• Korean Journal of Materials Research
• /
• v.19 no.3
• /
• pp.132-136
• /
• 2009

This study investigates GaAs dry etching in capacitively coupled $BCl_3/N_2$ plasma at a low vacuum pressure (>100 mTorr). The applied etch process parameters were a RIE chuck power ranging from $100{\sim}200W$ on the electrodes and a $N_2$ composition ranging from $0{\sim}100%$ in $BCl_3/N_2$ plasma mixtures. After the etch process, the etch rates, RMS roughness and etch selectivity of the GaAs over a photoresist was investigated. Surface profilometry and field emission-scanning electron microscopy were used to analyze the etch characteristics of the GaAs substrate. It was found that the highest etch rate of GaAs was $0.4{\mu}m/min$ at a 20 % $N_2$ composition in $BCl_3/N_2$ (i.e., 16 sccm $BCl_3/4$ sccm $N_2$). It was also noted that the etch rate of GaAs was $0.22{\mu}m/min$ at 20 sccm $BCl_3$ (100 % $BCl_3$). Therefore, there was a clear catalytic effect of $N_2$ during the $BCl_3/N_2$ plasma etching process. The RMS roughness of GaAs after etching was very low (${\sim}3nm$) when the percentage of $N_2$ was 20 %. However, the surface roughness became rougher with higher percentages of $N_2$.

• The Korean Journal of Mycology
• /
• v.42 no.3
• /
• pp.219-224
• /
• 2014

A gram-negative bacterium was isolated from spent substrate of Agaricus bisporus and showed marked antagonistic activity against Pseudomonas tolaasii. The bacterium was identified as Pseudomonas azotoformans by based on the cultural, biochemical and physiological characteristics, and 16S rRNA gene sequence. The isolated bacterium was saprophytic but not parasitic nor pathogenic to cultivation mushroom. The isolated bacterium for P. tolaasii cell was not sufficient for inhibition in vitro. Control efficacy of Pseudomonas azotoformans HC5 to brown blotch of P. tolaasii was 73, 78, and 71% on A. bisporus, Flammulina velutipes, and Pleurotus ostreatus, respectively. In the future, the suppressive bacterium may be useful for development of a biocontrol system.

• Korean Journal of Materials Research
• /
• v.9 no.11
• /
• pp.1129-1136
• /
• 1999

TIN films were prepared on Si(100) substrate by ICP-CVD(inductive1y coupled plasma enhanced chemical vapor deposition) using TEMAT(tetrakis ethylmethamido titanium : Ti$[\textrm{N}\textrm{(CH)}_{3}\textrm{C}_{2}\textrm{H}_{5}]_{4}$) precursor at various deposition conditions. Phase, microstructure, and the electrical properties of TIN films were characterized by x-ray diffraction (XRD), x-ray photoelectron spectroscopy (XPS), high resolution transmission electron microscopy (HRTEM) and electrical measurements. Polycrystalline TiN films with B1 structure were grown at temperatures over $200^{\circ}C$. Preferentially oriented along TiN(111) films were obtained at temperatures over $300^{\circ}C$ with the flow rates of 10, 5, and 5 sccm for TEMAT, $\textrm{N}_{2}$ and Ar gas. The TiN/Si(100) interface was flat and no chemical reaction between TIN and $\textrm{SiO}_2$ was found. The resistivity, carrier concentration and the carrier mobility for the TiN sample prepared at $500^{\circ}C$ are 21 $\mu\Omega$cm, 9.5$\times\textrm{10}^{18}\textrm{cm}^{-3}$ and $462.6\textrm{cm}^{2}$/Vs, respectively.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.183-184
• /
• 2013

