• Journal of Welding and Joining
• /
• 제25권2호
• /
• pp.49-54
• /
• 2007

Since the wall thickness can be up to 6" or greater, welds must be made in many layers, each layer containing several passes. However, the welding time for the conventional welding processes such as SAW(Submerged Arc Welding) and FCAW(Flux Cored Arc Welding) can be required many hours. The aim of this paper is to develop a high speed welding system with multi-torch and laser vision sensor for increasing the production speed on the line and to remove the need for the operator so that the system can run automatically for the complete multi-torch multi-layer weld. It was shown that the developed laser vision sensor and analysis of arc blow for multi-torch were effective for multi-pass seam tracking and stable arc. A new automated multi-torch welding systems for thick wall applications has been proved in several production lines.

• International Journal of Korean Welding Society
• /
• 제5권1호
• /
• pp.10-14
• /
• 2005

An element of Pure Weld Metal(PWM) is important factor to understand the Flux's conduct in Submerged Arc Welding(SAW). To get the element of PWM, pile-up welding over than 10 layers have been used in the past. But, it took a long time to analyze the elements of PWM in this method. Therefore, in this study, instead of pile-up welding over than 10 layers, one pass bead welding is used to predict an element of PWM using mathematical formula which got to be derived. As a results that applied the formula, there was no differences between theoretical and experimental value except the element Mn and Si.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.320-323
• /
• 2002

This paper presents a new generation of system for pressure vessel and shipbuilding. Typical pressure vessel and ship building weld joint preparations are either traditional V, butt, fillet grooves or have narrow or semi narrow gap profiles. The fillet and U groove are prevalently used in heavy industries and shipbuilding to melt and join the parts. Since the wall thickness can be up to 6" or greater, welds must be made in many layers, each layer containing several passes. However, the welding time for the conventional processes such as SAW(Submerged Arc Welding) and FCAW(Flux Cored Arc Welding) can be many hours. Although SAW and FCAW are normally a mechanized process, pressure vessel and ship structures welding up to now have usually been controlled by a full time operator. The operator has typically been responsible for positioning each individual weld run, for setting weld process parameters, for maintaining flux and wire levels, for removing slag and so on. The aim of the system is to develop a high speed welding system with multitorch for increasing the production speed on the line and to remove the need for the operator so that the system can run automatically for the complete multi-torch multi-layer weld. To achieve this, a laser vision sensor, a rotating torch and an image processing algorithm have been made. Also, the multitorch welding system can be applicable for the fine grained steel because of the high welding speed and lower heat input compare to a conventional welding process.

• 한국산학기술학회논문지
• /
• 제22권3호
• /
• pp.88-93
• /
• 2021

선박의 건조과정이나 압력용기의 몸체 부분을 용접할 경우 많이 사용되는 SAW(Submerged Arc Welding)는, 용접 부위에 분말 형태의 용제(Flux)를 일정 두께로 살포하고 그 속에 전극 와이어를 연속적으로 공급하여 용접이 이루어지는 방법으로 용접 시 발생되는 아크열이 외부로 노출되지 않는 특징이 있으며, 잠호용접으로 불리기도 한다. 또한 1,500~3,000A의 전류까지 통전 할 수 있는 고전류 용접이 가능하며 아크효율이 95% 이상, 미세한 금속 산화물 입자인 Welding Fume 발생량이 적고 아크광선이 외부로 노출되지 않아 청정한 작업이 가능하며 용입이 깊고 결함이 잘 발생하지 않아 용접 이음부의 신뢰도가 높다. 본 연구에서는 SM490C-TMC 후판을 서브머지드 아크용접(SAW)을 이용하여 이종 용접한 후 용접부의 기계적 특성을 인장, 경도, 매크로, 자분탐상 검사 결과를 분석하여 다음과 같은 결론을 도출하였다. 굽힘 시험 결과 시료에서 표면의 터짐 현장이 발생하지 않았고 기타 결점의 유무를 확인할 수 없었으며, 이는 용접 이후 소성변형 과정에서도 충분한 인성을 발휘하고 있는 것으로 나타났으며, 1F 용접 방법이 굽힘 성능에 문제가 없는 것으로 판단되었다.

• Journal of Welding and Joining
• /
• 제13권1호
• /
• pp.78-88
• /
• 1995

This paper was performed to study the utility of the SP(small punch) test and the AE(acoustic emission) test in the evaluation of SCC(stress corrosion cracking) susceptibility for parent metal and bond line of HT80 steel-weld joint by SAW(submerged arc welding) with the various pH values. The loading rate used was 3*10$^{-4}$ mm/min and the corrosive environment used was synthetic sea water during the SP test and the AE test. According to the test results, the SCC susceptibility of the parent metal was increased in the order of pH6.0, pH8.2 and pH10.0. On the other hand, the bond line showed almost the same high SCC susceptibility in all pH concentrations. Synthetically, from the results of the SCC susceptibility, the macro- and micro-SEM observation, the microfracture behaviors by AE test and the relationship between SCC susceptibility and displacement at incipient failure, .delta.$_{i.f-AE}$, it can be concluded that the SP test and the AE test are the good test methods to evaluate the SCC susceptibility for parent metal and bond line of the weld joint with the change of environmental factors.

