• Advances in aircraft and spacecraft science
• /
• 제6권4호
• /
• pp.283-296
• /
• 2019

The influence of different planform parameters on the aerodynamic performance of large-scale subsonic and transonic Blended Wing Body (BWB) aircraft have gained comprehensive research in the recent years, however, it is not the case for small-size low subsonic speed Unmanned Aerial Vehicles (UAVs). The present work numerically investigates aerodynamics governing four different trailing edge geometries characterizing BWB configurations in standard flight conditions at angles of attack from $-4^{\circ}$ to $22^{\circ}$ to provide generic information that can be essential for making well-informed decisions during BWB UAV conceptual design phase. Simulation results are discussed and comparatively analyzed with useful implications for formulation of proper mission profile specific to every BWB configuration.

• Advances in aircraft and spacecraft science
• /
• 제6권1호
• /
• pp.19-30
• /
• 2019

Two- and three-dimensional turbulent airflows in a 9-degrees-bent channel are studied numerically. The inner surfaces of upper and lower walls are parallel to each other upstream and downstream of the bend section. The free stream is supersonic, whereas the flow at the channel exit is either supersonic or subsonic depending on the given backpressure. Solutions of the Reynolds-averaged Navier-Stokes equations are obtained with a finite-volume solver ANSYS CFX. The solutions reveal instability of formed shock waves and a flow hysteresis in considerable bands of the free-stream Mach number at zero and negative angles of attack. The instability is caused by an interaction of shocks with the expansion flow formed over the convex bend of lower wall.

• 한국분무공학회지
• /
• 제24권1호
• /
• pp.27-34
• /
• 2019

An experimental study on the spray characteristics of aerated-liquid jets discharged from effervescent injectors to a subsonic crossflow was conducted to investigate effects of a gas to liquid mass ratio (GLR) and a ratio of the orifice length to the diameter (L/d). The present effervescent injectors consist of a plain orifice injector and an aerator. To analyze breakup length and spray trajectory, instantaneous spray images were taken by a high speed camera. As the GLR increased, the spray penetration became higher under the same liquid mass flow rate and the breakup length became shorter due to the bubble expansion or the annular liquid film breakup. To predict the spray trajectory of two-phase flow jets into the crossflow, the homogeneous and the separated flow models were compared.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2008년도 12th Asian Congress of Fluid Mechanics
• /
• pp.57.3-57.3
• /
• 2008

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2002년도 제19회 학술발표대회 논문초록집
• /
• pp.5-5
• /
• 2002

• International Journal of Aeronautical and Space Sciences
• /
• 제13권3호
• /
• pp.386-397
• /
• 2012

The stability and structure of bluff-body stabilized hydrogen flames were investigated numerically and experimentally. The velocity of coflowing air was varied from subsonic velocity to a supersonic velocity of Mach 1.8. OH PLIF images and Schlieren images were used for analysis. Flame regimes were used to classify the characteristic flame modes according to the variation of the fuel-air velocity ratio, into jet-like flame, central-jet-dominated flame, and recirculation zone flame. Stability curves were drawn to find the blowout regimes and to show the improvement in flame stability with increasing lip thickness of the fuel tube, which acts as a bluff-body. These curves collapse to a single line when the blowout curves are normalized by the size of the bluff-body. The variation of flame length with the increase in air flow rate was also investigated. In the subsonic coflow condition, the flame length decreased significantly, but in the supersonic coflow condition, the flame length increased slowly and finally reached a near-constant value. This phenomenon is attributed to the air-entrainment of subsonic flow and the compressibility effect of supersonic flow. The closed-tip recirculation zone flames in supersonic coflow had a reacting core in the partially premixed zone, where the fuel jet lost its momentum due to the high-pressure zone and followed the recirculation zone; this behavior resulted in the long characteristic time for the fuel-air mixing.

