical surface is also discussed; the latter was found to return higher safety factor values. Because at the initiation of a purely rotational slide along a spheroid surface no shear forces develop inside the failure mass, the rigid body concept is conveniently used; in this respect, the validity of the rigid body concept is discussed, whilst it is supported by comparison examples. Stability tables are given for fully drained and fully saturated slopes without TC, with non-filled TC as well as with fully-filled TC. Among the main findings is that, the width of failure corresponding to the minimum safety factor value is not always infinite, but it is affected by the triggering factor for failure (e.g., water acting as pore pressures and/or as hydrostatic force in the TC). More specifically, it was found that, when a slope is near its limit equilibrium and under the influence of a triggering factor, the minimum safety factor value corresponds to a near spherical failure mechanism, even if the triggering factor (e.g., pore-water pressures) acts uniformly along the third dimension. Moreover, it was found that, the effect of tension crack is much greater when the stability of slopes is studied in three dimensions; indeed, safety factor values comparable to the 2D case are obtained.

• Journal of Industrial Technology
• /
• v.42 no.1
• /
• pp.1-5
• /
• 2022

Although the mileage of electric vehicles can be increased based on the excellent energy density of the LiNi_0.9Co_0.05Mn_0.05O₂, it is known that the reason for limiting its use is the low lifespan and poor surface stability due to the structural deformation of the LiNi_0.9Co_0.05Mn_0.05O₂. To improve the structural stability of LiNi_0.9Co_0.05Mn_0.05O₂, electrochemical performance is improved by La coating on the surface. La-modified LiNi_0.9Co_0.05Mn_0.05O₂ shows an initial capacity of 210.6 mAh/g, a capacity retention rate of 89.9 % after 50 cycles, and a retention rate of 52.5% at 6.0 C. These are superior performances than the pristine sample, because the structural stability of the LiNi_0.9Co_0.05Mn_0.05O₂ cathode is improved by the La coating.

• The Korean Journal of Physiology
• /
• v.4 no.2
• /
• pp.53-60
• /
• 1970

In an attempt to clarity the effect of X-irradiation on the activity of surfactant in rabbits, and also to observe the possible difference when the irradiation was made in single or fractionated dose, X-ray in dose of 900 r was irradiated to rabbits either in single or fractionated dose of 300 r each day for three day, Tension-area diagram of lung extract was recorded automatically by a modified Langmuir-Wilhelmy balance with a synchronized recording system designed in this department. The surface tension of lung extract was measured at 1,3,5,24, and 48 hours post-irradiation, and the results were compared with the non-irradiated normal group. The result obtained are summerized as follows: 1) The maximal surface tension, minimal surface tension, width of the tension-area diagram at the surface area of 40% in lung extract, and stability index of the normal rabbit lung extracts were 40.73 dynes/cm, 8.96 dynes/cm. 20.71 dynes/cm, and 1.28 respectively. 2) Activity of surfactant was significantly depressed by X-irradiation, and the pattern of depression was more prominent in the single irradiation group than in the fractionated group. 3) It was found that the changes of the width of the tension-area diagram at the surface area of 40% in lung extract and stability indices corresponded well with that of the maximal or minimal surface tension.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.21 no.3
• /
• pp.632-640
• /
• 1997

Changes in surface properties and detergency of sunactant mixtures were investigated in order to study the optimum mixing ratio of anionic and nonionic surfactants by measuring surface tension, interfacial tension, suspendability, and emulsification as a Amction of mixing ratio. Also, surface tension and detergency of the surfactant mixtures were determined with the increase of water-hardness or temperature. The results were as follows: the addition of NPE to anionic surfactant solutions (LAS or SDS) by 0.1 mole fraction remarkably decreased surface tension. NPE (n=15)/anionic surfactant mixtures showed a synergistic effect in lowering interfacial tension and emulsification, but NPE (n=7.5)/anionic surfactant mixtures did not. In suspension stability, however, synergism appeared when LAS or 505 was mixed with both of NPE's. With respect to the hydrophile of NPE, NPE (n=15) was more effective than NPE (n=i.5) in improving suspension stability. Detergency of LAS/NPE mixture changed almost linearly with mixing ratio, but that of SDS/NPE mixture increased remarkably by the addition of 0.1 or 0.2 mole fraction of NPE at all temperatures. As the temperature increased, surface tension of surfactant mixtures decreased and detergency was improved, but their synergistic effect decreased. In hard water, the mixtures showed better detergency than single surfactuant solutions.

