• Progress in Superconductivity
• /
• v.5 no.2
• /
• pp.105-108
• /
• 2004

We have studied effects of in-situ annealing on the fabrication of superconducting MgB$_2$ thin films prepared by rf magnetron co-sputtering. The Films were deposited on A1$_2$O$_3$ (1102) substrates at room temperature by using Mg and B targets. To trap remnant $O_2$ gas in the chamber, we used 20 mtorr Af sputter-gas balanced with 5 mol % of H$_2$ gas. To enhance adhesion to the substrate a thin layer of B was deposited prior to the codeposition of Mg and B. After completion of the film deposition, an additional Mg layer was deposited on top to compensate for Mg loss during the subsequent in-situ annealing. We have investigated the effects of two most important annealing parameters that are the Mg-to-B composition ratio and the annealing temperature. The range of the Mg-to-B composition ratio was from 0.42 to 0.85, and that of the annealing temperature was 500 $^{\circ}C$∼750 $^{\circ}C$. The Best result was obtained for the composition ratio of about 10% Mg excess from the stoichiometry and the annealing temperature of 700 $^{\circ}C$. Based on these results, we obtained films with T$_{c}$ : 36.5 K by further refining the fabrication process.s.

• Journal of Korean Society of Water and Wastewater
• /
• v.14 no.1
• /
• pp.37-44
• /
• 2000

Laboratory experiments were conducted to investigate the performances of anaerobic filters packed with ceramic tube and pall-ring media treating a dairy waste. The media packing volume was 65% of effective volume of anaerobic filter. Organics removals of anaerobic filters were maintained above 80% even at an organics loading rate of $10kgCOD/m^3/d$, and this was comparable to aerobic treatment of organic wastes. Organics removals of the ceramic tube anaerobic filters were always lower than those of the pall-ring anaerobic filters due to intrinsic physical property of ceramic tube, especially lower void space which caused to clogging and entrapment of biogas, substrate transfer limitation, and irregular evolution of biogas leading to loss of solids and biomass. This was clearly observed in higher concentration of TSS in the effluent from the ceramic tube anaerobic filter despite of higher retention capacity of TSS compared with pall-ring media. Vertical distribution of organics and solids in the filters showed above 90% of organics and solids in influent were removed below 20% of reactor height, and 50% of remaining organics and solids were removed though media packing zone. Effluent quality from the anaerobic filter was heavily depended on media itself as well as suspended biomass formed below media. It is therefore concluded that the type of media played an important role in biomass accumulation arid gas-liquid-solid separation efficiency. Type of media did not affect the start-up behaviors of the anaerobic filter, and supernatant from anaerobic digested sludge showed a good performance as a seeding materials.

• Journal of the Korean Ceramic Society
• /
• v.39 no.8
• /
• pp.742-749
• /
• 2002

The PZT thin films werre deposited on Pt/Ti/$SiO_2$/Si substrate by R. F. magnetron sputtering with $Pb_{1.1}Zr_{0.53}Ti_{0.47}O_3$ target. When interlayers(PbO, $TiO_2$, PbO/$TiO_2$) were inserted between PZT and Pt, the crystallization of the PZT thin films was considerably improved and the processing temperature was lowered. Compared to the pure PZT thin films, dielectric constant, dielectric loss and polarization properties of PZT thin films with interlayers were considerably improved. From XPS depth profile analysis, it was confirmed that PZT thin films and interlayers existed independently. In particular, PZT thin films deposited on interlayer(PbO/$TiO_2$) showed the best dielectric property (${\varepsilon}_r$=414.94, tan${\delta}$=0.0241, Pr=22${\mu}C/cm^2$).

• Journal of the Korean Ceramic Society
• /
• v.45 no.7
• /
• pp.411-417
• /
• 2008

Aerosol Deposition Method (ADM) is a novel technique to grow ceramic thick films with high density and nano-crystal structure at room temperature. $^{1,2)}$ For these unique advantages of ADM, it would be applied to the fabrication process of 3-D integration ceramic modules effectively. However, it is critical to control the properties of starting powders, because a film formation through ADM is achieved by impaction and consolidation of starting powders on the substrates. We fabricated alumina thick films by ADM for the application to integral substrates for RF modules. When the as-received alumina powders were used as a starting material without any treatments, it was observed that the dielectric properties of as-deposited alumina films, such as relative permittivity and loss tangent, showed high dependency on the frequency. In this study, some techniques of powder pre-treatments to improve the dielectric properties of alumina thick films will be shown and the effects of starting powders on the properties of AD films will be discussed.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.38 no.11
• /
• pp.49-54
• /
• 2001

