• Journal of Korean Society of Steel Construction
• /
• v.24 no.5
• /
• pp.511-520
• /
• 2012

The double split Tee connection, a type of full strength-partially restrained connection, has adequate flexural strength according to the changes in the thickness of the T-stub flange and the gauge distance of the high-strength bolts. Moreover, the double split Tee connection is designed and constructed with seismic connections that have enough ductility capacity applicable to ordinary moment frame and special moment frame by grade of steel, size of beam and column and geometric connection shape. However, such a domestic research and a proposal of a suitable design formula about the double split Tee connection are insufficient. Thus, many experimental and analytical studies are in need for the domestic application of the double split Tee connection. Therefore, this study aimed to examine and suggest feasibility of a design formula of the double split Tee connection of FEMA.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.47 no.8
• /
• pp.68-73
• /
• 2010

In this paper, a compact Ultra-Wideband band-pass filter with notched band at 5.8GHz by using LC resonator is proposed. The structure of the proposed band-pass filter is very simple, and the DGS(Defected Ground Structure) is used to get the low-pass filter characteristics and the LC resonator is used to get the notched filter. The proposed band-pass filter can be much smaller than a cascaded filter type. The LC resonator is designed with a radial stub and small stub. As a result of measurement, the insertion loss is less than 0.5dB throughout the pass-band of 2.21GHz~10.92GHz, the return loss is more than 16dB and the maximum variation of group delay is 0.29ns and a notched band is 5.2GHz~6.2GHz.

• Steel and Composite Structures
• /
• v.35 no.5
• /
• pp.611-625
• /
• 2020

Experimental investigation and finite element analysis of corroded cold-formed steel (CFS) columns are presented. 11 tensile coupon specimens and 6 stub columns of corroded CFS that had a channel section of C160x60x20 were subjected to monotonic tensile tests and axial compression tests, respectively. The degradation laws of the mechanical properties of the tensile coupon specimens and stub columns were analysed. An appropriate finite element model for the corroded CFS columns was proposed and the influence of local corrosion on the stability performance of the columns was studied by finite element analysis. Finally, the axial capacity of the experimental results was compared with the predictions obtained from the existing design specifications. The results indicated that with an increasing average thickness loss ratio, the ultimate strength, elastic modulus and yield strength decreased for the tensile coupon specimens. Local buckling deformation was not noticeable until the load reached about 90% of the ultimate load for the non-corroded columns, while local buckling deformation was observed when the load was only 40% of the ultimate load for the corroded columns. The maximum reduction of the ultimate load and critical buckling load was 57% and 81.7%, respectively, compared to those values for the non-corroded columns. The ultimate load of the columns with web thickness reduced by 2 mm was 53% lower than that of the non-corroded columns, which indicates that web corrosion most significantly affects the bearing capacity of the columns with localized corrosion. The results predicted using the design specifications of MOHURD were more accurate than those predicted using the design specifications of AISI.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.6 s.97
• /
• pp.594-602
• /
• 2005

In this paper, a new type of 5-pole low pass filter(LPF) having defected ground structure(DGS) and very wide transmission line elements is proposed. The previously presented design method of 3-stage LPF using DGS is generalized to design N-pole LPFs for $N\geq5$. As an example, a 5-pole LPF having DGS is designed and measured. The accurate curve-fitting method to determine the series inductors in the prototype filter, and ultimately the size of DGS is described. The proposed 5-pole LPF has transmission line elements with a very low impedance to realize the required shunt capacitance instead of open stubs. Therefore, open stub. Therefore, open stub, Tee-junction, Cross-junction, and high impedance line are not required for the proposed LPF, while they all have been essential in conventional LPFs.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.6
• /
• pp.583-590
• /
• 2010

In this paper, a novel CRLH-TL unit cell with controllable transmission zeros was proposed. Proposed composite right/left handed transmission line(CRLH-TL) unit cell is implemented in the form of the metal-insulator-metal(MIM) capacitors, the microstrip stub inductors, and the co-planar waveguide(CPW) inductor. And this proposed CRLH-TL generates two transmission zeros in lower/upper passband by the effort of electromagnetic couplings between each MIM capacitors and microstrip stub inductors. Using this proposed CRLH-TL, broad bandpass filter for UWB system was designed and fabricated. The measured results reveal that the two transmission zeros are observed in lower/upper passband and the overall size of the filter, excluding the feed line is about 8 mm$\times$8 mm, less then $\lambda_g$/4 on electric size.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.8
• /
• pp.632-639
• /
• 2018

