• The Research Journal of the Costume Culture
• /
• v.16 no.1
• /
• pp.158-165
• /
• 2008

The purpose of this study was to investigate the dyeing property and ultraviolet-cut ability on silk 100% and nylon 100% fabrics dyed with Rhus verniciflua extracts. This study was investigated K/S values, surface color, washing fastness, dry cleaning fastness and ultraviolet-cut ability of the silk and nylon fabrics dyed with Rhus verniciflua extracts under the various dyeing conditions. As mordanting were used Tin(II) Chloride dihydrate $(SnCl_2{\cdot}2H_2O)$, Copper(II) sulfate pentahydrate$(CuSO_5{\cdot}5H_2O)$, Iron(II)Chloride$(FeC_2{\cdot}4H_2O)$. pH was adjusted by sodium carbonate$(Na_2CO_3)$ and formic acid(HCOOH). The optimum dyeing temperature, dyeing time, and pH of the silk fabrics dyed with Rhus verniciflua extracts were $90^{\circ}C$, 100min, and in the nylon fabrics were $90^{\circ}C$, 45min. It were colored(munsell value) 6.4Y 7.5/4.1 in the silk fabrics and colored 4.3Y 6.6/5.9 in the nylon fabrics dyed with Rhus verniciflua extracts. Washing fastness and dry-cleaning fastness in the silk and nylon fabrics dyed with mordanting agent improved in $4{\sim}5$ grade. UV-A test showed that nylon fabrics a high rate of 92% with Rhus verniciflua extracts.

• Journal of Industrial Technology
• /
• v.24 no.B
• /
• pp.107-116
• /
• 2004

This thesis is results of experimental works on the behavior of the cut-and-cover tunnel. Centrifuge model tests were performed to simulate the behavior of the cut-and-cover tunnels having cross sections of national road and subway tunnels. Model experiments were carried out with changing the cut slope and the slope of filling ground surface. Displacements of tunnel lining resulted from artificially accelerated gravitational force up to 40g of covered material used in model tests, were measured during centrifuge model tests. In model tests, Jumunjin Standard Sand with the relative density of 80 % and the zinc plates were used for the covered material and the flexible tunnel lining, respectively. Basic soil property tests were performed to obtain it's the property of Jumumjin Standard Sand. Shear strength parameters of Jumunjin Standard Sand were obtained by performing the triaxial compression tests. Direct shear tests were also carried out to find the mechanical properties of the interface between the lining and the covered material. Compared results model tests estimation with respect to displacements of the lining.

• Korean Journal of Crystallography
• /
• v.12 no.2
• /
• pp.102-112
• /
• 2001

The mechanical properties of silicon crystals are important from the viewpoint of wafer and device fabrication processes. It is now widely recognized that silicon undergoes a series of phase transformations when subjected to high pressures, using conventional high pressure devices, such as diamond anvils or indenters. Diamond tip scratching on a silicon surface in the various conditions introduces various kinds of mechanical damage and stressed states. Micro Raman spectroscopy was used to observe the phase transition of single crystal silicon. As results, different morphologies were observed as functions of scratching speed and loading condition and various phases were observed as functions of scratching speed and loading condition.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.433-436
• /
• 2008

Deterioration in the concrete structure are due to carbonation, chloride ion attack and frost attack. Therefore, concrete structure is needed to surface protection for increase durability using silicate impregnants. Thus, this study is concerned with self-cleaning and durability of silicate hydrophilic impregnants of concrete structure using lithium and potassium silicates. From the experimental test results, lithium and potassium silicates have a good properties as a carbonation resistance. Lithium and potassium silicates make good use of hydrophilic impregnants of concrete structures.

• Journal of the Korea Institute of Building Construction
• /
• v.6 no.1 s.19
• /
• pp.73-77
• /
• 2006

Drying Shrinkage has much complexity as it has relations with both internal elements of concrete and external factors. Therefore, experiments on Concrete Drying Shrinkage are carried out in this study under simplified circumstances applying temperature & Humidity test chamber which enables constant temperature and humidify. Comparative analyses have been made respectively according to the consequences aiming at modelling for prediction of Concrete Drying Shrinkage and making out measures to reduce it. As a result Strain Rate of Drying Shrinkage of concrete was measured to increase by average $10{\times}10^{-5}$ in proportion to additional 4% increase in fine aggregate ratio, when water/cement ratio constant. Strain Rate of Drying Shrinkage in pit sand concrete increased 20% higher than measured when in river sand under the condition of 90-day material age. 6. Strain Rate of Drying Shrinkage in sea sand concrete increased $10%{\sim}15%$ higher than measured when in river sand. The results of prediction of Rate of Drying Shrinkage by Response Surface Analysis are as fellows. The coefficient of correlation of Drying Shrinkage in concrete was over 90%.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.26-26
• /
• 2010

