• 한국구조물진단유지관리공학회 논문집
• /
• 제18권1호
• /
• pp.31-39
• /
• 2014

뼈대구조물의 강절점영역을 설계하기 위해서는 휨모멘트의 작용방향에 따른 절점영역 내부의 응력변화를 정확히 예측하는 것이 매우 중요하다. 본 연구에서는 다양한 형태의 헌치를 갖는 강절점영역의 설계에 있어서 현행의 도로교설계기준이 유용한지에 대해 검토하였다. 또한 선형탄성유한요소해석을 통해 휨모멘트의 작용시의 헌치를 갖는 절점영역내부의 응력상태를 파악한 다음, 이를 바탕으로 스터럿-타이 모델을 제안하였다. 본 연구를 통해 제안한 스터럿-타이 모델은 선형탄성유한요소와 동등수준의 정확도를 가지는 것을 확인하였고, 다양한 형태의 헌치를 갖는 강절점 영역의 보강철근 설계에 유용할 것으로 사료된다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 추계 학술발표회 논문집
• /
• pp.269-272
• /
• 2006

The anchorage zone of prestressed concrete members is a critical region where a large concentrated force due to prestressing by tendons is introduced. In this study, the ACI, AASHTO LRFD, CEB-FIP design criteria and the nonlinear strut-tie model approach are applied to the ultimate strength analysis of simple anchorage zones of 18 post-tensioned concrete members tested to failure. From the result of ultimate strength analysis, the advantages and disadvantages of each method are compared and discussed.

• 대한토목학회논문집
• /
• 제33권1호
• /
• pp.115-130
• /
• 2013

철근콘크리트 파일캡의 설계 시 사용되고 있는 현행 설계기준의 단면법 및 스트럿-타이 모델 방법은 각각 B-영역으로 이루어진 철근콘크리트 구조부재의 거동과 2차원 응력교란영역을 갖는 철근콘크리트 구조부재의 거동에 기초한 것으로, 이를 응력교란영역(D-영역)을 갖고 3차원 거동이 지배적인 철근콘크리트 파일캡의 설계에 적용하는 것은 적절하지 않다. 이 연구에서는 3축 응력을 받는 콘크리트 스트럿 및 절점영역의 강도특성과 철근이 배치되지 않은 인장영역에서의 콘크리트 타이의 하중저항능력 등을 반영하여 철근콘크리트 파일캡을 합리적으로 설계할 수 있는 개선 3차원 스트럿-타이 모델을 제안하였다. 파괴실험이 수행된 78개 철근콘크리트 파일캡 시험체의 극한강도를 현행 설계기준의 단면법 및 스트럿-타이 모델 방법, 그리고 이 연구의 개선 3차원 스트럿-타이 모델을 이용하여 평가하였으며, 그 결과의 비교분석을 통해 스트럿-타이 모델 방법 적용 시의 3차원 거동 및 하중전달 메커니즘을 묘사하기 위한 적절한 구성요소의 필요성과 이 연구에서 제안한 개선 3차원 스트럿-타이 모델의 타당성을 검증하였다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제7권4호
• /
• pp.159-169
• /
• 2003

춤이 깊은 보 설계를 위한 현행 ACI 기준은 콘크리트 압축강도 40MPa이하의 실험결과를 바탕으로 한 반 경험적인 제안식으로서 40MPa이상 고강도콘크리트의 사용이 증가됨에 따라 현행 기준의 고강도 깊은 보에 대한 적용성 평가가 요구되고 있다. 고강도 깊은 보의 전단강도 예측을 위하여 본 연구에서는 콘크리트강도와 모멘트효과를 고려한 수정 연화 스트럿-타이 모델을 제시하였다. 제안모델 평가를 위하여 4개의 시험체를 제작하였으며, 콘크리트 압축강도 49~78MPa로 제작된 74개의 기존 실험 데이터를 적용하여 ACI 318-99 11.8기준, ACI 318-02 부록 A STM의 해석결과와 비교 평가하였다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2000년도 가을 학술발표회논문집(I)
• /
• pp.617-622
• /
• 2000

In this study, effective compressive strength and nodal zone of Strut-and-Tie Model are studied to propose a new design method for RC T-type pier coping for prevention of sudden brittle failure. The coping which transmits loads of bridge to pier should be properly designed to retain ductile behavior. In order to carry out this proper design using STM, tie must yield before concrete fails, and a stress at strut should not exceed a certain effective stress. Therefore, reasonable determination of the effective compressive strength of strut by considering stress states at the nodal zone exactly is very important. Since conventional STM is applied under assumption that all nodes are under hydrostatic stress state, actual non-hydrostatic stress state in nodal zone caused by geometrical characteristics, loading conditions, support conditions of structures can not be considered properly. In order to apply STM for design of RC T-type pier coping, the non-hydrostatic stress state of nodal zone is considered and effective compressive strength is proposed. Then, a new design method of RC T-type pier coping which applies the principle of superposition to obtain optimum ductile behavior is rationally designed.

