• 대기
• /
• 제26권1호
• /
• pp.127-140
• /
• 2016

In this study, the correlations between AST850 and precipitation, and those between WDT and precipitation in the Yeongdong coastal region under the direct/indirect influence of the expansion of cP (continental polar air mass) high were quantitatively analyzed based on the winter season data for the last 20 years, according to surface pressure patterns such as Type 1 (cP high expansion type), Type 2 (cP high expansion + trough type), Type 4 (South trough type), and Type 5 (East Sea trough type). Here, AST850 represents 'sea surface temperature minus temperature on 850 hPa level' and WDT represents 'a speed of 1000 hPa wind projected onto a certain wind direction times precipitation duration in hour'. First, the correlation coefficients between AST850 and precipitation in Type 1, Type 2, and Type 5 cases were 0.253, 0.384, and 0.398 respectively, indicating that a tendency of increasing precipitation linearly with the value of AST850 is slightly presented. In the case of Type 4, however, the coefficient was -0.15, representing almost no linear correlation between AST850 and precipitation. In the correlation between WDT and precipitation, there was the largest correlation coefficient (0.464) between WDT along a direction of $90^{\circ}$ and at EN1 in Type 1 cases. In the case of Type 2, there was the largest correlation coefficient (0.767) between WDT along a direction of $67.5^{\circ}$ and at ES1. In the case of Type 4, there was the largest correlation coefficient (0.559) between WDT along a direction of $22.5^{\circ}$ and at EN2. Finally, in the case of Type 5, there was the largest correlation coefficient (0.945) between WDT along a direction of $315^{\circ}$ and at SE1, representing the largest coefficient among the types. It was found that surface wind directions with the highest correlations to precipitation in the Yeongdong coastal area on winter season were varied according to surface pressure patterns, and that the correlations between WDT and precipitation were higher than those between AST850 and precipitation.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2005년도 제28회 학술발표회 초록집
• /
• pp.38-38
• /
• 2005

• 한국동물학회지
• /
• 제31권4호
• /
• pp.273-282
• /
• 1988

생쥐에 PMSG와 hOG를 주사한 후 난자-난구복합체의 미세구조의 변화를 환찰함으로세 난구세포의 분산현상을 규명하고자 본 실험을 행하였다. 난자는 PMSG 주사후 48시간까지 별 다른 변화가 없었고 다만 표면막에 miGrOVilli와 Coaled pit의 수가 감소하는 경향을 보였다. 그러나 PMSG-hCG주사 12시간 후에 배란된 난자의 표면은 microvilli와 coated pit가 사라져서 평평하게 되었다. 방사관세포는 PMSG주사 48시간 후메 밀착해 있던 투명대와 간격이 생기기 시작하였고, 투명대를 통관하여 난자의 표면막과 desmosome으로 연결되어 있던 세포질돌기도 퇴화의 징후를 보였다. PMSG-hCG주사 후에는 급속히 격리, 분산되고 세포질돌기는 퇴화하였으며 dermo-some도 사라겼다. 난구세포들은 대조군에서 밀집되어 있었고 거의 gap junction으로 연결되어 있었는데, PMSG주사 24시간 후에는 모양이 등글게 되고 더욱 밀집되었으며, 48시간 후에는 거의 loose junction으로 연결되었고 분산되기 시작하였다. 결국 PMSG-hCG주사 If시간 후에는 완전히 분산되었고 거의 모두 핵응축과 괴사현상을 보였다. 난자- 난구 복합체의 분산은 배란전에 PMSG에 의하여 시작되고 hCG에 의하여 촉진 완결된다는 것이 확실하다. The ultrastructural changes of the oocyte-cumulus complexes of mouse alter injection of PMSG and hOG have been investigated in order to elucidate expansion phenomenon of the cumulus cells. The oocytes until 48 hours after PMSC injection showed no change except a tendency of decrease in numbers of microvilli and the coated pelts on surface membrane. However, surface membrane of the ovulated oocytes 12 hours after PMSC-hCC injection changed to be smooth due to disapperance of microvilli and coated pits. Corona radiate cells tightly attaching to zona pe]lucida 48 hours after PMSC injection began to be detached and their cytoplasmic processes connected by desmosome to oocyte surface membrane showed a degeneration symptom. Thereafter the detachment and degeneration were accelerated by hCG injection and followed by disappearence of desmosome. The cumulus cells in control group were compacted and connected by almost 9aP junction each another. Ite cumulus cells 24 hours after PMSG injection were changed to be round form and more tightly compacted. However, the cumulus cells 48 hours after PMSG injection were connected by almost loose junction and showed the beginning of expansion. Eventuallv, the cumulus cells 12 hours a%or PMSG-hCG injection were completely expanded, and became pvknotic and necrotic in most It is clear that the expansion of oocyte-cumulus complex were initiated by PMSC, then accelerated and completed by hCG before ovulation.

