• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.12 no.3
• /
• pp.99-114
• /
• 2012

Proxy Mobile IPv6 (PMIPv6) has received considerable attention between telecommunications and the Internet communities and does not require active participation of the Mobile Node (MN) by way of network-based mobility management. The PMIPv6 domain is studying establishment in progress to support extensively a number of MN by using a low handover latency. In this research, we are propose a novel 3S scheme for building Scalable and Secure and Seamless PMIPv6 domains. In the proposed scheme, all of Mobility Access Gateway (MAG) are acting as the Local Mobility Anchor (LMA) and composing a virtual ring with another MAG. General hashing is used in the efficient distribution-mapping between each MN and the MN's LMA of all MAGs. And, MAG and MN are authenticated using the symmetric key. Through mathematical analysis, we verifies the safety, scalability, and seamless service for 3S. Also, we're propose a handover procedure of 3S and show better than the existing schemes in terms of handover latency.

• Journal of Institute of Control, Robotics and Systems
• /
• v.18 no.12
• /
• pp.1079-1085
• /
• 2012

For precise motion control, S-curve velocity profile is generally used but it has disadvantage of relatively long calculation time for floating-point arithmetics. In this paper, we present a new generating method for velocity profile to reduce delay time of profile generation so that it overcomes such disadvantage and enhances the efficiency of precise motion control. In this approach, the velocity profile is designed based on the gamma correction expression that is generally used in image processing to obtain a smoother movement without any critical jerk. The proposed velocity profile is designed to support both T-curve and S-curve velocity profile. It can generate precise profile by adding an offset to the velocity profile with decimals under floating point that are not counted during gamma correction arithmetic operation. As a result, the operation time is saved and the efficiency is improved. The proposed method is compared with the existing method that generates velocity profile using ring buffer on a 8-bit low-cost MCU. The result shows that the proposed method has no delay in generating driving profile with good accuracy of each cycle velocity. The significance of the proposed method lies in reduction of the operation time without degrading the motion accuracy. Generated driving signal also shows to verify effectiveness of the proposed method.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.45 no.12
• /
• pp.139-145
• /
• 2008

In this paper, a microstrip surface wave antenna(SWA) with a frequency selective surface structure(FSS) is designed and measured. A microstrip SWA has many advantages such as low profile, low weight, easy fabrication, and compatibility with monolithic microwave integrated circuits(MMIC). In addition, it has demonstrated monopole like beam patterns. The microstrip SWA consists of two parts : a center-fed modified microstrip patch to excite surface wave, and a periodic patches to support the propagation of the surface waves. To obtain wide bandwidth, the ring type parasitic element is inserted and the circular patch is selected for the unit element in FSS structure. Experimental results show that the microstrip SWA has monopole like beam patterns at 5.9GHz. Impedance bandwidth and gain is 12% and 5.6dBi.

• Journal of KIISE:Computer Systems and Theory
• /
• v.26 no.10
• /
• pp.1206-1216
• /
• 1999

이동 호스트란 시간과 공간의 제약 없이 필요한 기능을 수행하고, 또한 원하는 정보에 접근할 수 있는 휴대용 컴퓨터를 일컫는다. 이동 컴퓨팅 환경이란 이러한 이동 호스트들을 지원할 수 있도록 구성된 분산 환경이다. 따라서 이동 컴퓨팅 환경에서의 분산 알고리즘은 정적 호스트만을 고려한 기존의 분산 환경에서와는 다르게 이동 호스트의 여러 가지 특성들을 고려하여 제안되어야 한다. 즉, 이동 컴퓨팅 환경의 도래로 인하여 이동성과 휴대성, 그리고 무선 통신과 같은 특성들을 고려한 새로운 분산 상호 배제 알고리즘이 필요하다. 이제까지 이동 컴퓨팅 환경에서의 상호 배제 알고리즘은 토큰 링 구조에 기반을 두고 설계되었다. 토큰 링 구조는 이동 호스트들의 위치를 유지하기 위하여 높은 비용을 필요로 하는 단점을 가지고 있다. 본 논문에서는 균형 높이 트리(height-balanced tree)라는 새로운 모형을 제안함으로써 정적 분산 환경과 이동 분산 환경이 혼합된 환경에서 상호 배제 비용을 감소시킬 수 있는 새로운 알고리즘을 제안하며, 각 경우에 있어서의 비용을 산출하고 평가한다.Abstract The mobile host is a potable computer that carries out necessary functions and has the ability to access desirable informations without any constraints in time and space. Mobile computing environment is a distributed environment that is organized to support such mobile hosts. In that environment, distributed algorithms of which environment not only with static hosts but with mobile host's several properties should be proposed. With the emergence of mobile computing environments, a new distributed mutual exclusion method should be required to consider properties mobile computing system such as mobility, portability, and wireless communication. Until now, distributed mutual exclusion methods for mobile computing environments are designed based on a token ring structure, which have the drawbacks of requiring high costs in order to locate mobile hosts. In this paper, we propose a distributed mutual exclusion method that can reduce such costs by structuring the entire system as a height-balanced tree for static distributed networks and for networks with mobile hosts. We evaluated the operation costs in each case.