• Structural Engineering and Mechanics
• /
• 제73권2호
• /
• pp.143-152
• /
• 2020

Deep coupling beams are more prone to suffer brittle shear failure. The addition of steel fibers to seismic members such as coupling beams can improve their shear performance and ductility. Based on the test results of steel fiber reinforced concrete(SFRC) coupling beams with span-to-depth ratio between 1.5 and 2.5 under lateral reverse cyclic load, the shear mechanism were analyzed by using strut-and-tie model theory, and the effects of the span-to-depth ratio, compressive strength and volume fraction of steel fiber on shear strengths were also discussed. A simplified calculation method to predict the shear capacity of SFRC deep coupling beams was proposed. The results show that the shear force is mainly transmitted by a strut-and-tie mechanism composed of three types of inclined concrete struts, vertical reinforcement ties and nodes. The influence of span-to-depth ratio on shear capacity is mainly due to the change of inclination angle of main inclined struts. The increasing of concrete compressive strength or volume fraction of steel fiber can improve the shear capacity of SFRC deep coupling beams mainly by enhancing the bearing capacity of compressive struts or tensile strength of the vertical tie. The proposed calculation method is verified using experimental data, and comparative results show that the prediction values agree well with the test ones.

• 건축구조
• /
• 제15권1호
• /
• pp.66-75
• /
• 2008

• Computers and Concrete
• /
• 제17권1호
• /
• pp.141-156
• /
• 2016

The search for new structural systems capable of associating performance and safety requires deeper knowledge regarding the mechanical behavior of structures subject to different loading conditions. The Strut-and-Tie Model is commonly used to structurally designing some reinforced concrete elements and for the regions where geometrical modifications and stress concentrations are observed, called "regions D". This method allows a better structural behavior representation for strength mechanisms in the concrete structures. Nonetheless, the topological model choice depends on the designer's experience regarding compatibility between internal flux of loads, geometry and boundary/initial conditions. Thus, there is some difficulty in its applications, once the model conception presents some uncertainty. In this context, the present work aims to apply the Strut-and-Tie Model to nonlinear structural elements together with a topological optimization method. The topological optimization method adopted considers the progressive stiffness reduction of finite elements with low stress values. The analyses performed could help the structural designer to better understand structural conceptions, guaranteeing the safety and the reliability in the solution of complex problems involving structural concrete.

• Computers and Concrete
• /
• 제10권3호
• /
• pp.259-276
• /
• 2012

A total of nine reinforced concrete corbels were tested, in this study. Six were externally strengthened with carbon fiber reinforced plastics (CFRP), in the horizontal direction. The cross-sectional area of CFRP and the shear span-to-effective depth ratios are the parameters considered, in this study. Test results indicate that the higher the cross-sectional area of CFRP, the higher is the shear strength of the corbels, and the lower the shear span-to-effective depth ratios, the higher is the shear strength of corbels. The shear strength predicted by the design provisions in section 11.8 of the ACI Code, the strut-and-tie model in Appendix A of the ACI Code, and the softened strut-and-tie (SST) model were compared with the test results. The comparisons show that both the strut-and-tie model in Appendix A of the ACI Code, and the SST model can accurately predict the shear strength of reinforced concrete corbels, strengthened with CFRP.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2003년도 가을 학술발표회 논문집
• /
• pp.409-412
• /
• 2003

ACI design code is not capable of evaluating the inter-effects between concrete and torsional reinforcement on the torsional resistance of the reinforced concrete beams. In this study, the failure strengths of the ten reinforced concrete beams subjected to pure torsion were evaluated using 3-dimensional strut-tie models. The analysis results obtained from the present study were compared with those obtained from the ACI design code. The comparison showed that the accuracy and performance of the present method were better than the ACI design code. Thus, the method implementing a 3-dimensional strut-tie model can be possibly applied to the analysis and design of the reinforced concrete beams subjected to pure torsion as a rational design method.