• Archives of Plastic Surgery
• /
• 제46권1호
• /
• pp.34-38
• /
• 2019

Background Acellular dermal matrices (ADMs) have recently become widely used in breast reconstruction, but the correlation between the final expander volume and the surface area of the ADM is not well understood. In this study, the expansion of the surface area of ADM and the expander volume was studied retrospectively in cases of acellular dermis-assisted tissue expander breast reconstruction. Methods Twenty cases of immediate breast reconstruction using an ADM-assisted tissue expander from January 2015 to December 2015 were evaluated. In all 20 cases, CGCryoDerm was used as the matrix, with a thickness of 1-3 mm. No slit incisions were made. Finally, the proportional increase in the area of the fully expanded ADM was compared to that of the tissue expander volume. Results The proportional increase in the ADM surface area was calculated to be from 1.1 to 2.46, with a mean value of 1.7. Additionally, under the assumption that the expander had a spherical shape, the increase in its radius (the cube root of its volume) was assessed. The range of the proportional increase in the expander radius was 1.1 to 2.24, with a mean value of 1.66. The proportional increase in the radius of the expanded ADM surface area ranged from 1.04 to 1.34, with a mean ratio of 1.28. Conclusions The results of this study confirmed that the ADM expanded when the tissue expander was inflated. However, the ADM expanded to a lesser extent than the tissue expander, indicating that the muscle and other tissues expanded more than the ADM when the tissue expander was inflated.

• International Journal of Fluid Machinery and Systems
• /
• 제3권2호
• /
• pp.150-159
• /
• 2010

Laidback fan shaped film-cooling hole is formulated numerically and optimized with the help of three-dimensional numerical analysis, surrogate methods, and the multi-objective evolutionary algorithm. As Pareto optimal front produces a set of optimal solutions, the trends of objective functions with design variables are predicted by hybrid multi-objective evolutionary algorithm. The problem is defined by four geometric design variables, the injection angle of the hole, the lateral expansion angle of the diffuser, the forward expansion angle of the hole, and the ratio of the length to the diameter of the hole, to maximize the film-cooling effectiveness compromising with the aerodynamic loss. The objective function values are numerically evaluated through Reynolds- averaged Navier-Stokes analysis at the designs that are selected through the Latin hypercube sampling method. Using these numerical simulation results, the Response Surface Approximation model are constructed for each objective function and a hybrid multi-objective evolutionary algorithm is applied to obtain the Pareto optimal front. The clustered points from Pareto optimal front were evaluated by flow analysis. These designs give enhanced objective function values in comparison with the experimental designs.

• 한국정밀공학회지
• /
• 제14권12호
• /
• pp.153-159
• /
• 1997

A thermally-driven polysilicon microactuator has been fabricated using surface micromachining techniques. It consists of P-doped polysilicon as a structural layer and TEOS(tetraethylorthosilicate) oxide as a sacrificial layer. The polysilicon was annealed for the relaxation of residual stress which is the main cause to its deformation such as bending and buckling. And newly developed HF GPE(gas-phase etching) process was also employed to eliminate the troublesome stiction problem using anhydrous HF gas and CH$_{3}$OH vapor, and successfully fabricated the microactuators. The actuation is incurred by the thermal expansion due to the current flow in the active polysilicon cantilever, which motion is amplified by lever mechanism. The moving distance of polysilicon microactuator was experimentally conformed as large as 21 .mu. m at the input voltage level of 10V and 50Hz square wave. The actuating characteris- tics are also compared with the simulalted results considering heat transfer and thermal expansion in the polysilicon layer. This microactuator technology can be utilized for the fabrication of MEMS (microelectromechanical system) such as microrelay, which requires large displacement or contact force but relatively slow response.

