• 한국주조공학회지
• /
• 제15권5호
• /
• pp.514-522
• /
• 1995

The microstructural evolution with isothermal stirring during semi-solid state processing of hypoeutectic Al-6.2wt%Si alloy was studied. Substructure of the individual primary solid particle in the slurry was investigated through transmission electron microscopy(TEM). Formation of subgrain boundaries on the rheocast Al-6.2wt%Si alloy is observed and the misorientation between the grains is shown typically under 2 degrees by analyzing selected area diffraction (SAD) and convergent beam electron diffraction (CBED) patterns. The existence of high angle grain boundaries are also observed in the alloy. Based upon these observations, mechanisms for the primary particles fragmentation are considered. With isothermal stirring, the dislocation density increases, and the evolution of dislocation cell structure takes place, which is interpreted as a process of achieving uniform deformation by dynamic recovery under applied shear stress.

• 대한금속재료학회지
• /
• 제49권9호
• /
• pp.699-707
• /
• 2011

P122 steel, with a composition of Fe-10.57%Cr-1.79%W-0.96Cu-0.59Mn was arc-welded and oxidized between $600^{\circ}C$ and $800^{\circ}C$ in air for up to 6 months. The oxidation rates increased in the order of the base metal, weld metal, and heat-affected zone (HAZ), depending on the microstructure. The scale morphologies of the base metal, weld metal, and HAZ were similar because it was determined mainly by the alloy chemistry. The scale consisted primarily of a thin $Fe_2O_3$ layer at $600^{\circ}C$ and $700^{\circ}C$ and an outer $Fe_2O_3$ layer and an inner ($Fe_2O_3$, $FeCr_2O_4$)-mixed layer at $800^{\circ}C$. The microstructural changes resulting from heating between $600^{\circ}C$ and $800^{\circ}C$ coarsened the carbide precipitates, secondary Laves phases, and subgrain boundaries in the matrix, resulting in softening of the base metal, weld metal, and HAZ.

• 한국자기학회지
• /
• 제5권5호
• /
• pp.716-719
• /
• 1995

Pd/(Pt/Co/Pt) modulated multilayer films have been deposited on various substrates with Pd/Pt buffer layers. Films grown at different temperatures have very distinct magnetic properties and surface microstructures. Atomic force(AFM) and scanning tunneling (STM) microscopies studies of these films reveal that films deposited at room temperature have small grain structures with an average grain size of about $140\;{\AA}$. However, much larger grains of about $1200\;{\AA}$ in size are observed in the films grown on buffer layers which were deposited at $500^{\circ}C$. These large grains are found to actually consist of smaller grains of about $170{\AA}$ in diameter. SQUID magnetic and Kerr hysteresis loop measurements indicate that multilayer films with large grains exhibit high magnetic coercivities of around 5 kOe. A subgrain growth model is proposed to understand the observed grain structures in the multilayers.

• 암석학회지
• /
• 제22권4호
• /
• pp.263-272
• /
• 2013

우리는 서부 경기육괴의 연변부에 위치한 덕적도에서 야외 지질조사와 암석기재학적 연구를 실시하여, 덕적도에 산출하는 암상을 (1) 흑운모 화강암, (2) 반상 화강암, (3) 압쇄 규암-편암, 그리고 (4) 저변성퇴적암류로 분류하였다. 흑운모 화강암은 섬의 대부분을 차지하고 있으며, 다른 암상들을 관입하고 있다. 덕적도의 동쪽 연변부를 따라 압쇄화된 반상화강암이 소규모로 산출한다. 섬의 북쪽에는 변성퇴적암이 산출하는데, 동쪽 해안가로 압쇄 규암과 편암이 호층구조를 이루고 서쪽으로는 상대적으로 변형의 강도가 약한 저변성퇴적암이 산출한다. 압쇄 규암-편암에서는 강한 파동소광과 아결정화된 석영과 함께 다량의 백운모와 소량의 녹니석 및 흑운모를 관찰할 수 있다. 이러한 광물조합은 변성도가 녹색편암상 또는 흑운모 분대에 해당함을 지시한다. 저변성퇴적암류에는 변성역암, 변성사암, 변성이암, 흑색점판암 등의 다양한 암상이 존재한다. 덕적도는 동쪽 해안으로 갈수록 암석의 종류에 관계없이 파쇄의 정도가 심해지고 일부에서는 석영이 연성전단작용에 의해 유동띠의 형태를 가지는 전단대가 발달한다.

