• 대한기계학회논문집B
• /
• 제30권9호
• /
• pp.905-912
• /
• 2006

Experiments in low strain rate methane-air counterflow diffusion flames diluted with $CO_2$ have been conducted to investigate the flame extinction behavior and edge flame oscillation in which flame length is less than the burner diameter and thus lateral conductive heat loss in addition to radiative loss could be remarkable at low global strain rates. The critical mole fraction at flame extinction is examined in terms of velocity ratio and global strain rate. It is seen that flame length is closely relevant to lateral heat loss, and this sheets flame extinction and edge flame oscillation considerably. Lateral heat loss causes flame oscillation even at fuel Lewis number less than unity. Edge flame oscillations are categorized into three: a growing-, a harmonic- and a decaying-oscillation mode. Onset conditions of the edge flame oscillation and the relevant modes are examined with global strain rate and $CO_2$ mole fraction in fuel stream. A flame stability map based on the flame oscillation modes is also provided at low strain rate flames.

• 한국자기학회지
• /
• 제18권4호
• /
• pp.127-130
• /
• 2008

본 논문에서는 수 백 나노미터 크기의 자성 소자에서 존재하는 강자기 소용돌이 구조의 운동에 대한 이론을 제시한다. LLG 방정식으로부터 유도된 운동방정식, 즉 Thiele 방정식에 그 이후 밝혀진 이론적 결과들을 도입하여 강자기 소용돌이의 감쇠 단조화 운동방정식을 도출하였다. 이러한 운동방정식으로부터 감쇠 단조화 운동의 고유 진동수와 감쇠 상수를 나타내는 수식을 유도하였으며, 유도된 수식을 micromagnetic 시늉 실험을 통하여 검증하였다.

• Journal of Power Electronics
• /
• 제10권2호
• /
• pp.132-137
• /
• 2010

Interleaving techniques are widely used to reduce input/output ripples and to increase the power capacity of boost converters operating in critical conduction mode. Two types of phase-shift control schemes are studied in this paper, the turn-on time shifting method and the turn-off time shifting method. It is found that although the turn-off time shifting method exhibits better performance, it suffers from sub-harmonic oscillations at high input voltages. To solve this problem, an intensive quantitative analysis of the sub-harmonic oscillation phenomenon is made in this paper. Based upon that, a novel modified turn off time shifting control scheme for interleaved boost converters operating in critical conduction mode is proposed. An important advantage of this scheme is that both the master phase and the slave phase can operate stably in critical conduction mode without any oscillations in the full input voltage range. This method is implemented with a FPGA based digital PWM control platform, and tests were carried out on a two-phase interleaved boost PFC converter prototype. Experimental results demonstrated the feasibility and performance of the proposed phase-shift control scheme.

• 산업기술연구
• /
• 제32권A호
• /
• pp.115-118
• /
• 2012

Recently, there are a lot of papers in order to replace the electrolytic capacitor into the film capacitor in output of PFC(Power Factor Correction). However, the film capacitor, which has capacitance of low values, causes a large ripple voltage in output of PFC. The LED drivers are connected series in the output of PFC and affected by the magnitude of voltage ripple. In this paper, we have compared the fixed frequency method with the variable frequency for the constant-current control and propose the control method to avoid the sub-harmonic oscillation in the variable input voltage. An 80W PFC, using film capacitors instead of electrolytic capacitors, and LED driver has been built and compared the fixed frequency control method with the variable frequency control method.

• 전력전자학회논문지
• /
• 제24권2호
• /
• pp.134-137
• /
• 2019

A wide-bandwidth current controller is required for fast charging/discharging of super capacitor applications. Peak current mode is generally used to accomplish fast charging/discharging because this mode has fast response characteristics. However, the peak current mode control must have a slope compensation function to restrain sub-harmonics oscillation. The slope must be changed accordingly if the controlled output voltage is varied. However, changing the slope for every changed output voltage is not easy. The other solution, selecting the slope as the maximum value, causes a slow response problem to occur. Therefore, we propose a hybrid mode controller that uses a peak current and a newly specified valley current. Through the proposed hybrid mode control, the sub-harmonic oscillation does not occur when the duty is larger than 0.5 because of the fast response.

