• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.5
• /
• pp.722-730
• /
• 2001

The local heat transfer of an axisymmetric submerged air jet impinging on a heated flat plate is investigated experimentally with the variation of mesh-screen solidity. The screen installed in front of the nozzle exit modifies the flow structure and local heat transfer characteristics. The mean velocity and turbulence intensity profiles of streamwise velocity component are measured using a hot-wire anemometry. The temperature distribution on the heated flat surface is measured with thermocouples. The smoke-wire flow visualization technique was employed to understand the near-field flow structure qualitatively for different mesh screens. Large-scale toroidal vortices and high turbulence intensity enhance the heat transfer rate in the stagnation region. For a higher solidity, turbulence intensity become higher which increases the local heat transfer at small nozzle-to-plate spacings such as L/D<6. The local and average Nusselt numbers of impinging jet from the $\sigma$(sub)s=0.83 screen at L/D=2 are about 5.6∼7.5% and 7.1% larger than those for the case of no screen, respectively. For the nozzle-to-plate spacings larger than 6, however, the turbulence intensities for all tested screens approach to an asymptotic curve and the mean velocity along the jet centerline decreases monotonically. As the nozzle-to-plat spacing increases for high solidity screens, the heat transfer rate decreases due to the reduction in turbulence intensity and jet momentum.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.10
• /
• pp.1327-1336
• /
• 2001

The structural modes driven by the low wave-number components of smooth elastic wall pressure provide a relatively weak coupling between the flow and the wall motion. If the elastic thin plate has any resonant mode whose wave-number of resonance coincides with $\omega$/U$\sub$c/, the power will be transmitted to those modes of vibration by the flows. We examine the problem in which the elastic thin plate is subject to pressure fluctuations under turbulent boundary layer. Measurements are presented of the frequency spectra of the near- and far-field pressures and radiated sound contributed by the various wave modes of the thin elastic plate. Dispersion equation for wave motions of elastic plate is used to investigate the effect of bending waves of relatively low wave number on radiated sound. The low wave-number motion of elastic plate is observed to have much less influence on the low-frequency energy of wall pressure fluctuations than that of the rediated sound. High amplitude events of the wall pressure are observed to weakly couple with high-frequency energy of radiated sound for case of low tension applied to the plate. The sound source localization is applied to the measurement of radiated sound by using acoustic mirror system.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.33 no.5
• /
• pp.521-528
• /
• 2009

One of reliability measurements of vehicle is estimated by driving mileage but the reliability of component, such as an hydraulic clutch system, is defined from the number of successful operational cycle. Relationship between these reliability measurement variables(mileage and cycle) should be examined first of all in the reliability estimation of components. Relationship between mileage and cycles is commonly known as linear function. However, the gradient depends on the operational environmental condition. Therefore, estimation of mission profile variable should be done with correlation analysis at the same time. In this paper, we derive mission profile variable of an hydraulic clutch system by field vehicle test and suggest the determination process of durability test parameters of CMC(Clutch Master Cylinder) with mission profile variable.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.21 no.4
• /
• pp.195-211
• /
• 2019

In this paper, Capstone Design Education Program Learning Model was developed and recommended in order to foster convergent talents armed with practical competences and real cooperative capabilities. In this era of convergence and creativity, the fashion world needs human resources with cooperative skills and true professional abilities. A case analysis, an in-depth interview, and 1,2 test method were used for data acquisition and analysis. The summary of this study is described below. First, this program needs to complement the NCS fashion design learning module. Second, material changes to creativity and practical competencies - knowledge, skills, and attitudes - of the students are assessed after applying Capstone Design to the NCS fashion design learning model. Third, the process of converging fashion curriculum with IT and electronic technology, developing a fashion design learning program, and applying the Capstone Design was tested to prove the effectiveness of convergent fashion design education. Among the changes observed between the trial and control groups, it was confirmed that sub-factors of creative personality, i.e. self-assurance and openness, were increased along with knowledge, core competences including communication capability, and self-directed learning capability. The greatest improvement on the technological side was observed in IT literacy while ability to respond to changes was also increased. Besides, effects were demonstrated in behavioral factors such as initiative, spirit of challenge, experience, and openness. Lastly, the Capstone Design Education Program Learning Model was proposed in order to foster convergent talents in the fashion world.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.32 no.3
• /
• pp.310-316
• /
• 1987

A field experiment was conducted to find out the effects of liming(soil pH) and sources of N on growing characters and yield of burley tobacco. Treatments consisted of liming(nonliming, liming to soil pH5.5 and 6.5) as the main plot and N sources(compound fertilizer of containing 3.9% NH$_4$-N and 6.1% NH$_2$-N, NaNO$_3$,(NH$_2$)$_2$CO and (NH$_4$)$_2$SO$_4$as the sub-plot. The growth of vegetative growing stage of limed plots were delayed(to compare the nonlimed plot) by influence of alkali. When the source on N was NaNO$_3$ the growth of vegetative growing stage was unfavorable and the yellowing of lower leaves of maturing stage was rapid. The yield and value of cured leaf was increased by increasing the rate of Ca(OH)$_2$, but there was no significant differences among the source of N. The yield response to liming was greater when the source of N was (NH$_4$)$_2$SO$_4$ than that of any other plots.

