• Progress in Superconductivity and Cryogenics
• /
• v.4 no.1
• /
• pp.61-65
• /
• 2002

It becomes difficult and high in cost to construct new ducts and/or tunnels for power cables in metropolitan areas. This paper presents possible applications of an HTS superconducting power cables for transmitting electric power in metropolitan areas. Reflected were its important distinction such as compactness for installation in underground ducts and considerably high efficiency compared with present underground cables. In this paper, system modeling, transmission capacity and voltage class of compact HTS cables which should be applied to existing ducts were reviewed. Based on this, the following items on urban transmission system are examined. (1) A method of constructing a model system to introduce high temperature superconducting cables to metropolitan areas is presented. (2)The maximum outer diameter of HTS cables to be accommodated in exiting ducts is calculated based on the design standards for current cable ducts. (3)The voltage level that can be accommodated by existing ducts is examined.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.53 no.2
• /
• pp.76-81
• /
• 2004

This paper deals with characteristic analysis and experiments on components of low-Tc(LTS) power supply. A LTS power supply consists of two exciters, a rotor, a stator, and an LTS magnet. The power supply has eight rotating poles, which make rotational magnetic flux. These flux penetrate superconducting sheets and cause currents which charge an LTS load. In this experiment, a 25.8mH LTS magnet was used, and rotor revolutions from 30 to 300rpm were used. In order to measure the pumping-current with respect to the magnet flux changes, a hall sensor was installed at the center of the LTS magnet. The experimental observations have been compared with the theoretical predictions. In this experiment, the pumping-current has reached about 372A.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.50 no.4
• /
• pp.164-169
• /
• 2001

This paper deals with comparison of characteristics of continuous-sheet type low-Tc superconducting (LTS) power supply and discrete-sheet type LTS power supply. These characteristics have been analyzed through experiments. These power supplies consist of two exciters, a rotor, a stator, and a LTS load. A continuous-sheet type has a single continuous niobium (Nb) sheet attached to the inner surface of on the stator. In the case of discrete-sheet type, four separated Nb sheets are used. this experiment is using 1.81 mH LTS magnet load and maximum 30 A dc exciter current. A discrete-sheet type is expected to produce much better pumping rate than a continuous-sheet type. The experimental observations have been compared with the theoretical predictions. In this experiment, the maximum pumping-current has reached about 926 A.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2006.05a
• /
• pp.685-688
• /
• 2006

A single-phase uninterruptible power supply system suitable for a SMES unit is proposed to achieve a simple circuit configuration and higher system reliability. It reduces the number of switching devices by applying a common-arm scheme. Operational principles to normal, stored-energy, and bypass mode are discussed in detail. Eliminating some of the switches or substituting passive components for active switches generally increases the sophistication and reduces degree of freedom in control strategy. However, the high-performance digital controller ran execute the complicated control task with no additional cost. The validity of the proposed UPS system will be verified by a computer-aided simulation.

• Progress in Superconductivity and Cryogenics
• /
• v.5 no.1
• /
• pp.56-59
• /
• 2003

As electric power systems grow to supply the increasing electric power demand short-circuit current tends to increase and impose a severe burden on circuit breakers and power system apparatuses. Thus, all electric equipment in a power system has to he designed to withstand the mechanical and thermal stresses of potential short-circuit currents. Among current limiting devices, Fault Current Limiter (FCL) is expected to reduce the short-circuit current. Especially, Superconducting Fault Current Limiters (SFCL) offer ideal performance: in normal operation the SFCL is in its superconducting state and has negligible impedance, in the event of a fault, the transition into the normal conducting state passively limits the current. The SFCL using high-temperature superconductors offers a positive resolution to controlling fault-current levels on utility distribution and transmission networks. This study contributes to the EMTDC based modeling and simulation method of DC Reactor type SFCL. Single and three phase faults in the utility system with DC reactor type SFCLs have been simulated using EMTDC in order to coordinate with other equipments, and the results are discussed in detail.

• Progress in Superconductivity and Cryogenics
• /
• v.21 no.2
• /
• pp.22-25
• /
• 2019

The superconducting magnetic separation system has been developing to separate the iron oxide scale from the feed water of the thermal power plant. The accumulation in the boiler lowers the heat exchange rate or in the worst case damages it. For this reason, in order to prevent scale generation, controlling pH and redox potential is employed. However, these methods are not sufficient and then the chemical cleaning is performed regularly. A superconducting magnetic separation system is investigated for removing iron oxide scale in a feed water system. Water supply conditions of the thermal power plant are as follows, flow rate 400 t / h, flow speed 0.2 m / s, pressure 2 MPa, temperature $160-200^{\circ}C$, amount of scale generation 50 - 120 t / 2 years. The main iron oxide scale is magnetite (ferromagnetic substance) and its particle size is several tens ${\mu}m$. As the first step we are considering to introduce the system to the chemical cleaning process of the thermal power plant instead of the thermal power plant itself. The current status of development will be reported.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.888-889
• /
• 2011

As new one of superconducting power supplies, we proposed an HTS flux pump utilized a solar energy system. As an eternal electric energy can be converted by the solar system, the solar energy system is promisingly applied as an energy source in the power applications. A solar energy system is comprised of solar panel, photo-voltaic (PV) controller, converter and battery. The HTS flux pump consists of an electromagnet, two thermal heaters and a Bi-2223 magnet. In this paper, we describe the possibility the fusion technology between superconducting power supply and solar energy system. As a fundamental step, the fabrication, structure and experimental results are explained.

• Proceedings of the KIEE Conference
• /
• 2000.07b
• /
• pp.925-927
• /
• 2000

We fabricated a resistive superconducting fault current limiter of meander type based on a YBCO film. In order to disperse the heat generated at hot spots in the YBCO film the film was coated with a gold shunt layer. When diodes were inserted in the parallel circuit to restrict the temperature increase in the SFCL element by reducing power supply cycles, the voltage could be increased to $\sqrt{2}$ times with the same quench resistance at a half and full cycles.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11a
• /
• pp.343.2-343
• /
• 2002

Squeeze film dampers(SFDs) are designed and analyzed for radial superconducting bearings. The designed SFDs are mounted on the superconductors submerged in liquid nitrogen such that the dampers should supply additional damping to the relatively underdamped superconducting bearing support. Basic theory of SFD with superconducting bearing are introduced. Rotordynamic simulations are provided to support the feasibility of the superconducting magnetic bearings mounted on SFDs for a horizontal flywheel energy storage system.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.19 no.4
• /
• pp.328-332
• /
• 2007

A superconducting magnetic energy storage (SMES) system has shorter response time and longer life time, and is more economical, and environment-friendly than other uninterruptible power supply (UPS). A conduction cooling system is well answer for the high temperature superconductor (HTS) SMES system. Because the conduction cooling system is simple, light and small structure. The purpose of this paper is to design and verify the effective conduction cooling system for the HTS SMES system. The analysis of heat loads in cryostat is performed. Thermal shield heat loads, temperatures of HTS coil surface and conduction Cu plate are estimated and measured.