• 열처리공학회지
• /
• 제18권1호
• /
• pp.3-11
• /
• 2005

Using various thermo-mechanical schedules characterized by varying reheating temperature, deformation temperature and strain, the austenite recrystallization and ferrite refinement of a Nb bearing low carbon steel(0.15C-0.25Si-1.11Mn-0.04Nb) were investigated. For single pass heavy deformations at $800^{\circ}C$, the 40% deformed austenite was not recrystallized while the 80% deformed one was fully recrystallized. Ferrite grains formed in the 80% deformed specimen was not very small compared with those in the 40% deformed specimen, which implied the recrystallized austenite was not more beneficial to ferrite refinement than the non-recrystallized one. In case of deformation in low temperature austenite region, a multi-pass deformation made finer ferrites than a single-pass deformation, as the total reduction was the same, due to more ferrite nucleation sites in the non-recrystallization of austenite for multi-pass deformation. When specimen was deformed at $775^{\circ}C$ that was $10^{\circ}C$ higher than $Ar_3$, the ferrite of about $1{\mu}m$ was formed through deformation induced ferrite transformation(DIFT), and the amount of ferrite was increased with increasing reduction. Dislocation density was very high and no carbides were observed in DIFT ferrites, presumably due to supersaturated carbon solution. By deformation in two phase(50% austenite+50% ferrite) region the very refined ferrite grains of less than $1{\mu}m$ were formed certainly by recovery and recrystallization of deformed ferrites and, a large portion of ferrites were divided by subgrain boundaries with misorientation angles smaller than 10 degrees.

• 한국재료학회지
• /
• 제9권11호
• /
• pp.1123-1128
• /
• 1999

Zr합금의 재결정에 미치는 Sn 영향을 조사하기 위해서 Zr-xSn (x=0.5, 0.8, 1.5, 2.0wt.%) 합금을 판재로 제조하여 $300^{\circ}C-800^{\circ}C$에서 1시간 동안 열처리하였다. 열처리 온도에 따른 Zr합금의 경도, 미세조직 및 석출물 특성을 미소경도계, 광학 현미경 및 투과 전자 현미경을 이용하여 조사하였다. 냉간가공된 Zr-xSn 합금은 회복, 재결정, 결정립 성장의 전형적인 거동을 나타냈으며, 냉간가공재의 재결정은 $500^{\circ}C$에서 $700^{\circ}C$ 범위에서 완료되었다. Sn량이 증가함에 따라서 합금의 재결정온도는 증가하였고 재결정후의 결정립 크기는 감소하였다. 경도 변화는 미세조직 변화와 잘 일치하는 경향을 보였다. 실험 결과로부터 냉간 가공된 Zr합금의 재결정은 아결정립의 합체 및 성장기구에 의해서 일어나는 것으로 평가되었다.

• 한국주조공학회지
• /
• 제17권4호
• /
• pp.356-364
• /
• 1997

In order to study effects of Cu and Be on the microstructure and tensile properties of rapidly solidified Al-Mg alloys, Al-Mg-Cu-Be alloys have been rapidly solidified by inert gas atomization process. Microstructure of rapidly solidified Al-Mg-Cu-Be powders exhibited refinement and good dispersion of Be particles as increasing of solidification rate. Solidification rate of atomized powders was estimated to be about $5{\times}10^{3{\circ}}C/s$. Inert gas atomized Al-Mg-Cu-Be powders were hot-processed by vacuum hot pressing at $450^{\circ}C$ under 100 MPa and hot extruded with reduction ratio in area of 25: 1 at $450^{\circ}C$. The extruded Al-Mg-Cu-Be powders consisted of recrystallized fine Al grains and homogeneously dispersed fine Be particles, and exhibited improved tensile properties with increase in Cu content. $Al_2CuMg$ compounds precipitated in grain and grain boundaries of Al-Mg-Cu-Be alloys with aging heat treatment after solution treatment. Hardness and tensile properties were improved by increasing Cu content and Be addition. Compared with extruded Al-Mg-Cu powders, the extruded Al-Mg-Cu-Be powders exhibited finer recrystallized grains and improved tensile properties by dispersion hardening of Be and subgrain boundaries pinned by fine Be particles. After aging treatment, hardness and tensile properties were improved due to restricted precipitation by increasing of dislocation density around Be particles in matrix.