Cadmium sulfide (CdS) thin film for flexible optical device applications were prepared at $H_2(Ar+H_2)$ flow ratios on polyethersulfon(PES) flexible polymer substrates at room temperature by radio frequency magnetron sputtering technique. The CdS thin films deposited at room temperature showed a (002) preferred orientation and the smooth surface morphologies. Films deposited at a hydrogen flow ratio of 25% exhibited a photo- and dark-sheet resistance of about 50 and $2.7{\times}10^5{\Omega}$/square, respectively. From the result of the bending test, CdS films exhibit a strong adhesion with the PES polymer substrates and the $Al_2O_3$ passivation layer deposited on the CdS films only shows an increase of the resistance of 8.4% after exposure for 120 h in air atmosphere.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.443-443
• /
• 2008

본 연구에서는 Ga-doped ZnO(GZO)-Ag-GZO 다층 투명전극을 Dual DC magnetron sputtering system을 이용 하여 유리기판 위에 상온에서 제작하여 Ag 두께에 따른 전기적, 광학적, 구조적 특성변화를 조사하였다. Hall effect measurement와 UV/Vis spectrometer로 전기적, 광학적 특성을 분석하였으며, X-ray diffraction(XRD)와FE-SEM분석을 통해 결정성과 표면 특성을 조사하였다. FE-SEM 분석결과 island 형태에서 continuous layer로 박막의 형상이 바뀌면서 다층 투명전극의 전기적, 광학적 특성에 영향을 미치는 것을 알 수 있었다. 본 실험에서 Ag 두께 12 nm에서 가장 최적화되어 유리기판위에 상온에서 증착되었음에도 불구하고 $5.5{\times}{\times}10^{-5}\Omega$-cm, $6\Omega$/sq. 의 매우 낮은 면저항과 비저항을 각각 나타내었고 550 nm 파장에서 87 % 의 높은 광 투과도를 나타내었다. 또한 두께 12 nm의 Ag가 삽입된 다층 투명전극을 polyethylene terephthalate (PET) 기판위에 성막하여 Bending test를 실시하여 0.1% 이하의 매우 낮은 저항변화를 확인함으로써 플렉시블 기반의 디스플레이나 태양전지의 투명 전극으로서의 응용 가능성을 확인하였고 마지막으로 최적화된 다층 투명전극을 유기물태양전지의 애노드에 적용하여 기존 ITO 애노드를 대체할 수 있는 투명전극으로서의 가능성을 제시하였다.

• Journal of the Microelectronics and Packaging Society
• /
• v.11 no.1
• /
• pp.43-47
• /
• 2004

We have been using Moisture Barrier Bags for dry packing of semiconductor packages to prevent moisture from absorbing during shipping. Moisture barrier bag material is required to be waterproof, vapor proof and offer superior ESD (Electro-static discharge) and EMI shielding. Also, the bag should be formed easily to the shape of products for vacuum packing while providing excellent puncture resistance and offer very low gas ＆ moisture permeation. There are some problems like pinholes and punctured bags after sealing and before the surface mount process. This failure may easily result in package pop corn crack during board mounting. The bags should be developed to meet the requirements of excellent electrical and physical properties by means of optimization of their raw material composition and their thickness. This study investigates the performance of moisture barrier bags by characterization of their mechanical endurance, tensile strength and through thermal analysis. By this study, we arrived at a robust material composition (polyester/Aluminate) for better packing.

• Composites Research
• /
• v.12 no.6
• /
• pp.83-89
• /
• 1999

The impact strength and fracture behavior of rubber/polymer composites were investigated with respect to two factors: (i) characteristic ratio, $C_{\infty}$ as a measure of chain flexibility of the polymer matrix and (ii) the rubber particle size in polymer blend system. In this study C was controlled by the composition ratio of polyphenylene oxide (PPO) and polystyene (PS). Izod impact test and fractographic observation of the fracture surface using scanning electron microscope were conducted. Finite element analysis were carried out to gain understanding of plastic deformation mechanism (shear yielding and crazing) of these materials. Shear yielding was found to be enhanced when the flexibility of matrix polymer was relatively low and the rubber particles were small.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.9
• /
• pp.1842-1848
• /
• 2002

Although DLC coatings have good tribological properties, these are dependant on the deposition method, the property of contact surface, and test condition. Humidity, which has little influence on tribological behavior in macro scale, is an important factor of tribological behavior in small devices like MEMS. The objective of this study is to investigate the tribological behavior of DLC coatings with particular attention to their wettability at various humidities. DLC coatings were deposited on Si substrates and tested using a reciprocating friction tester against Si$_3$N$_4$balls at various humidities. The results showed that the tribological behavior of DLC coatings was dependant on relative humidity and wettablility of DLC coatings. Friction coefficient at high relative humidity was higher thar that at low relative humidity. The tungsten-containing DLC coatings had a good wear resistance at low relative humidity whereas DLC coatings derived from argon(Ar)+cesium(Cs) gases showed a good wear resistance at high relative humidity.