• 대한전자공학회논문지TC
• /
• 제44권7호통권361호
• /
• pp.7-11
• /
• 2007

본 논문에서는 다중밴드 직접 변환 수신기를 위한 Octa-Phase 전압 제어 발진기를 제안하였다. Octa-Phase 신호와 저 위상잡음을 얻기 위해 4개의 LC VCO를 직렬 커플링 트랜지스터를 이용해 연결하였다. 멀티 밴드 특성을 얻기 위해 밴드 튜닝 회로가 제안되었다. MOS 스위치가 켜짐/꺼짐에 따라서 주파수 범위는 변화한다. 2개의 veractor를 사용해 VCO의 발진 주파수의 공정상의 오차를 최소화하였다. 본 논문에서는 0.18 um CMOS 공정을 이용해 발진기를 설계하였다. 측정 결과 1.8V 공급전압에 12mA의 전류를 소모하였고, $885MHz^{\sim}1342MHz$ 사이의 범위에서 동작하여 3개의 표준(CDMA 20001x, WCDMA, WiBro)에서의 sub-harmonic 혼합기를 구동시킬 수 있는 동작 범위를 만족시킨다. 측정된 위상잡음은 각각 CDMA 2000 1x 대역에서는 -105dBc@100kHz, WCDMA 대역에서는 -115dBc@1MHz, WiBro 대역에서는 -130dBc@10MHz으로 나타났다.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2017년도 추계학술대회
• /
• pp.3-4
• /
• 2017

컨버터 제어를 위한 피크 전류 모드는 기존의 전류 모드 제어 기법에 비해 빠른 응답과 간단한 구조로 인해 많은 컨버터 애플리케이션에서 사용된다. 그러나 듀티가 0.5를 초과하면, 서브 하모닉 발진이 전류에서 발생한다. 이러한 현상을 방지하기 위해 제어기를 안정적으로 동작 할 수 있도록 보상 기울기를 추가 한다. 그러나 기울기 보상의 방법은 구조를 복잡하게 만들고 출력 전압이 가변적 일 때 때때로 기울기를 변화시켜야 하는 문제가 있다. 따라서 본 논문에서는 기울기 보상 없이 새로운 하이브리드 모드 전류 제어 방법을 제안한다. 밸리 전류 모드에서 트레일 링 에지 변조를 사용하는 제안 된 방법에서, 서브 하모닉 발진 문제는 쉽게 해결 될 수 있다. 제안 된 제어기는 Psim 시뮬레이션에 의해 검증된다.

• 한국소음진동공학회논문집
• /
• 제15권6호
• /
• pp.706-711
• /
• 2005

Torsional oscillations of a system incorporating a Hooke's joint are investigated by studying a simple similar nonlinear 2-degree-of-freedom model, which has linear and quadratic nonlinear parametric excitations. The simple system is identified to have the possibilities of primary, sub harmonic and combination resonances. The case of simultaneous primary and combination resonances is selected for perturbation analysis to have the reduced amplitude-equations of motion. The same procedure is applied to the system incorporating a Hooke's joint.

• Journal of Power Electronics
• /
• 제16권1호
• /
• pp.227-237
• /
• 2016

A novel digital current control strategy for digitally controlled DC-DC switching converters, referred to as Adjacent Cycle Sampling (ACS), is proposed in this paper. For the ACS current control strategy, the available time interval from sampling the current to updating the duty ratio, is approximately one switching cycle. In addition, it is independent of the duty ratio. As a result, the contradiction between the processing speed of the hardware and the transient response speed can be effectively relaxed by using the ACS current control strategy. For digitally controlled buck DC-DC switching converters with trailing-edge modulation, digital current control algorithms with the ACS control strategy are derived for three different control objectives. These objectives are the valley, average, and peak inductor currents. In addition, the sub-harmonic oscillations of the above current control algorithms are analyzed and eliminated by using the digital slope compensation (DSC) method. Experimental results based on a FPGA are given, which verify the theoretical analysis results very well. It can be concluded that the ACS control has a faster transient response speed than the time delay control, and that its requirements for hardware processing speed can be reduced when compared with the deadbeat control. Therefore, it promises to be one of the key technologies for high-frequency DC-DC switching converters.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제8권4호
• /
• pp.330-343
• /
• 2016

This paper presents results of an experimental investigation of vortex-induced vibration (VIV) of a flexibly mounted and rigid cylinder with two-degrees-of-freedom with respect to varying ratio of in-line natural frequency to cross-flow natural frequency, $f^*$, at a fixed low mass ratio. Combined in-line and cross-flow motion was observed in a sub-critical Reynolds number range. Three-dimensional displacement meter and tension meter were used to measure dynamic responses of the model. To validate the results and the experiment system, x and y response amplitudes and ratio of oscillation frequency to cross-flow natural frequency were compared with other experimental results. It has been found that the higher harmonics, such as third and more vibration components, can occur on a certain part of steel catenary riser under a condition of dual resonance mode. In the present work, however, due to the limitation of a size of circulating water channel, the whole test of a whole configuration of the riser at an adequate scale for VIV phenomenon was not able to be conducted. Instead, we have modeled a rigid cylinder and assumed that the cylinder is a part of steel catenary riser where the higher harmonic motions could occur. Through the experiment, we have found that even though the cylinder was assumed to be rigid, the occurrence of the higher harmonic motions was observed in a small reduced velocity ($V_r$) range, where the influence of the in-line response is relatively large. The transition of the vortex shedding mode from one to another was examined by using time history of x and y directional displacement over all experimental cases. We also observed the influence of in-line restoring force power spectral density with $f^*$.