Two main MBE growth techniques have been used: plasma-assisted MBE (PA-MBE), which utilizes a rf plasma to supply active nitrogen, and ammonia MBE, in which nitrogen is supplied by pyrolysis of NH3 on the sample surface during growth. PA-MBE is typically performed under metal-rich growth conditions, which results in the formation of gallium droplets on the sample surface and a narrow range of conditions for optimal growth. In contrast, high-quality GaN films can be grown by ammonia MBE under an excess nitrogen flux, which in principle should result in improved device uniformity due to the elimination of droplets and wider range of stable growth conditions. A drawback of ammonia MBE, on the other hand, is a serious memory effect of NH3 condensed on the cryo-panels and the vicinity of heaters, which ruins the control of critical growth stages, i.e. the native oxide desorption and the surface reconstruction, and the accurate control of V/III ratio, especially in the initial stage of seed layer growth. In this paper, we demonstrate that the reliable and reproducible growth of GaN on Si (110) substrates is successfully achieved by combining two MBE growth technologies using rf plasma and ammonia and setting a proper growth protocol. Samples were grown in a MBE system equipped with both a nitrogen rf plasma source (SVT) and an ammonia source. The ammonia gas purity was ＞99.9999% and further purified by using a getter filter. The custom-made injector designed to focus the ammonia flux onto the substrate was used for the gas delivery, while aluminum and gallium were provided via conventional effusion cells. The growth sequence to minimize the residual ammonia and subsequent memory effects is the following: (1) Native oxides are desorbed at $750^{\circ}C$ (Fig. (a) for [$1^-10$] and [001] azimuth) (2) 40 nm thick AlN is first grown using nitrogen rf plasma source at $900^{\circ}C$ nder the optimized condition to maintain the layer by layer growth of AlN buffer layer and slightly Al-rich condition. (Fig. (b)) (3) After switching to ammonia source, GaN growth is initiated with different V/III ratio and temperature conditions. A streaky RHEED pattern with an appearance of a weak ($2{\times}2$) reconstruction characteristic of Ga-polarity is observed all along the growth of subsequent GaN layer under optimized conditions. (Fig. (c)) The structural properties as well as dislocation densities as a function of growth conditions have been investigated using symmetrical and asymmetrical x-ray rocking curves. The electrical characteristics as a function of buffer and GaN layer growth conditions as well as the growth sequence will be also discussed. Figure: (a) RHEED pattern after oxide desorption (b) after 40 nm thick AlN growth using nitrogen rf plasma source and (c) after 600 nm thick GaN growth using ammonia source for (upper) [110] and (lower) [001] azimuth.

• Journal of Wetlands Research
• /
• v.16 no.3
• /
• pp.303-313
• /
• 2014

The spatial distribution characteristic of fish community were investigated at the 10 habitat types in the Nonsan stream from August, 2008 to June, 2009. The collected species during the surveyed period were 26 species belong to 6 families. Korean endemic species were Sarcocheilichthys nigripinnis morii, Squalidus japonicus coreanus, Hemiculter eigenmanni, Pseudobagrus koreanus, and Odontobutis interrupta which showed 19.2% ratio of total species. Dominant species was Zacco platypus, and subdominant species was Tridentiger brevispinis. Dominant species according to habitat types were Micropterus salmoides(substrate type pool and rock type pool), Lepomis macrochirus(channel connected pool and channel unconnected pool/abandoned type pool), T. brevispinis(channel unconnected pool/overflow type and run) and Z. platypus(riffle, meander type pool, side channel, and dam type pool). As a results of community analysis in side channel, diversity index showed relatively high values, indicating that habitat types in the Nonsan stream have relatively stable community structure. Bray-curtis cluster analysis indicated that the meander type pool and riffle showed the most similar values(80.8%). Moreover, cluster and principal component analysis were classified as 2 groups(lotic and lentic habitats).

• Membrane Journal
• /
• v.28 no.5
• /
• pp.307-319
• /
• 2018

Ion-exchange membrane (IEM) has fixed charge groups and is a separation membrane which is capable of selectively transporting ions of the opposite polarity. Recently, the interest in IEMs has been increasing as the importance of the desalination and energy conversion processes using them as the key components has increased. Since the IEMs determine the efficiency of the above process, it is necessary to improve the separation performance and durability of them and also to lower the expensive membrane price, which is a hindrance to the widening application of the IEM process. Therefore, it is urgent to develop high-performance and low-cost IEMs. Among various types of IEMs, pore-filled membranes prepared by filling ionomer into a porous polymer substrate are intermediate forms of homogeneous membranes and heterogeneous membranes. The production cost would be cheap like the case of heterogeneous membranes because of the use of inexpensive supports and the reduction of the amount used of raw materials, and at the same time, they exhibit excellent electrochemical characteristics close to homogeneous membranes. In this review, major research and development trends of pore-filled IEMs, which are attracting attention as high-performance and low-cost IEMs, have been summarized and reported according to the application fields.

• Korean Journal of Materials Research
• /
• v.8 no.5
• /
• pp.377-382
• /
• 1998

Atomic layer deposition(ALD) of amorphous TiN films on $SiO_2$ between 17$0^{\circ}C$ and 21O$^{\circ}C$ has been investigated by alternate supply of reactant sources, Ti[N($C_2,H_5,CH_3)_2]_4$ [tetrakis(ethylmethylamminoltitanium: TEMAT] and $NH_3$. Reactant sources were injected into the reactor in the order of TEMAT vapor pulse, Ar gas pulse, $NH_3$. gas pulse and Ar gas pulse. Film thickness per cycle was saturated at around 1.6 monolayer(MU per cycle with sufficient pulse times of reactant sources at 20$0^{\circ}C$. The results suggest that film thickness per cycle could be beyond 1 MLicycie in ALD, which were explained by rechemisorption mechanisms of reactant sources. The ideal linear relationship be¬tween number of cycles and film thickness is confirmed. As a results of surface limited reactions of ALD, step cover¬age was excellent. Particles caused by the gas phase reactions between TEMAT and NH3 were almost free because TEMAT was seperated from $NH_3$ by the Ar pulse. In spite of relatively low substrate temperature, carbon impurity was incorporated below 4 at%.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2001.06a
• /
• pp.8-8
• /
• 2001

