• Proceedings of the KIEE Conference
• /
• 2003.10a
• /
• pp.117-119
• /
• 2003

The $Pb(Zr_{0.3}Ti_{0.7)O_3/Pb(Zr_{0.7}/Ti_{0.3})O_3$ [PZT(30/70)/(70/30)] heterolayered thin films were deposited by RF sputtering method on the $Pt/TiO_2/SiO_2/Si$ substrate. Sputter gas ratio(AR/O2) was changed form 90/10 to 50/50. The structural properties and electrical properties of the PZT(30/70)/ (70/30) heterolayered thin films were studied. The relative dielectric constant and dielectric loss at 100Hz of the PZT(30/70)/PZT(70/30) heterolayered thin films with Ar/$O_2$(80/20) ratio were about 982 and 0.036, respectively.

• Transactions on Electrical and Electronic Materials
• /
• v.12 no.5
• /
• pp.222-225
• /
• 2011

Lead zirconate titanate (PZT) films were fabricated on Pt/Ti/$SiO_2$/Si substrate by the sol-gel method using a sol containing poly(N-vinylpyrrolidone) (PVP). PVP in alkoxide solutions can suppress the condensation reaction in gel films during heat treatment, and increase the viscosity of alkoxide solutions. Single-phase PZT films as thick as 1 ${\mu}m$ were deposited by repetitive coating with successive third-step heat treatments at 150$^{\circ}C$, 350$^{\circ}C$ and 650$^{\circ}C$. After heat treatment, the films were crack free, and optically transparent. As a result, we demonstrated a PZT film with a PVP molar ratio of 0.5, which has a permittivity of 734, a dielectric loss of 0.042, a $P_r$ of 40.5 ${\mu}C/cm^2$ and an $E_c$ of 156 kV/cm.

• Journal of Electrical Engineering and Technology
• /
• v.4 no.4
• /
• pp.527-530
• /
• 2009

$(Ba_{0.57}Sr_{0.33}Ca_{0.10})TiO_3$(=BSCT) powders, prepared by the sol-gel method, were doped using $MnCO_3$ as the acceptor and $Dy_2O_3$ as the donor. This powder was mixed with an organic vehicle. BSCT thick films were fabricated by the screen-printing techniques on the alumina substrate. The structural and dielectric properties of BSCT thick films were investigated with variation of the $Dy_2O_3$ amount. As a result of the differential thermal analysis (DTA), the exothermic peak was observed at around $670^{\circ}C$ due to the formation of the polycrystalline perovskite phase. All the BSCT thick films showed the XRD patterns of a typical polycrystalline perovskite structure. The average grain size of BSCT thick films decreased with an increasing amount of $Dy_2O_3$. The relative dielectric constant and dielectric loss of the BSCT thick film doped $Dy_2O_3$ 0.1mol% were 4637.4 and 1.6% at 1kHz, respectively.

• Proceedings of the KIEE Conference
• /
• 2008.10a
• /
• pp.171-172
• /
• 2008

$(Ba_{0.57}Sr_{0.33}Ca_{0.10})TiO_3$ (BSCT) thick films doped with 0.1 mol% $MnCO_3$ and $Yb_2O_3$ ($0.1{\sim}0.7$ mol%) were fabricated by the screen printing method on the alumina substrate. And the structural and electrical properties as a function of $Yb_2O_3$ amount were investigated. The lattice constants of the BSCT thick film doped with 0.1 mol% is 0.3955 nm. The specimen doped with 0.7 mol% $Yb_2O_3$ showed dense and uniform grains with diameters of about 6.3 mm. The thickness of all BSCT thick films was approximately 60 mm. The Curie temperature of the BSCT specimen doped with 0.1 mol% $Yb_2O_3$ was $18^{\circ}C$, and the dielectric constantand dielectric loss at this temperature was 4637 and 4.2%, respectively. The BSCT specimen doped with 0.1 mol% $Yb_2O_3$ showed the maximum value of $349{\times}10^{-9}C/cm^2K$ at Curie temperature. The figure of merit $F_D$ for specific detectivity of the specimens doped with 0.1 mol% $Yb_2O_3$ showed the highest value of $10.9{\times}10^{-9}Ccm/J$.

• Proceedings of the KIEE Conference
• /
• 2008.10a
• /
• pp.107-108
• /
• 2008

This article describes optimization for PGS(Patterned Ground Shield) of rectangular spiral inductor using Taguchi's Design of Experiment. PGS is decrease method of parasite component by silicon substrate among dielectric loss reduction method. Using taguchi's design of experiment, each parameter is fixed upon that PGS high poison(A), slot spacing(B), strip width(C) and overlap turn number(D) of PGS design parameter. Then we verified that percentage contribution and design sensitivity analysis of each parameter and level by signal to noise ratio of larger-the-better type. We consider percentage contribution and design sensitivity of each parameter and level, and then verify that model of optimization for PGS is lower inductance decreasing ratio and higher Q-factor increasing ratio by EM simulation.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.43 no.2
• /
• pp.296-302
• /
• 1994

