• Journal of Korean Society of Steel Construction
• /
• v.23 no.1
• /
• pp.113-124
• /
• 2011

This study concerned the interoperability between the structural-analysis model and the default detail model in steel structures available for the structural-design process based on BIM. The purpose of the study was to develop an interface module that can perform data conversion between the analysis and design applications and the BIM applications, through the dotnet frame work development environment using OpenAPI provided by the BIM application vendor. The direct-link method was applied for BIM interoperability. A basic-frame model for detail design and modeling was created from the structural-analysis model to verify if the application was developed. Finally, the proposed process was compared with the existing process to verify the efficiency of the former.

• Journal of the Society of Naval Architects of Korea
• /
• v.57 no.3
• /
• pp.175-181
• /
• 2020

For the success of a structural integrity management, it is essential to acquire structural response data at some critical locations with limited number of sensors. In this study, the structural response of numerical model was estimated by data fusion approach based on the Kalman filter known as stochastic recursive filter. Firstly, transient direct analysis was conducted to calculate the acceleration and strain of the numerical standing beam model, then the noise signals were mixed to generate the numerical measurement signals. The acceleration measurement signal was provided to the Kalman filter as an information on the external load, and the displacement measurement, which was transformed from the strain measurement by using strain-displacement conversion relationship, was provided into the Kalman filter as an observation information. Finally, the Kalman filter estimated the displacement by combining both displacements calculated from each numerically measured signal, then the estimated results were compared with the results of the transient direct analysis.

• International Journal of Aeronautical and Space Sciences
• /
• v.8 no.1
• /
• pp.87-94
• /
• 2007

Tilt rotor-wing concept to show enhanced performance in low speed mission is presented. Three types of stud wings on the existing tilt rotor configuration are suggested and their characteristics are compared. Aerodynamic analysis indicates that the stud wing concept gives significant performance improvement on the endurance and range in the low speed regime when compared with the tilt rotor. Penalties of the stud wing are discussed from the perspectives of conversion corridor, structural weight, configuration design, and cross wind stability. This study concludes that the advantage of the stud wing in general UAV mission performance is so significant as to surpass the penalties in other perspectives investigated.

• Journal of Advanced Marine Engineering and Technology
• /
• v.15 no.3
• /
• pp.31-38
• /
• 1991

Due to the structural complexity and the mutual interference of "water columns", the estimations of absorption power for a large wave energy conversion devices of flosting type in ocean could not achieve the desired results. Thus, in this paper the authors will propose a new methodology based on the three dimensional source ditribution method. We distributed the source to the device and the thin & light plate in "water column", And from the behaviour of this plated, the power and the pressure in water column are calculated. But, yet method should be proved to be valid by experiment.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1992.11a
• /
• pp.49-54
• /
• 1992

Devices of ITO/CdS/CdTe/Te/Al were prepared by Electron-Beam deposition under a vacuum of $7{\times}10^{-6}$[torr]. Optical, Electrical, Structural and Photovoltaic properties of thin film CdS/CdTe at substrate. temperature 300~500[$^{\circ}C$] were also investigated, The structure of CdTe films deposited was of the zincblende type a preferential orientation of the (111) plane parallel to the substrate, the CdTe dark resistivity was about $10^6[{\Omega}cm]$. The conversion, efficiency of the cell increased with increasing substrate temperature. The best-fabricated Cell was a conversion efficiency of 9.1[%].

• Electrical & Electronic Materials
• /
• v.10 no.10
• /
• pp.1034-1040
• /
• 1997

A solar cell conversion effiency was degraded by grain boundary effect in polycrystalline silicon. Grain boundaries acted as potential barriers as well as recombination centers for the photo-generated carriers. To reduce these effects of the grain boundaries we investigated various influencing factors such as emitter thickness thermal treatment preferential chemical etching of grain boundaries grid design contact metal and top metallization along boundaries. Pretreatment in $N_2$atmosphere and gettering by POCl$_3$and Al were performed to obtain multicrystalline silicon of the reduced defect density. Structural electrical and optical properties of slar cells were characterized before and after each fabrication process. Improved conversion efficiencies of solar cell were obtained by a combination of pretreatment above 90$0^{\circ}C$ emitter layer of 0.43${\mu}{\textrm}{m}$ Al diffusion in to grain boundaries on rear side fine grid finger top Yb metal and buried contact metallization along grain boundaries.

• Proceedings of the KIEE Conference
• /
• 1997.07d
• /
• pp.1430-1432
• /
• 1997

A solar cell conversion effiency was degraded by grain boundary effect in polycrystalline silicon. To reduce these effects of the grain boundaries, we investigated various influencing factors such as preferential chemical etching of grain boundaries, grid design, transparent conductive thin film, and top metallization along grain boundaries. Pretreatment in $N_2$ atmosphere and gettering by $POCl_3$ and Al were performed to obtain polycrystalline silicon of the reduced defect density. Structural, electrical, and optical properties of solar cells were characterized. Improved conversion efficiencies of solar cell were obtained by a combination of Al diffusion into grain boundaries on rear side, fine grid finger, top Yb metal grid on Cr thin film of $200{\AA}$ and buried contact metallization along grain boundaries.

• Journal of the Korean Ceramic Society
• /
• v.53 no.6
• /
• pp.615-621
• /
• 2016

SiC-polycrystalline fiber (Tyranno SA, Ube Industries, Ltd.) shows very high heat-resistance and excellent mechanical properties up to very high temperatures. However, further increase in the strength is required. Up to now, we have already clarified the relationship between the strength and the defect-size of the SiC-polycrystalline fiber. The defects are formed during the conversion process from the raw material (amorphous Si-Al-C-O fiber) into SiC-polycrystalline fiber. In this conversion process, a degradation of the Si-Al-C-O fiber and a subsequent sintering of the degraded fiber proceed as well, accompanied by a release of CO gas and compositional changes, to obtain the dense SiC-polycrystalline fiber. Since these changes proceed in each filament, the strict control should be needed to minimize residual defects on the surface and in the inside of each filament for achieving the higher strength. In this paper, the controlling factors of the fiber strength and the fine structure will appear.

• Bulletin of the Korean Chemical Society
• /
• v.28 no.11
• /
• pp.1973-1979
• /
• 2007

Novel organic dyes, JK-34, JK-35 and JK-36 containing bis-dimethylfluorenyl amino coumarin unit are designed and synthesized. Nanocrystalline TiO2 dye-sensitized solar cells were fabricated using these dyes. Under standard global AM 1.5 solar condition, the JK-34 sensitized cell gave a short circuit photocurrent density of 10.05 mA cm?2, open circuit voltage of 0.65 V, and a fill factor of 0.68, corresponding to an overall conversion efficiency η of 4.54%. We found that the power conversion efficiency was shown to be quite sensitive to the structural modifications of bridging thiophene moiety.

• Journal of Microbiology
• /
• v.41 no.4
• /
• pp.335-339
• /
• 2003

Many genetic variants of ${\alpha}_1$-antitrypsin have been associated with early onset emphysema and liver cirrhosis. However, the detailed structural basis of pathogenic ${\alpha}_1$-antitrypsin molecules is rarely known. Here we found that a recombinant $M_{malton}$ variant (Phe52-deleted) lost inhibitory activity by spontaneous conformational conversion into a more stable, inactive form under physiological conditions. Biochemical and spectroscopic data suggested that the variant converts into a reactive center loop-inserted conformation, resembling the latent form of plasminogen activator inhibitor-1.