• Electronic Materials Letters
• /
• 제14권6호
• /
• pp.678-688
• /
• 2018

The repeated-bending properties of Sn-0.7Cu, Sn-0.3Ag-0.7Cu (SAC0307), and Sn-3.0Ag-0.5Cu (SAC305) solders mounted on flexible substrates were studied using highly accelerated stress testing (HAST), followed by repeated-bending testing. In the Sn-0.7Cu joints, the $Cu_6Sn_5$ intermetallic compound (IMC) coarsened as the HAST time increased. For the SAC0307 and SAC305 joints, the $Ag_3Sn$ and $Cu_6Sn_5$ IMCs coarsened mainly along the grain boundary as the HAST time increased. The Sn-0.7Cu solder had a high contact angle, compared to the SAC0307 and SAC305 solders; consequently, the SAC0307 and SAC305 solder joints displayed smoother fillet shapes than the Sn-0.7Cu solder joint. The repeated-bending for the Sn-0.7Cu solder produced the crack initiated from the interface between the Cu lead wire and the solder, and that for the SAC solders indicated the cracks initiated at the surface, but away from the interface between the Cu lead wire and the solder. Furthermore, the oxide layer was thickest for Sn-0.7Cu and thinnest for SAC305, regardless of the HAST time. For the SAC solders, the crack initiation rate increased as the oxide layer thickened and roughened. $Cu_6Sn_5$ precipitated and grew along the grain and subgrain boundaries as the HAST time increased, embrittling the grain boundary at the crack propagation site.

• 대한금속재료학회지
• /
• 제50권12호
• /
• pp.931-937
• /
• 2012

The microstructure of Cu-15 wt%Ag composites fabricated by equal channel angular pressing (ECAP) with intermediate heat treatment at $320^{\circ}C$ was investigated by transmission electron microscopy (TEM) observations. Ag precipitates with a thickness of 20-40 nm were observed in the eutectic region of the Cu-15 wt%Ag composite solution treated at $700^{\circ}C$ before ECAP. The Cu matrix and Ag precipitates had a cube on cube orientation relationship. ECAPed composites exhibited ultrafine-grained microstructures with the shape and distribution dependent on the processing routes. For route A in which the sample was pressed without rotation between each pass, the Cu and Ag grains were elongated along the shear direction and many micro-twins were observed in elongated Cu grains as well as in Ag filaments. The steps were observed on coherent twin boundaries in Cu grains. For route Bc in which the sample was rotated by 90 degrees after each pass, a subgrain structure with misorientation of 2-4 degree by fragmentation of the large Cu grains were observed. For route C in which the sample was rotated by 180 degrees after each pass, the microstructure was similar to that of the route A sample. However, the thickness of the elongated grains along the shear direction was wider than that of the route A sample and the twin density was lower than the route A sample. It was found that more microtwins were formed in ECAPed Cu-15 wt%Ag than in the drawn sample. Grain boundaries were observed in relatively thick and long Ag filaments in Cu-15 wt%Ag ECAPed by route C, indicating the multi-crystalline nature of Ag filaments.

• 열처리공학회지
• /
• 제35권6호
• /
• pp.303-313
• /
• 2022

The purpose of this study was to test and analyze the effects of the mechanical properties and structural changes of the austenitized and tempered martensite STS 410 stainless steel containing 11.5~13%Cr and 0.10%C on its temper embrittlement. The STS 410 stainless steel test pieces for each 3 hours at 960℃, 1000℃ and then, tempered them for 2 hours at 300℃, 350℃, 400℃, 450℃, 500℃, 550℃, 600℃, 650℃ and 700℃ known as the intervals vulnerable to temper embrittlement to observe the changes of their structures and mechanical properties. In case autenitizing was insufficient due to lower temperature of thermal treatment for solution, unsolved carbides and ferrites remained in the structure after quenching, which meant that the parts could wear out and corrode to embrittle at the room temperature. Elongation and impact energy changes with Tempering conditions showed minimum results in range of 400~500℃. The decrease in elongation and impact energy at 400~500℃ was the hardening effect of the subgrain due to the precipitation of many M₃C or M₇C₃, M₂₃C₆. And STS 410 stainless steel corrosion tested in 10% NaCl solution at 30℃ after tempering treatment. The degree of corrosion sensitization showed increasing tendency with increase of tempering temperature and Cr carbide precipitation were observed in grain boundary.