• 대한가정학회지
• /
• 제18권4호
• /
• pp.31-39
• /
• 1980

The basic pattern of skirt should be functional in addition to be fit the body. The author paid special attention to the expansion and contraction of the shell which were made the lower trunk and thigh caused by sitting motions. The replicas of the shell were taken by using a gypsum method on 1 female under 4 standardized motions; standing motion, (basic motion), sitting on the chair with flextion 90' at the hip and the knee joints sitting with dropping knees, and sitting with benting legs side wards. Those replicas obtained were developed to the patterns and changes in shape and area of those were measured. Typical displacement and transformation of the shell surface patterns were showed geographycally fig 5-1 to 5-4. mean values of expansion and constriction were obtained by measuring the shell surface on 60 female under the 4 motions. the mean values of it were showed numerically in Table 1-1 to 1-3. The following results were obtained; 1. Vertical constriction of front of the shell were observed near sulcus in guinalis, and vertical extension were near the knees. Horizontal extension were observed near the thighs and the knees. 2. Vertical constrictions of the back of the shell were observed near the knees. It seemed to be influnced the flexion angles of knee points. vertical extension were near gluteus and thighs. Horizontal constriction were small, and horizonlal extension were near gluteus. 3. The high rates of constriction and extension were found near sulcus in guinalis, glutes, and knees. 4. The rates of constriction and extension on the waist line were very low. 5. The highest values of constriction and extension were found in hip and knees.

• Journal of Mechanical Science and Technology
• /
• 제19권9호
• /
• pp.1790-1800
• /
• 2005

The examination on the operating mechanism of a pulsating heat pipe (PHP) using visualization revealed that the working fluid in the PHP oscillated to the axial direction by the contraction and expansion of vapor plugs. This contraction and expansion is due to the formation and extinction of bubbles in the evaporating and condensing section, respectively. In this paper, a theoretical model of PHP was presented. The theoretical model was based on the separated flow model with two liquid slugs and three vapor plugs. The results show that the diameter, surface tension and charge ratio of working fluid have significant effects on the performance of the PHP. The following conclusions were obtained. The periodic oscillations of liquid slugs and vapor plugs were obtained under specified parameters. When the hydraulic diameter of the PHP was increased to d=3mm, the frequency of oscillation decreased. By increasing the charging ratio from 40 to 60 by volume ratio, the pressure difference between the evaporating section and condensing section increased, the amplitude of oscillation reduced, and the oscillation frequency decreased. The working fluid with higher surface tension resulted in an increase in the amplitude and frequency of oscillation. Also the average temperature of vapor plugs decreased.

• 대한기계학회논문집A
• /
• 제26권7호
• /
• pp.1340-1347
• /
• 2002

Finite element simulations are being widely used to increase the efficiency and effectiveness of design of bulk metal forming processes. In such simulations, proper consideration of friction condition is crucial in obtaining reliable results. For this purpose, tip test based on backward extrusion was proposed recently. In this lest, a cylindrical billet is positioned in a shallow groove of a counter punch for centering purpose and formation of a radial tip is induced on the extruded end of the workpiece. In this study, the effect of centering groove on tip test was investigated. The quantitative ratio of the shear friction factors between the punch and die was numerically determined depending on the shape of centering groove. Also, surface expansion and pressure distribution along the punch and die were considered in order to better understand the reason that friction condition at the punch compared to the one of die was more severe.

• 소성∙가공
• /
• 제18권4호
• /
• pp.310-316
• /
• 2009

Micro lens array(MLA) is widely used in information technology(IT) industry fields for various applications such as a projection display, an optical power regulator, a micro mass spectrometer and for medical appliances. Recently, MLA have been fabricated and developed by using a reflow method having the processes of micro etching, electroplating, micro machining and laser local heating. Laser thermal relaxation method is introduced in marking of microdots on the surface of densified glass. In this paper, we have proposed a new direct fabrication process using UV laser local thermal-expansion(UV-LLTE) and investigated the optimal processing conditions of MLA on the surface of negative photo-resist material. We have also studied the 3D shape of the micro lens obtained by UV laser irradiation and the optimal process conditions. And then, we made chrome mold by electroplating. After that, we made MLA using chrome mold by hot embossing processing. Finally, we have measured the opto-physical properties of micro lens and then have also tested the possibility of MLA applications.