• 한국추진공학회지
• /
• 제20권1호
• /
• pp.1-7
• /
• 2016

공동 유동에 대한 연구는 유동이 균일하게 유입되는 수평면상에 설치된 공동에 대한 연구가 대부분이나, 곡면 벽상에 설치한 공동 유동에 관한 연구에 대해서는 거의 수행되지 않았다. 본 연구에서는 곡면 벽상에 설치한 공동 유동의 특성을 조사하기 위해 수치계산을 수행하였으며, 곡면의 형상, 곡면의 곡률 반경 그리고 유동의 마하수를 변화시켜 고아음속 유동에서의 공동 유동 특성을 조사하였다. 그 결과 공동 바닥의 압력은 L/R이 증가함에 따라 증가하였으며, 유동의 마하수가 높을수록 그 효과가 증가하였다. 공동 저항은 수평면 벽보다 곡면 벽에서 더 높은 값을 가졌다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2007년도 추계학술대회 논문집
• /
• pp.156-160
• /
• 2007

Ejector system is a device to transport a low-pressure secondary flow by using a high-pressure primary flow. Ejector system is, in general, composed of a primary nozzle, a mixing section, a casing part for suction of secondary flow and a diffuser. It can induce the secondary flow or affect the secondary chamber pressure by both shear stress and pressure drop which are generated in the primary jet boundary. Ejector system is simple in construction and has no moving parts, so it can not only compress and transport a massive capacity of fluid without trouble, but also has little need for maintenance. Ejectors are widely used in a range of applications such as a turbine-based combined-cycle propulsion system and a high altitude test facility for rocket engine, pressure recovery system, desalination plant and ejector ramjet etc. The primary interest of this study is to set up an applicable model and operating conditions for an ejector in the condition of sonic and subsonic, which can be extended to the hydrogen fuel cell vehicle. Experimental and theoretical investigation on the sonic and subsonic ejectors with a converging-diverging diffuser was carried out. Optimization technique and numerical simulation was adopted for an optimal geometry design and satisfying the required performance at design point of ejector for hydrogen recirculation. Also, some sonic and subsonic ejectors with the function of changing nozzle position were manufactured precisely and tested for the comparison with the calculation results.

• 한국항공우주학회지
• /
• 제37권2호
• /
• pp.166-174
• /
• 2009

본 연구에서는 횡단류 아음속유동장에서 연료가 여러 분사각도를 가지고 수직 분무시 나타나는 액주영역의 궤적과 분열지점에 관한 연구를 수행하였다. 직접 사진촬영 방법과 평면레이저유도형광(PLLIF) 기법으로 정방향 분사각도의 분무에서 액주영역의 궤적식과 분열지점까지의 거리에 대한 경험식을 도출하여 기존 연구결과와 비교 분석하고 대향분사의 액주 궤적식과 분열지점까지의 거리에 대한 경험식을 도출하였다. 실험을 통하여 액주영역의 궤적과 분열지점까지의 거리는 분사차압, 공기의 유속, 인젝터 지름 크기, 분사각도에 의하여 결정됨을 확인하였다.

• 한국항공우주학회지
• /
• 제47권12호
• /
• pp.831-840
• /
• 2019

플러시 대기자료 측정장치는 비행체 표면에서 측정되는 압력 데이터를 이용하여 대기자료를 예측한다. FADS는 돌출된 프로브가 없으므로 고성능 항공기, 스텔스 비행체 및 극초음속 비행체에 적합하다. 본 논문에서는 구-원추 형상을 갖는 비행체에 대해서 아음속부터 초음속 비행까지 대기자료를 예측할 수 있는 FADS의 교정 절차와 계산 알고리즘을 제시한다. 표면 압력 데이터 측정을 위해 노즈부 표면에 5개 플러시 압력공들을 마련하였다. 유동각 예측과 압력 관련 변수의 예측을 분리하는 개념이며, 아음속 유동의 포텐셜 유동해와 극초음속 유동의 수정 뉴톤식을 결합한 압력모델을 사용한다. 교정 압력 데이터는 Euler 방정식을 푸는 전산유체역학 코드를 만들어서 마흐수 0.5 ~ 3.0의 범위에서 구축하였다. 비행 마흐 수 0.6~3.0, 받음각과 옆미끄럼각은 각각 -10° ~ +10°의 범위에서 여러 비행조건에 대해서 테스트를 수행하였다. 예측된 대기자료는 받음각, 옆미끄럼각, 마흐수, 자유류 정압이며 참고 데이터와 비교하여 정확도를 분석하였다.