초고속 증착은 짧은 시간에 박막 형성을 가능하게 하므로 window glass 코팅등의 대면적 코팅에 있어서 비용을 절감 시키고, 대량생산을 가능하게 만들기 때문에 관심이 집중되고 있다. 고속증착 공정으로는 high current arc, laser arc, hollow cathode discharge ion plating 그리고 마그네트론 스퍼터링법 등이 있다. 특별히 마그네트론 스퍼터링법은 3m이상의 넓이에 코팅을 할때 두께가 매우 균일하며, 증착율은 evaporation 공정에 비해 경제적, 기능적인 면에서 효율적이다. 그리고 증착된 박막은 매우 조밀하고 좋은 밀착력을 갖고 있으며, 고융점 금속을 포함하여 금속 합금 및 혼합물의 비율을 조정 및 금속 산화물, 질화물, 탄화물 등과 같은 금속의 증착도 stoichiometry를 조정하여 박막을 합성 시키는데 있어서 효과적이다. 이러한 초고속 증착을 만들기 위한 마그네트론 스퍼터링법의 요건은 마그네트론 원이 높은 타켓 power density를 가져야 하며, 타켓에서 효율적으로 플라즈마를 구속하여 스퍼터 되는 이온의 양을 최대화 시킬 수 있어 한다. 따라서 본 실험에서는 초고속 증착을 위해서 직경 50mm 타켓의 UBM magnetron원을 설계 제작하였다. 고밀도의 플라즈마를 형성시키기 위해서, Poisson simulation c code를 이용하여 자기장의 방향, 세기 및 밀도를 측정 하였고, 자기장 측정기(Gauss meter)를 이용하여 실제 자장을 측정 비교 분석하였다. 상기의 data를 바탕으로 여러 형상의 마그네트론원을 설계, 제작하였고. 마그네트론 원의 특성 분석을 위해 I-V 방전 특성을 평가하였고 substrate ion current density와 박막의 증착율을 측정하였다.duty-on 시간의 증가에 따라 $Cr_2N$ 상의 형성이 점점 많아져 80% duty-on 시간 경우에는 거의 CrN과 $Cr_2N$ 상이 공존하는 것으로 나타났다. 또한 duty-on 시간이 증가할수록 회절피크의 세기가 증가하여 결정화가 더 많이 진행되어짐을 알 수 있었다. 마찬가지로 바이어스 펄스이 주파수에 다른 결정성의 변화도 펄스의 주파수가 증가할수록 박막이 결정성이 좋아지고 $Cr_2N$ 상이 쉽게 형성되었다. 증착 진공도에 따른 결정성은 상대적으로 질소의 농도가 높은 낮은 진공도에서는 CrN 상이 주로 형성되었으며, 반대로 높은 진공도에서는 $Cr_2N$ 상이 많이 만들어졌다. 즉 $1.3{\times}10^{-2}Torr$의 증착 진공도에서는 CrN 상만이 보이는 반면 $9.0{\tiems}1-^{-2}Torr$ 진공도에서부터 $Cr_2N$ 상이 형성되기 시작하여 $5.0{\tiems}10^{-2}Torr$ 진공도에서는 두개의 상이 혼재되어 있음을 알 수 있었다. 박막의 내마모성을 조사한 결과 CrN 박막의 마찰 계수는 초기에 급격하게 증가한 후 0.5에서 0.6 사이의 값으로 큰 변화를 보이지 않았으며, $Cr_2N$ 박막도 비슷한 거동을 보였다.차 이, 목적의 차이, 그리고 환경의 의미의 차이에 따라 경관의 미학적 평가가 달라진 것으로 나타났다.corner$적 의도에 의한 경관구성의 일면을 확인할수 있지만 엄밀히 생각하여 보면 이러한 예의 경우도 최락의 총체적인 외형은 마찬가지로 $\ulcorner$순응$\lrcorner$

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.5
• /
• pp.491-498
• /
• 2005