• Corrosion Science and Technology
• /
• v.22 no.5
• /
• pp.368-376
• /
• 2023

Dental Ni-Ti files must ensure stability and resistance to fatigue fracture. DLC and ta-C were coated to remove defects on the surface and ensure stability, and the surface characteristics were investigated. When coated with DLC, it was black, and in case of ta-C coating, it was blue-black. Scratches, which are defects caused by mechanical processing, were formed on the surface of the un-coated Ni-Ti file from the end of the file along the direction of processing, with the Pro-file appearing in the vertical direction and the K-file appearing in the file direction. Scratches were reduced on the coated surface, and the surface roughness was greatly reduced after coating compared to before coating. The un-coated Ni-Ti file had the lowest hardness, the DLC-coated file had the highest hardness, and ta-C showed relatively high hardness. The elastic modulus of the DLC coating film was high, and the ta-C elastic modulus was low. The adhesion of the DLC coating film tended to be higher than that of ta-C, and the wear loss amount of DLC coating of taC was lower. The corrosion potential of the ta-C coating increased significantly, and the corrosion current density decreased.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.44 no.5
• /
• pp.39-45
• /
• 2012

For a fundamental study for high concentration pigment coating, the effects of alkali swellable emulsion (ASE) type rheology modifier and surface adsorption emulsion (SAE) type rheology modifier on both the stability and the viscoelastic behavior of a coating color were elucidated. The coating color prepared with SAE type rheology modifier showed superior thermal and mechanical stability than that with ASE type. In the high concentration and high speed coating process, the mechanical stability of a coating color was a key parameter since both impact force and shear force were increased with the increase of coating color concentration and coating speed, respectively.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.6 s.249
• /
• pp.615-621
• /
• 2006

Increased application of optical disks requires more improved dynamic stability of rotating disks. In this study, a new concept of controlling the processing conditions of injection molded disks was developed to improve vibration characteristics. The critical speed, which shows stiffness and dynamic stability of disk, is affected by the residual stress distribution; this varies as functions of distance from the gate and processing condition. The critical speed of disk was calculated with the initial stress taken into consideration, which was determined from injection molding simulation. Choosing melt temperature, mold temperature, filling speed and packing pressure as design parameters, critical speed is maximized with the method of response surface. It is shown that the stability of injection molded disk has been improved for the new condition obtained as a result of the study proposed.

• Journal of the Korean Ceramic Society
• /
• v.27 no.2
• /
• pp.226-232
• /
• 1990

The degradation phenomena and thermal stability of 2.5Y-TZP at low-temperature were studied by means of XRD, Raman spectra and microstructural analysis. The degradation of heat-treated 2.5Y-TZP at 20$0^{\circ}C$-20hr in air was observed on the TZP surface, be caused by the cracks generated from tlongrightarrowm transformation, and the cracks was propagated inside the polycrystalline body. The ZrO2 grain boundaries and grains near the crack were revealed as if these were diffused and dissolved. And it was also observed mlongrightarrowt transformation as the degraded TZP was refired at 140$0^{\circ}C$, and it was thought to be the fact that the moisture in atmosphere during the aging process contributed to the degradation. The thermal stability of 2.5Y-TZP was improved dramatically with an addition of 3w/o CeO2 or a provision of high Y2O3 concentration on the TZP surface.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.215-215
• /
• 2011

The bonding configuration and adsorption stability of alanine and leucine adsorbed on Ge(100)-2${\times}$1 surface were investigated and compared using core-level photoemission spectroscopy (CLPES) and density functional theory (DFT) calculations. The bonding configuration, stability, and adsorption energies were evaluated for two different coverage levels. In both cases, the C 1s, N 1s, and O 1s core-level spectra at a low coverage (0.30 ML) indicated that the carboxyl and amine groups participated in bonding with the Ge(100) surface in an "O-H dissociated-N dative bonded structure". At high coverage levels (0.60 ML), both this structure and an "O-H dissociation bonded structure" were present. As a result, we found that alanine adsorbs more easily (lower adsorption energy) than leucine on Ge(100) surfaces due to less steric hindrance of side chain.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2014.11a
• /
• pp.214-214
• /
• 2014

Computational analysis of aqueous solution stability of Fe-Cr-Ni system to find an electroplating condition of Fe-Cr-Ni layer. Aqueous sulfate solution with iron, chromium and nickel ions was selected by using a numerical S/W with which aqueous solution stability was analyzed. Several possible conditions to perform electro-forming of Fe-Cr-Ni were selected with thermo-dynamical data. The Fe-Cr-Ni system was electro-formed which composition and microstructure of the electroplated Fe-Cr-Ni significantly depended on the solution temperature and electro-potential. The final composition of Fe-3%Cr-48%Ni with less than $30{\mu}m$ thick was well electroplated.