• Economic and Environmental Geology
• /
• v.41 no.1
• /
• pp.133-144
• /
• 2008

The outputs from the fundamental research program of the Korea Institute of Geoscience and Mineral Resources (KIGAM) were analyzed using the research budget and manpower as input variables. The analysis was performed based on the research outputs of the past 3 years (FY2004 to 2006). More articles and patents came out in applied and development research areas among the geosciences fields. The statistical analysis indicates that each sub-field has different characteristics in research outputs. Research articles, patents, and research budget increase as the manpower increase. But research articles and patents do not always show positive relations to research budget.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.10
• /
• pp.10-20
• /
• 2003

In this study, the effective properties were numerically calculated for laminated plain weave textile composites with arbitrary s tacking orientation angles. A single-field macroelement with modified sub-domain integration was used in the analysis to reduce computer resource requirement while efficiently accounting for the internal microstructure. A sample calculation procedure based on the Monte Carlo method was employed to consider the random shift between the layers. Results showed that a significant deviation occurred when the orientation angles were near 0 deg for extensional modulus and Poisson's ratio and 45 deg for the shear modulus. It was also found that the average properties calculated by the 2-layer numerical specimen had large differences compared to the CLT results, which indicated that a caution must be needed when designig of thin plain weave composite structures.

• Microbiology and Biotechnology Letters
• /
• v.32 no.4
• /
• pp.312-316
• /
• 2004

In oder to select the powerful rhizophere-dorminatable biocontrol agent, we had isolated an indigenous antagonistic bacterium which produced antibiotic and siderophore from a disease suppressive local field soil of Gyungsan, Korea. And we could select the Pseudomosp. 4059 which can strongly antagonize against Fusarium oxysporum and Phytophthora capsici by two kinds of antifungal mechanism that can be caused by the antibiotic of Phenazin, a siderophore and a auxin like subThe selected strain was identified as Pseudomonas fluorescens (biotype A) 4059 by biochemical tests, API $\textregistered$ test, MicroLog TM system and 16S rDNA analysis. The selected antagonistic microorganism, Pseudomosp. 4059 had an antifungal mechanism of antifungal antibiotic and sidrophore. And we were confirmed the antagonistic activity of P fluorescens 4059 with in vitro antifungal test against Phytophthora capsici and in vivo by red-pepper.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.480-480
• /
• 2000

In this paper, we proposed a fuzzy-neuro controller to control the speed of wound rotor induction motor with slip energy recovery. The speed is limited at some range of sub-synchronous speed of the rotating magnetic field. Control speed by adjusting resistance value in the rotor circuit that occurs the efficiency of power are reduced, because of the slip energy is lost when it passes through the rotor resistance. The control system is designed to maintain efficiency of motor. Recently, the emergence of artificial neural networks has made it conductive to integrate fuzzy controllers and neural models for the development of fuzzy control systems, Fuzzy-neuro controller has been designed by integrating two neural network models with a basic fuzzy logic controller. Using the back propagation algorithm, the first neural network is trained as a plant emulator and the second neural network is used as a compensator for the basic fuzzy controller to improve its performance on-line. The function of the neural network plant emulator is to provide the correct error signal at the output of the neural fuzzy compensator without the need for any mathematical modeling of the plant. The difficulty of fine-tuning the scale factors and formulating the correct control rules in a basic fuzzy controller may be reduced using the proposed scheme. The scheme is applied to the control speed of a wound rotor induction motor process. The control system is designed to maintain efficiency of motor and compensate power factor of system. That is: the proposed controller gives the controlled system by keeping the speed constant and the good transient response without overshoot can be obtained.

• Journal of Astronomy and Space Sciences
• /
• v.35 no.3
• /
• pp.195-200
• /
• 2018

The present paper describes the design of a Solid State Telescope (SST) on board the Korea Astronomy and Space Science Institute satellite-1 (KASISat-1) consisting of four [TBD] nanosatellites. The SST will measure these radiation belt electrons from a low-Earth polar orbit satellite to study mechanisms related to the spatial resolution of electron precipitation, such as electron microbursts, and those related to the measurement of energy dispersion with a high temporal resolution in the sub-auroral regions. We performed a simulation to determine the sensor design of the SST using GEometry ANd Tracking 4 (GEANT4) simulations and the Bethe formula. The simulation was performed in the range of 100 ~ 400 keV considering that the electron, which is to be detected in the space environment. The SST is based on a silicon barrier detector and consists of two telescopes mounted on a satellite to observe the electrons moving along the geomagnetic field (pitch angle $0^{\circ}$) and the quasi-trapped electrons (pitch angle $90^{\circ}$) during observations. We determined the telescope design of the SST in view of previous measurements and the geometrical factor in the cylindrical geometry of Sullivan (1971). With a high spectral resolution of 16 channels over the 100 keV ~ 400 keV energy range, together with the pitch angle information, the designed SST will answer questions regarding the occurrence of microbursts and the interaction with energetic particles. The KASISat-1 is expected to be launched in the latter half of 2020.