J sewage treatment plant (WWTP) in Busan has used methanol as an external carbon source for the biological denitrification process. Methanol is widely used. but rather expensive and very dangerous in handling. Therefore, it has been required that the economic alternative carbon source must be developed. By-product from a fine chemical industry can be Purified by removing high molecular weight substances using the ultrafilter membrane separation process and RBDCOD fraction becomes $98{\sim}99%$ of COD substances in the purified by-product. The purified by-product containing three types of alcohols, methanol, prophylenglycol and methoxypropanol; showed similar chemical characteristics to the methanol, a main external carbon source, in biodegradation pathway. Shown above, the compatibility between main and alternative carbon sources has been achieved. Also very short or no adaptation period is necessary in the case of exchanging these carbon sources. The compatibility between external carbon sources is an essential element for stabilizing WWTP operations. During the full-scale application test of the by-product, the alternative carbon source line got on par with the treatment efficiency of the methanol line. With the test result, J-WWTP changed methanol to a fine chemical by-product, in two out of three J-WWTP lines. Moreover, it is expected that 55.4% of the external carbon source cost reduction can be achieved in the alternative carbon source applied lines.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.157-157
• /
• 2016

최근 많은 산업의 발전으로 인해 환경오염을 유발시키는 폐수가 다량으로 배출되고 있으며, 이러한 폐수 속에는 유기용매, 고분자 물질 및 각종 염 등의 난분해성 물질들이 다량으로 함유되어 있다. 이런 물질들을 분해시키기 위해 물리적, 생물학적 수처리 방법이 많이 이용되고 있지만 이 방법들은 각각 운전비용과 처리비용이 고가인 단점이 있다. 따라서 비용과 효율 측면에서 효과적인 폐수처리를 위해서 전기화학적 폐수처리 방법이 많이 사용되고 있다. 물리적, 생물학적 처리 방법에 비해 비용이 적게 들고, 처리 후 잔류물이 남지 않으며. 독성을 띄는 산화제의 첨가 없이도 높은 폐수처리 능력을 보이기 때문에 친환경적이므로, 전기화학적 폐수산화 처리에 사용되는 불용성 전극에 대한 연구가 많이 진행되어져 오고 있다. 그 중 BDD(Boron-doped diamond) 전극은 표면에서 강력한 산화제인 수산화 라디칼의 높은 발생량으로 인해 뛰어난 폐수처리 능력을 보이므로 불용성 전극 분야에서 활발한 연구가 진행 중이다. 그러나 기존에 BDD 전극의 기판 모재로 이용되던 Si, W, Pb등은 모두 기계적 강도. 폐수처리 능력 및 독성 문제로 인해 한계가 있었고, 특히 Nb기판 위에 형성시킨 BDD 전극은 뛰어난 폐수처리 능력에도 불구하고 비싼 모재 원가로 인해 상용화가 힘든 실정이다. 이런 문제점을 해결하기 위해 높은 기계적 강도와 전기화학적 안정성을 가진 Ti 기판을 사용한 BDD 전극에 대한 연구가 보고되고 있다. 그러나 BDD와 Ti 간의 lattice mismatch, BDD층 형성을 위한 고온 공정 시 탄소의 확산으로 인한 기판 표면에서의 TiC층 형성으로 인해 접착력이 감소하여 박리가 생기는 문제점이 있다. BDD와 Ti의 접착력을 향상시키기 위해 융점이 높고, 전기전도성이 우수한 TiN을 diffusion barrier layer로 삽입하면 탄소 확산에 의한 TiC층의 생성을 억제하여, 내부응력에 기인한 접착력 감소를 방지할 수 있다. 또 하나의 방법으로 Ti 기판의 전처리를 통해 BDD층의 접착력을 향상 시킬 수 있다. Sanding과 etching을 통해 기판 표면의 물리, 화학적인 표면조도를 부여하고, seeding을 통해 diamond 결정 성장에 도움을 주는 seed 입자를 분포시킴으로써, 중간층과 BDD층의 접착력을 향상시키고, BDD 결정핵 성장을 촉진시켜 고품질의 BDD박막 증착이 가능하다. 본 연구에서는 기존 Si, Nb 등의 기판 모재를 Ti로 대체함으로써 제조원가를 절감시키고, TiN 중간층을 삽입하여 접착력을 향상시킴으로써 기존의 BDD 전극과 동등한 수준의 물성 및 수처리 특성을 가진 BDD전극 제작을 목표로 하였다. $25{\times}25mm$의 Ti 기판위에 TiN 중간층을 DC magnetron sputtering을 이용하여 증착 후, BDD 전극 층을 HFCVD로 증착하였다. 전처리를 진행한 기판과 중간층 및 BDD층의 미세구조를 XRD로 분석하였고, 표면 형상을 SEM으로 확인하였다. BDD전극의 접착력 분석을 통해 TiN 중간층의 최적 조성을 도출하고, 최종적으로 BDD/TiN/Ti 전극의 CV특성과 가폐수의 COD분해능력 및 축산폐수, 선박평형수 등의 실제 폐수 처리 능력을 BDD/Si, BDD/Nb 전극과 비교 검토할 것이다.