In this work, we developed a Ka-band hybrid 4-stage power amplifier module using GaAs pHEMTs and waveguide to microstrip transitions. It has high gain and high output power characteristics. We used a 10 mil- thickness duroid substrate to fabricate this power amplifier and waveguide to microstrip transitions. The fabricated waveguide to microstrip transition showed about 1 dB insertion loss(back to back) at 32 40 GHz. The measured results of power amplifier module showed over 1W output power at 36.1 - 37.1 GHz. And it showed 31 dBm output power, 24 dB power gain and 15 % power-added efficiency(PAE) at 36.5 GHz.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.46 no.12
• /
• pp.14-21
• /
• 2009

In this paper, a Ka-band 10 W power amplifier module with seven power MMIC bare dies is designed and fabricated using MIC technology which combines multiple MMIC chips on a thin film substrate. Modified Wilkinson power dividers/combiners and CBFGCPW-Microstrip transitions for suppressing resonance and reducing connection loss are utilized for high-gain and high-power millimeter wave modules. A new TTL pulse timing control scheme is proposed to improve output power degradation due to large bypass capacitors in the gate bias circuit. Pulse-mode operation time is extended more than 200 nsec and output power increase of 0.62 W is achieved by applying the proposed scheme to the Ka-band 10 W power amplifier module operating in the pulsed condition of 10 kHz and $5\;{\mu}sec$. The implemented power amplifier module shows a power gain of 59.5 dB and an output power of 11.89 W.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.5
• /
• pp.528-537
• /
• 2011

In this paper, a broadband antenna of the CPW structure with a band-notched characteristic is presented. To obtain this characteristic, the complementary split ring resonator(CSRR) is inserted in the ground plane. In addition, the IEEE 802.11a WLAN band(5.15～5.825 GHz) appears in the band-notched characteristic. The proposed antenna dimension is $36{\times}60{\times}1.6\;mm^3$, and it is designed on the FR-4 substrate having a relative dielectric constant of 4.4. The designed antenna shows that the resonant frequency is 2.03～10.78 GHz below the return loss of -10 dB and a VSWR less than 2 was satisfied. As a result, the proposed CSRR has a band-notched characteristic in the range of 4.917～6.017 GHz which the center frequency is about 5.4 GHz band.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.11
• /
• pp.1225-1232
• /
• 2009

In this paper, a parabolic edge planar monopole antenna for indoor DTV reception is presented. The antenna has broadband property with the planar monopole and ground of parabolic edges. It is designed close to self-complementary structure as changing curvature of edges of monopole and ground. Monopole and ground conductors of the antenna are on the same plane, and excited through CPW feeding. It is fabricated on an FR4 dielectric substrate of $\varepsilon_r=4.4$, and the dimension is $40\;mm{\times}200\;mm{\times}1.6\;mm$. Return loss is larger than 10 dB in 470~806 MHz. Maximum gain is 1.86 dBi on E-plane at 810 MHz and 3.86 dBi on H-plane at 600 MHz.

• Journal of Advanced Navigation Technology
• /
• v.15 no.4
• /
• pp.549-555
• /
• 2011

In this paper, inverted triangle structural planar monopole antenna with Edge for UWB Communication (3.1 ~ 10.6 GHz) is presented. The antenna have broadband property structurally through inverted triangle structural planar monopole which have edge. Monopole and ground of proposed antenna exist on coplanar plane, and excite as CPW. It used FR4 dielectric substrate of ${\epsilon}_r=4.4$, and the size is $20{\times}20{\times}1.6mm$. Return loss is more than - 10dB in 3.1 ~ 10.1 GHz (7.0 GHz). Radiation pattern is about the same that of dipole antenna at all frequency. At measured result, max gain is 8.44 dBi at E - plane.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.5
• /
• pp.792-797
• /
• 2006

In this paper, an internal integrated microstrop patch for PCS handset is designed. To increase the bandwidth of microstrip patch antenna, a configuration of stacked type using parasitic element is used. Furthermore, to reduce the size of microstirip patch antenna, the main radiator in the substrate is shorted to the ground plane using five shorting-posts while three parasitic elements on the superstrate are also shorted to the ground plane using two shorting-posts respectively. The antenna bandwidth and radiation characteristics are calculated by HFSS 7.0 software, and compared with the experimental results. Experimental results show that the return loss is less than -10dB over the band of 1766MHz to 1900 MHz(134MHz) and the size of the fabricated microstrip patch antenna are $23\times20\times6.35mm$.