Polycrystalline CuInSeS12T thin were prepared by depositing Cu/In layer, which was sequentially sputtered varying the Cu/(Cu+In) mole ratio, on glass substrate and selenizing with selenium metal vapor in a nitrogen atmosphere. Compositional and structural, characterization was carried out by X-ray diffraction (XRD), wavelength-dispersive spectroscopy(WDS), and scanning electron microscope(SEM). Electrical characterization was carried out by the measurements of Hall effect, electrical resistivity. Large indium loss occurs in early stage of the selenization process. The selenized films which had mole ratios larger than 0.28 have chalcopyrite CuInSeS12T phase and these that had less mole ratios have sphalerite phase. The selenized films containing CuS1xTSe phase have Cu-rich CuInSeS12T phase and these that did not contain CuS1xTSe have In-rich CuInSeS12T phase. By optimizing the sputtering conditions,it is possible to fabricate CuInSeS12T thin films which have little secondary phases and an appropriate hole concentration (10S015T ~ 10S016TcmS0-3T) for solar cells.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.05b
• /
• pp.42-45
• /
• 2001

The high permittivity are applied to DRAM and FRAM. (Ba,Sr)$TiO_3$ (EST) thin films were prepared by Sol-Gel method. BST solution was made and spin-coated on $Pt/SiO_2/Si$ substrate at 4000 [rpm] for 10 seconds in a time coating. Coated specimens were dried at $90[^{\circ}C]$ for 5 minutes. Coating process was repeated from 3 times to 5 times and then sintered at $750[^{\circ}C]$ for 30 minutes. Each specimen was analyzed structure and electrical characteristics. Thickness of BST ceramics thin films are about 2600-2800[$\AA$] in 3 times. Dielectric constant of thin films was little decreased at 1[KHz]~1[MHz]. Dielectric constant and loss to frequency were 250 and 0.02 in BST3. The property of leakage current was stable When the applied voltage was 0~3[V] Leakage current was $10^{9}\sim10^{11}$[A] at 0~3[V].

• Proceedings of the SCSK Conference
• /
• 2003.09a
• /
• pp.590-600
• /
• 2003

The matrix metalloproteinases (MMPs) are a family of enzymes responsible for degrading connective tissue. MMPs catalyze the breakdown of collagen from the extracellular matrix, leading to wrinkle formation and accelerated skin aging. Furthermore, ultraviolet irradiation causes increased expression of certain MMPs. In the extracellular matrix turnover, MMPs are interacting with endogenous regulators named tissue inhibitors of metalloproteinases (TIMPs). Using peptide substrate assays, it has been demonstrated that TIMP-MMP complexes interact highly specifically with $K_{i}$ values of 10$^{-9}$ -10$^{-16}$ M. Therefore applications for TIMP as inhibitor of collagen degradation are suggested for cosmetic anti-aging products to prevent wrinkle formation and loss of elasticity. To date four TIMP proteins (TIMP-1, TIMP-2, TIMP-3 and TIMP-4) have been identified which show a high degree in sequence similarity. The production of human TIMP-2, a 194-residue nonglycosylated protein, was performed by fed-batch culture of Escherichia coli. TIMP-2 accumulated in the bacterial cells in an insoluble form as inclusion bodies. The inclusion bodies were solubilized and the protein refolded to yield the native TIMP-2 in the active form. The integrity of the protein was confirmed by mass analysis, Edman sequencing and gel shift experiments with authentic samples. The inhibitory activity of the refolded and purified TIMP-2 was demonstrated with MMP-1 and MMP-2 assays using synthetic fluorogenic peptide substrates.s.

• Mycobiology
• /
• v.33 no.3
• /
• pp.147-149
• /
• 2005

The investigation was undertaken to enhance the decomposition process by pre-treatment of rice stubble, having higher concentration of lignin. Air-dried rice stubble was treated with 1.8 liter of 1% NaOH and autoclaved. Six cellulolytic fungi, Trichoderma harzianum, Penicillium citrinum, Curvularia lunata, Aspergillus flavus and Alternaria alternata were grown in basal synthetic medium along with delignified rice-residue as carbon source for production of soluble crude protein. Though the loss of cellulose has been observed by all of them but having a considerable status in the presence of T. harzianum and T. harzianum yielded highest percentage of crude protein (27.99%) with biomass of 375 mg, whereas the lowest protein value (17.91%) was recorded in case of A. niger with biomass of 422 mg. Among the imperfect fungi, T. harzianum was the most potent. Effects of incubation period and nitrogen sources on soluble crude protein production by T. harzianum were also undertaken in this study. Fifth day of incubation period and potassium nitrate as nitrogen source among other nitrogen sources was found most appropriate for soluble crude protein production by the mentioned organism.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.1
• /
• pp.48-58
• /
• 2015

The bandwidth enhancement of an aperture coupled microstrip patch antenna(ACMPA) with a high permittivity feed substrate suitable for the integration with MMIC is investigated using variation of an aperture width. As an aperture width increases, the 10 dB return loss bandwidth increases due to the increase of the mutual resonance region between a patch resonance and an aperture resonance. The bandwidth of an ACMPA with extended aperture width is increased up to 35.3 % from 20.8 % of the ACMPA with an aperture of a typical aspect ratio 10:1. The degradation of the radiation characteristics of an ACMPA due to the increase of an aperture width is very small.