This paper presents a single antenna radar sensor with a Ku-band radar transceiver IC realized by 130 nm CMOS processes. In this radar receiver, sensitivity time control using a DC offset cancellation feedback loop is employed to achieve a constant SNR, irrespective of distance. In addition, the receiver RF block has gain control to adjust high dynamic range. The RF output power is 9 dBm and the full chain gain of the Rx is 82 dB. To reduce the direct-coupled Tx signal to the Rx in a single antenna radar, a stub-tuned hybrid coupler is adopted instead of a bulky circulator. The maximum measured distance between the horn antenna and a metal plate target is 6 m.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.5
• /
• pp.475-483
• /
• 2013

In this paper, a coupled-fed monopole antenna for LTE/WWAN mobile handset applications is presented. The antenna consists of a monopole, a coupling strip, a feeding pad, a stub, and a shorting strip. The basic resonance of the monopole combines with the resonance formed by the coupling that occurs between the coupling strip and the feeding pad to include LTE700(698~787 MHz), GSM850(824~894 MHz), and GSM900(890~960 MHz) bands. The resonance of the stub combines with the harmonics of the monopole to include GSM1800(1,710~1,880 MHz), GSM1900(1,850~1,990 MHz), and UMTS(1,920~2,170 MHz) bands. Therefore, the proposed antenna is suitable as antenna for hexa-band mobile handset applications, covering LTE700, GSM850, GSM900, GSM1800, GSM1900, and UMTS bands. A stable and omni-directional radiation pattern with reasonable gains is observed within the operating bandwidth.

• Journal of Advanced Navigation Technology
• /
• v.13 no.1
• /
• pp.41-47
• /
• 2009

In this paper, a band pass filter with a rejection band is proposed for UWB(Ultra Wide Band) communication system. First, low pass filter accessed cut off frequency of 10.2 GHz was designed using structure stepped impedance. And high pass filter accessed cut of frequency of 3.2 GHz was designed using parallel short-stub. There was implemented composite connection of designed low pass filter and high pass filter. The relative dielectric constant, the height, the loss tangent of the PCB substrate were ${\varepsilon}_r$=2.2, h=0.508 mm and loss tangent = 0.0009 respectively. The fabricated band pass filter shows a compact size of 3 cm. The fabricated band pass filter was characterized using 37169A VNA(Vector Network Analyzer). And measured result were obtained 7.5 GHz of bandwidth and -10 dB of return loss and -3 dB of insertion loss from pass band. The result of the research can be used for the UWB communications and MIC/MMIC, RFIC system.

• 한국ITS학회:학술대회논문집
• /
• v.2006 no.10
• /
• pp.187-190
• /
• 2006

In this paper, the equivalent circuit of tapped-line that is applied in the feeding of the band-pass filter with high coupling is suggested and the value of an equivalent circuit is mathematically defined. An equivalent circuit of tapped-line is composed by open stub and additional transmission line, and the electrical lengths of stub and line can be obtained by the impedance of resonator and the inverter. The new equivalent circuit of tapped-line can be simply applied of design of band-pass filter and leads to very good agreement compared with theoretical value. The coupled-line band-pass filter using equivalent circuit of tapped-line shows the insertion loss of 1.97 dB and the return loss of 18.5 dB at the center frequency of 5.8 GHz.

• Journal of Korean Society of Steel Construction
• /
• v.24 no.3
• /
• pp.279-287
• /
• 2012

A double split tee connection is used as a connection that is suitable for ordinary moment frames or special moment frames according to the combination of variables of the thickness of the T-stub flange and the gauge distance of the high-strength bolts. In order to demonstrate safe structural behavior, a double split tee connection must meet the requirements for inter-story drift angles and the moment of connection, as defined in the Korea Building Code-Structural. In order to determine whether the these requirements are met, it is necessary to predict rotational stiffness and the ultimate plastic moment of the connection. Therefore, this study primarily aimed to propose an analytical model for predicting the rotational stiffness of a double split tee connection under a static load. Toward this end, a three-dimensional, non-linear finite element analysis was carried out. Then, the applicability of the proposed model was verified after comparing the test results of this study with other studies.