• Journal of the Korean institute of surface engineering
• /
• v.41 no.6
• /
• pp.287-291
• /
• 2008

Reactively magnetron sputtered TiN films were deposited on Si wafers under varying bias voltage and characterized by X-ray diffraction, field-emission scanning electron microscopy and Nanoindentation. The films deposited under an Ar + $N_2$ atmosphere exhibited a mixed (200)-(111) orientation with a strong (200) texture, which subsequently changed to a strong (111) texture with increasing bias voltage. The changes in texture and grain size of the TiN thin films are due to one or a combination of factors such as strain energy, surface free energy, surface diffusivity and adatom mobility. The influence of each factor depends on the processing conditions. The average deposition rate and grain size were calculated from FE-SEM images of the films indicating that the deposition rate was lower at the films deposited under bias voltage.

• Journal of the Korean institute of surface engineering
• /
• v.28 no.6
• /
• pp.343-351
• /
• 1995

Titanium nitride films have been prepared on various substrates (silicon wafer, HSS) by cathode arc ion plating process to measure microhardness, adhesion and wear-resistant behaviors by changing the substrate bias voltages (0∼-300V), thickness and roughness. Microhardnesses were measured by micro vickers hardness tester, the adhesion strengths were evaluated by acoustic signals through the scratch test with incremental applied load. As the substrate bias voltages were increased, the ｛111｝ orientation was predominant, the microhardnesses and adhesion strengths of tool steel were observed to be stronger than those of without subatrate bias voltage. Adhesion strengths of the substrate bias were 4-7 times higher than those of without the substrate bias, confirmed by SEM with EDX. Wear resistances were used pin-on-disk tribotester and TiN costing reduced the abrasive wear. As the substrate bias was increased, the weight loss and the friction coefficient was decreased.

• The Korean Journal of Ceramics
• /
• v.3 no.3
• /
• pp.182-186
• /
• 1997

Diamond-like carbon(DLC) films were deposited on silicon substreates by using an RF plasmaassisted CVD apparatus; the effects of deposition conditions such as CH4 gas pressure and substrate bias voltage on DLC film friction and wear were examined in both friction and scratch tests. In friction tests critical loads at which the friction coefficient increases abruptly depend on substrate bias voltages: critical loads deposited at a bias voltage of -100 V exceed those deposited at other bias voltages. Critical loads are correlated with DLC film hydrogen content. Critical DLC film loads in scratch tests depended considerably less than in friction tests. The friction coefficient of DLC films depends on neither substrate bias voltage nor CH4 gas pressure.

• The Korean Journal of Ceramics
• /
• v.2 no.4
• /
• pp.197-202
• /
• 1996

The highly oriented diamond particles were deposited on the mirror-polished (100) silicon substrates in the bell-jar type microwave plasma deposition system using a three-step process consisting if carburization, bias-enhanced nucleation and growth. By adjusting the geometry of the substrate and substrate holder, very dense disc-shaped plasma was formed over the substrate when the bias voltage was below -200V. Almsot perfectly oriented diamond films were obtained only in this dense disc-shaped plasma. From the results of the optical emission spectra of the dense disc-shaped plasma, it was found that the concentrations of atomic hydrogen and hydrocarbon radical were increased with negative bias voltage. It was also found that the highly oriented diamonds were deposited in the region, where the intensity ratios of carbonaceous species to atomic hydrogen are saturated.

• Journal of the Korean institute of surface engineering
• /
• v.36 no.2
• /
• pp.148-154
• /
• 2003

Short ($\tau$=40 $mutextrm{s}$) and high-voltage ($U_{sub}$=2~8 kV) negative substrate bias pulses were used to assist pulsed magnetron sputtering DLC films deposition. Space- and time-resolved probe measurements of the plasma characteristics have been performed. It was shown that in case of high-voltage substrate bias spatial non-uniformity of the magnetron discharge plasma density greatly affected DLC deposition process. By Raman spectroscopy it was found that maximum percentage of s $p^3$-bonded carbon atoms (40 ~ 50%) in the coating was attained at energy $E_{c}$ ~700 eV per deposited carbon atom. Despite rather low diamond-like phase content these coatings are characterized by good adhesion due to ion mixing promoted by high acceleration voltage. Short duration of the bias pulses is also important to prevent electric breakdowns of insulating DLC film during its growth.wth.

• Proceedings of the KIEE Conference
• /
• 1996.11a
• /
• pp.206-208
• /
• 1996

Thin films of magnesium oxide(MgO) were deposited on glass substrates by RF magnetron sputtering method. The characteristics of MgO thin films were analyzed as a function of various deposition conditions such as substrate temperature, substrate self-bias, input power and pressure. As the substrate temperature and bias voltage were increased, the grain size of MgO thin film increased. XRD peaks of (111) and (222) direction became dominant, as the substrate bias voltage increases and temperature decreases.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.258-258
• /
• 2010

In this work, back bias effects in the program of the silicon-oxide-nitride-oxide-silicon (SONOS) cell using two-step pulse sequence, are investigated. Two-step pulse sequence is composed of the forward biases for collecting the electrons at the substrate terminal and back bias for injecting the hot electrons into the nitride layer. With an aid of the back bias for electron injection, we obtain a program time as short as 600 ns and an ultra low-voltage operation with a substrate voltage of -3 V.

• Journal of the Korean Electrochemical Society
• /
• v.6 no.4
• /
• pp.261-265
• /
• 2003

The heat treatment process of thin film microbatteries manufacturing processes has several Problems. This study, without heat treatment, considered the characteristics of $LiCoO_2$ thin films deposited by bais sputtering method inducing the structural change of the thin film. The properties of deposited $LiCoO_2$ thin films such as crystal structure, morphology, and discharge capacity were observed by various analysis methods. Among $LiCoO_2$ thin films deposited by substrate bias $voltage(V_b)$, the one deposited by substrate bias voltage of -50V had the highest initial discharge capacity of about $60{\mu}Ah/cm^2{\mu}m.$ We confirmed that $LiCoO_2$ thin film could be used as cathode material of lithium thin film microbatteries without annealing.

• The Korean Journal of Ceramics
• /
• v.3 no.3
• /
• pp.159-162
• /
• 1997

Diamond was uniformly nucleated on large area Si(001) substrate (3cm$\times$4cm) using the low pressure magnetoactive microwave plasma chemical vapor deposition. $CH_4/He$ gas mixture was used as source gas in order to obtain high radical density in the nucleation enhancement step. $CH_3$radical density was measured by means of infrared laser absorption spectroscopy. The effect of substrate bias voltage on diamond nucleation was examined. The results showed that a suitable positive bias voltage appled to the substrate with respect to the chamber could enhance diamond nucleation while a negative bias voltages leaded to deposition of only non-diamond phase carbon.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2007.11a
• /
• pp.136-137
• /
• 2007

Wear resistant TiAlN thin film has been widely deposited on the surface of cutting and forming tools by using Arc Ion Plating. TiAlN films are deposited by the processes designed by the Taguchi L18 experimental design. The L18 experimental design is applied to achieve surface properties and adhesion. The deposition parameters are working pressure, substrate temperature, bias voltage, arc power and pre-sputtering bias voltage and time. The most influential parameters on surface properties and adhesion are substrate bias voltage, working nitrogen pressure and arc power. The optimal coating processes are obtained for surface properties and adhesion.