• Journal of Welding and Joining
• /
• 제6권4호
• /
• pp.27-34
• /
• 1988

The objective of this paper is to investigate the effect of residual stress on fatigue crack growth behavior. For this purpose, submerged arc welding was performed on SM50A steel plate and post weld heta treatment (PWHT) was followed. Residual stress distribution on the weld plate was determined by a hole drilling method and a series of .DELTA.P-const. and .DELTA.K-decreasing fatigue test were performed on the three different regions, i.e. weld metal, HAZ and base metla. Following conclusins were achieved. 1. In "as welded" specimens, tensile residual stresses were produced in the center portion of the specimen while compressive residual stresses were produced near the edges. In PWHT specimens, however, most of the residual stresses were disappeared. 2. The fatigue crack growth behavior in low .DELTA.K region was considerably affected by the presence of residual stress in both "as welded" and PWHT specimens. 3. Because of the relaxation of residual stresses in PWHT condition, the values of m increased from 2.62-2.78 (in the "as welded" condition) to 3.57-3.91 (in the "PWHT" condition)3.91 (in the "PWHT" condition)condition)

• Journal of Advanced Marine Engineering and Technology
• /
• 제9권2호
• /
• pp.126-142
• /
• 1985

The plane bending corrosiion fatigue test for the welded metal parats was performed in the air and in the natural sea water with and without applying cathodic protection. The specimens tested were the weld of SM41 steel plates, SM58 steel plates and of SM41 to SM58, which were all prepared by submerged arc welding. The main results obtained from the experiment are summarized as follows: (1) In case with SM41 and SM58 steel plates, lower value of impact strength, higher value of hardness and more noble electrode potential were observed in the welded metal part than in the HAZ and base metal. Also the lowest hardness zone in the HAZ was observed with SM58 which was not found with SM41. In case with weld specimen of SM41 to SM58, the impact strength and the electrode potential of the welded metal part showed again the lowest and most noble value but the hardness value was located between those of SM41 and SM58 base metal. (2) In the fatigue test, the specimens tested in the air and under the cathodic protection were both cracked in a purely mechanical mode, but the specimens tested without cathodic protection were cracked by the combination of mechanical fracture and electro-chemical corrosion. (3) The corrosion fatigue limit of the welded metal parts of the specimen was increased by the cathodic protection. As the protection potential was varied down to -800 mV vs. SCE the fatigue limit was increased to the value tested in the air, and the maximum fatigue limit appeared at the -1, 000 - -1, 200 mV vs. SCE. However, as the protection potential was further decreased below -1, 200 mV vs.SCE, the fatigue limit of weld of SM58 and of SM41-SM58 joining was decreased but the limit was almost constant in the case of weld of SM41. (4) It is suggested that when designing steel ship the corrosion fatigue limit of welded metal parts should be stressed as a designing strength of the structure of steel ship in addition to the conventional basis considering simply tensile strength of steel and safety factor.

• 대한조선학회논문집
• /
• 제44권6호
• /
• pp.598-604
• /
• 2007

The purpose of this study is to establish the predictive method of welding distortion and residual stress for the channel I butt SA (submerged arc) weldment using FEA. In order to do it, the heat input model for the weldment was defined as the combined heat source with the surface heat flux of gaussian distribution and volumetric heat source uniformly distributed within weld groove by comparing the shapes of molten pool and temperature distribution obtained by FEA with those of experiments. The arc efficiency of SA welding for two-dimensional FE analysis was evaluated as 0.85. The welding distortion and residual stress of the weldment obtained by FEA and heat input model proposed have a good agreement with those obtained by experiment. Based on the results, it was suggested that the proper heat input model should be required to evaluate the welding distortion for weldment.

• Journal of Welding and Joining
• /
• 제4권3호
• /
• pp.43-49
• /
• 1986

Weldability of the TMCP steel manufactured by controlled rolling followed by accelerated cooling process was investigated. For comparison, two other steel plates produced by different manufacturing processes were selected; normalized and controlled rolled. Tandem submerged arc welding with both side one run technique was carried out. The results of this study can be summarized as follows; TMCP steel having the lowest carbon equivalent shows the best combination of mechanical properties, not only in the base metal but also in the heat affected zone. In the HAZ, the accelerated colling effect imarted on the trengthis releved by the weld thermal cycles, and thus the strength of the welded joint decrease substantially accompanied with the fracture in the HAZ. On the other hand, not only the softening but the fine microstructure can preserve the high toughness of TMCP steel in the HAZ.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 1999년도 특별강연 및 추계학술발표대회 개요집
• /
• pp.43-46
• /
• 1999

It has been suggested that the motivation for automation of welding processes ncludes the replacement and extension of the functions of human operators. Among these types of the welding automation, SAW(Submerged Arc Welding) was prevalently used, because it is highly suited to a wide range of application, especially for the high speed welding. A Significant portion of the total manufacturing time for a pipe fabrication process is spent on the welding following primary machining and fit-up processes. To achieve the reliable weld bead appearance, the automatic seam tracking and adaptive control to fill the groove are urgently needed. This paper proposed the mechanical functions of multi-torches welding system, flux supply and recovery system in conjunction with the complex air pulsing method and various types of methodologies. It was shown that the multi-torches welding system revealed the high welding qualities for the circular and rectangular pipes. In conclusion, the multi-torches welding system developed will contribute the advanced welding technology, welding automation and increment of the market in these areas.