• Journal of Korea Trade
• /
• v.25 no.5
• /
• pp.58-73
• /
• 2021

Purpose - In the context of economic globalization and the continuous development of international trade, as countries around the sea peninsula, port construction is particularly important. Based on the research on the influencing factors of port logistics development based on the allocation analysis, QCA (Qualitative Comparative Analysis) provides the basis for the planning and policy of port logistics development and has important theoretical value and practical significance for improving the level of port logistics management, reducing logistics operating costs and increasing economic benefits. In the tide of global integration for the development of port logistics, promote the growth of foreign trade economy of the city. It is also of great significance to the development and progress of commerce and trade. Design/methodology - Based on the relevant data samples of various ports in South Korea, this paper uses fsQCA (fuzzy set Qualitative Comparative Analysis) to integrate and analyze the influence mechanism of port logistics development and extracts five influencing factors of port logistics development, including the port's scale and infrastructure in the hard environment, port-neighboring enterprises in the soft environment, hinterland economy and government support. Findings - The five factors are unable to separately constitute the necessary and sufficient conditions of port logistics development, only a combined model can influence lake port logistics development. The scale and infrastructure of the port itself and port-neighboring ring enterprises are the main core conditions, which work together on the port, affect the throughput capacity of the port, and promote the development of port logistics. When the port-neighboring enterprises are not complete and the scale is low, the growth of port throughput will be restrained and the development of port logistics will be affected, whether the hinterland economic benefits are general, the development of port-neighboring enterprises is insufficient, or the government supports are limited. Originality/value - Through the research on the development of port logistics in South Korea from the perspective of configuration, this paper finds the configuration influence of hard environment and soft environment on the development of port logistics, which has important theoretical and practical significance for better promoting the development of port logistics in South Korea.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.3
• /
• pp.92-99
• /
• 2021

An automatic transmission, which consists of several decks of planetary gear sets, provides multiple speed and torque ratios by actuating brakes and clutches (mechanical friction components) for connecting central members of the planetary gear sets. The gear set consists of the sun gear, the ring gear, and the carrier supporting multiple planet gears with pin shafts. In designing a new automatic transmission, there are many steps to design and analyze: gears, brakes and clutches, shafts, and other mechanical components. Among them, selecting thrust bearings that not only allow the relative rotation of the central members and other mechanical components but also support axial forces coming from them is important; doing so yields superior driving performance and better fuel efficiency. In selecting thrust bearings, the magnitude of axial forces on them is a critical factor that affects their bearing size and performance; its results are systematically related to the direction of the helical angle of each planetary gear set (a geometric design profile). This research presents the effects of the helical angle direction on the axial forces acting on thrust bearings in an automatic transmission consisting of planetary gear sets. A model transmission was built by analyzing kinematics and power flows and by designing planetary gear sets. The results of the axial forces on thrust bearings were analyzed for all combinations of helix angle directions of the planetary gear sets.

• Archives of Plastic Surgery
• /
• v.36 no.6
• /
• pp.691-701
• /
• 2009

Purpose: Deviations of arterial palmar arches in the hand can be explained on the embryological basis. The purpose of this study was to provide new information about palmar arches through cadaver's dissection. The values of the location and diameter in these vessels were analyzed in order to support anatomical research and clinical correlation in the hand. Methods: The present report is based on an analysis of dissections of fifty - three hands carried out in the laboratory of gross anatomy. A reference line was established on the distal wrist crease to serve as the X coordinate and a perpendicular line drawn through the midpoint between middle and ring fingers, which served as the Y coordinate. The coordinates of the x and y values were measured by a digimatic caliper, and statistically analyzed with Student's t - test. Results: Complete superficial palmar archs were seen in 96.2 % of specimens. In the most common type of males, the superficial arch was formed only by the ulnar artery. In the most common type of females, the superficial arch was formed anastomosis between the radial artery and the ulnar artery. The average length of the superficial and deep palmar arch is $110.3{\pm}33.0mm$ and $67.9{\pm}14.0mm$ respectively. Regarding the superficial palmar arch, ulnar artery starts $-16.1{\pm}5.1mm$ on X - line, and $2.5{\pm}24.5mm$ on Y - line. Radial artery appears on palmar side $7.7{\pm}3.2mm$ on X - line, and $20.9{\pm}10.9mm$ on Y - line. But radial artery starts on $6.3{\pm}3.6mm$ on X - line, and $3.4{\pm}5.1mm$ on Y - line. Digital arteries of superficial palmar arch starts on $6.1{\pm}3.7mm$, $33.9{\pm}8.8mm$ on index finger, $1.8{\pm}3.4mm$, $40.1{\pm}7.3mm$ on middle finger, $-3.2{\pm}4.9mm$, $42.6{\pm}7.0mm$ on ring finger, and $-8.9{\pm}5.1mm$, $42.5{\pm}80mm$ on little finger in respective X and Y coordinates. Radial artery of deep palmar arches measured at the palmar side perforating from the dorsum of hand. It's coordinates were $9.7{\pm}4.8mm$ on X - line, $21.7{\pm}10.2mm$ on Y - line. Ulnar artery was measured at hypothenar area, and it's coordinates were $-20.4{\pm}6.3mm$ on X - line, and $30.6{\pm}7.4mm$ on Y - line. Conclusions: Anatomically superficial palmar arch can be divided into a complete and an incomplete type. Each of them can be subdivided into 4 types. The deep palmar arch is less variable than the superficial palmar arch. We believe these values of the study will be used for the vascular surgery of the hand using the endoscope and robot in the future.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.2
• /
• pp.131-143
• /
• 2013

Vibration condition monitoring of low-speed rotational slewing bearings is essential ever since it became necessary for a proper maintenance schedule that replaces the slewing bearings installed in massive machinery in the steel industry, among other applications. So far, acoustic emission(AE) is still the primary technique used for dealing with low-speed bearing cases. Few studies employed vibration analysis because the signal generated as a result of the impact between the rolling element and the natural defect spots at low rotational speeds is generally weak and sometimes buried in noise and other interference frequencies. In order to increase the impact energy, some researchers generate artificial defects with a predetermined length, width, and depth of crack on the inner or outer race surfaces. Consequently, the fault frequency of a particular fault is easy to identify. This paper presents the applications of empirical mode decomposition(EMD) and ensemble empirical mode decomposition(EEMD) for measuring vibration signals slewing bearings running at a low rotational speed of 15 rpm. The natural vibration damage data used in this paper are obtained from a Korean industrial company. In this study, EEMD is used to support and clarify the results of the fast Fourier transform(FFT) in identifying bearing fault frequencies.

• Journal of the Korean Chemical Society
• /
• v.55 no.3
• /
• pp.346-353
• /
• 2011

Base hydrolysis of 7-hydroxy-2H-chromen-2-one (HC) and 7-hydroxy-2H-chromen-2-one-4-acetic acid (HCA) in aqueous-methanol and aqueous-acetone mixtures were studied kinetically at temperature range from 283 to 313 K. The activation parameters of the reactions were evaluated and discussed. Moreover, the change in the activation energy barrier of the investigated compounds from water to water-methanol and water-acetone mixtures was estimated from the kinetic data. It is observed that the change in activation barriers is more or less the same for the hydrolysis of HC and HCA. Base hydrolysis of HC and HCA follows a rate law with $k_{obs}=k_2[OH^-]$. The decrease in the rate constants of HC and HCA as the proportion of methanol or acetone increases is due to the destabilization of $OH^-$ ion. The high negative values of entropy of activation support the proposal mechanism, i.e. the investigated reaction takes place via the formation of an intermediate complex. Moreover, these values refer to the rigidity and stability of the intermediate complex. Thus, the ring opening of the intermediate complex would be the rate controlling step.

• Bulletin of the Korean Chemical Society
• /
• v.26 no.12
• /
• pp.1946-1952
• /
• 2005

New group 15 organometallic compounds, M$(phenanthrenyl)_3$ (M = P (1), Sb (2), Bi (3)) have been prepared from the reactions of 9-phenanthrenyllithium with $MCl_3$. A reaction of 9-(diphenylphosphino)phenanthrene with 2,6-diisopropylphenyl azide led to the formation of (phenanthrenyl)${(Ph)}_2P$=N-(2,6-$^iPr_2C_6H_3$) (4). The crystal structures of 2 and 4 have been determined by single-crystal X-ray diffractions, both of which crystallize with two independent molecules in the asymmetric unit. Compound 2 shows a trigonal pyramidal geometry around the Sb atom with three phenanthrenyl groups being located in a screw-like fashion with an approximately $C_3$ symmetry. A significant amount of CH- -$\pi$ interaction exists between two independent molecules of 4. The phosphorus center possesses a distorted tetrahedral environment with P-N bond lengths of 1.557(3)$\AA$ (P(1) N) and 1.532(3)$\AA$ (P(2)-N), respectively, which are short enough to support a double bond character. One of the most intriguing structural features of 4 is an unusually diminished bond angle of C-N-P, attributable to the hydrogen bonding of N(1)-H(5A) [ca. 2.49$\AA$ between two adjacent molecules in crystal packing. The compounds 1-3 show purple emission both in solution and as films at room temperature with emission maxima ($\lambda_{max}$) at 349, 366, and 386 nm, respectively, attributable to the ligand centered $\pi$ $\rightarrow$ $\pi^\ast$ transition in phenanthrene contributed by the lone pair electrons of the Gp 15 elements. Yet the nature of luminescence observed with 4 differs in that it originates from $\pi$ (diisopropylbenzene)-$\pi^\ast$ (phenanthrene) transitions with the $\rho\pi$contribution from the nitrogen atom. The emission maximum of 4 is red-shifted ranging 350-450 nm due to the internal charge transfer from the phenanthrenyl ring to the N-arylamine group as deduced from the ab initio calculations.