• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.437-438
• /
• 2006

Generally, the vertical roll process is used to achieve extensive width reduction in hot strip mill. However, it is difficult to avoid the defects such as dog-bone and seam-defect. The sizing press has been developed in response to the defects mentioned above. Especially, this study is carried out to investigate the deformation of slab by two-step sizing press. The deformation behavior in the width sizing process is more favorable than that in conventional vertical rolling edger. The objective of this study is to determine the optimal anvil shape parameters in the sizing press with two-step die from the viewpoint of edge-seam length. In general, the edge-seam defect occurs parallel to the rolling direction at both edges in horizontal rolling process after sizing press. The optimal combination of the parameters is determined by FE-simulation and Artificial Neural Network (ANN). The slab deformation in sizing press with convex anvil is analyzed by FE-simulation. The most suitable profile of the anvil is also discussed fur the improvement of trimming loss because of the side seam defect by FE-simulation and ANN.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.4 s.247
• /
• pp.364-372
• /
• 2006

In this paper, we present a finger tip tactile sensor which can detect contact normal force as well as slip. The sensor is made up of two different materials, such as polyvinylidene fluoride (PVDF) known as piezoelectric polymer, and pressure variable resistor ink. In order to detect slip on the surface of the object, two PVDF strips are arranged along the normal direction in the robot finger tip and the thumb tip. The surface electrode of the PVDF strip is fabricated using silk-screening technique with silver paste. Also a thin flexible force sensor is fabricated in the form of a matrix using pressure variable resistor ink in order to sense the static force. The developed tactile sensor is physically flexible and it can be deformed three-dimensionally to any shape so that it can be placed on anywhere on the curved surface. In addition, a tactile sensing system is developed, which includes miniaturized charge amplifier to amplify the small signal from the sensor, and the fast signal processing unit. The sensor system is evaluated experimentally and its effectiveness is validated.

• Journal of Ocean Engineering and Technology
• /
• v.31 no.5
• /
• pp.335-339
• /
• 2017

This study investigated the sea trial performance of a wave piercing high speed planing hull (WPH). The bow shape of the boat is sharp, and it has no chine or spray strip like a normal planing boat. The skeg is attached to the bottom of the boat in the longitudinal direction from the bow to the stern. The speed performance was analyzed as the speed dropped in a wave, and the seakeeping performance was compared with that of a planing boat with a similar velocity coefficient by measuring the vertical acceleration of the bow in the wave. The turning circle was compared with Lewandowski's estimation for a planing boat. As a result of this study, it was confirmed that the velocity drop of the developed WPH was not large in a wave, and the vertical acceleration was greatly reduced compared with that of a normal planing boat. The turning circle was somewhat larger than the estimated results for a planing boat, but the overall tendency was the same.

• Transactions of Materials Processing
• /
• v.16 no.7
• /
• pp.516-520
• /
• 2007

As the springback of sheet metal during unloading nay cause deviation from a desired shape, accurate prediction of springback is essential for the design of sheet stamping operations. On the removal of the applied load the specimen loses its elastic strain by contracting around the contour of the block, the radius $\rho$ can be determined by the residual differential strain. Therefore in this study the springback estimated by the residual differential strain is experimentally validated through the comparison with those obtained by U-bending test. The springback characteristics of two analytical models are also estimated at various processing conditions such as thickness, curvature of radius and drawing strain. The model based on residual differential strain has an applied transition strain where the springback undergoes a dramatic decrease. Both models show that springback decreases with increased strip thickness and with decreased radius of curvature. For no applied tension, the model based on residual differential strain predicts more springback as compared to the moment based model.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.12
• /
• pp.100-108
• /
• 2004

In reverse engineering, data acquisition methodology can generally be categorized into contacting and non-contacting types. Recently, researches on hybrid or sensor fusion of the two types have been increasing. In addition, efficient construction of a geometric model from the measurement data is required, where considerable amount of user interaction to classify and localize regions of interest is inevitable. Our research focuses on the classification of each bounded region into a pre-defined feature shape fer a hybrid measuring scheme, where the overall procedures are described as fellows. Firstly, the physical model is digitized by a non-contacting laser scanner which rapidly provides cloud-of-points data. Secondly, the overall digitized data are approximated to a z-map model. Each bounding curve of a region of interest (featured area) can be 1.aced out based on our previous research. Then each confined area is systematically classified into one of the pre-defined feature types such as floor, wall, strip or volume, followed by a more accurate measuring step via a contacting probe. Assigned to each feature is a specific digitizing path topology which may reflect its own geometric character. The research can play an important role in minimizing user interaction at the stage of digitizing path planning.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.9 no.6
• /
• pp.162-167
• /
• 2006

The urban stream includes the channel and sandbars. The sandbar plays a key role in the riparian ecosystem. For birds and insects the sandbar offers a small strip of habitat and fish and other fauna feed in the boundary of sandbar where eddies occur. So, it is important habitat and source for the flow of energy, matter and organisms through the landscape and act as ecotone between the terrestrial and stream corridors. However, the sandbar changes continuously by the natural process. Thus, it is necessary to measure the shape and area of the sandbar accurately for the efficient urban stream management for the amenity of urban residents and stream protection. The study site is Yangjae Stream where the first natural-style urban stream restoration projected was impelemented by the support of Ministry of Education in Korea. The measurement was taken by the beacon Differential Global Positioning System (DGPS) and the data were stored and analyzed using ArcView Geographic Information System (GIS) program. Therefore, the purpose of this study is to measure the change of sandbars in the urban stream after concentrated stormwater during summer.

• Journal of the Korean Society of Safety
• /
• v.25 no.3
• /
• pp.100-106
• /
• 2010

Most of the school buildings were built before the seismic code was established. To consider the sunlight and ventilation to the partition walls are built about 1m height beside columns at typical school buildings. For the reason, columns which is consisted school building occur brittle failure shape by the reduced effective depth. In this study, experimental test for retrofitting effect by Aramid Fiber Reinforced Polymers(AFRP) strips on masonry infilled reinforced concrete(RC) frames is performed. The test results were to ensured enough time to evacuate due to the enhancement of ductility and strength of school buildings to withstand earthquakes using AFRP strips.

• Smart Structures and Systems
• /
• v.8 no.1
• /
• pp.39-52
• /
• 2011

We are developing a biomimetic robot based on the Sea Lamprey. The robot consists of a cylindrical electronics bay propelled by an undulatory body axis. Shape memory alloy (SMA) actuators generate propagating flexion waves in five undulatory segments of a polyurethane strip. The behavior of the robot is controlled by an electronic nervous system (ENS) composed of networks of discrete-time map-based neurons and synapses that execute on a digital signal processing chip. Motor neuron action potentials gate power transistors that apply current to the SMA actuators. The ENS consists of a set of segmental central pattern generators (CPGs), modulated by layered command and coordinating neuron networks, that integrate input from exteroceptive sensors including a compass, accelerometers, inclinometers and a short baseline sonar array (SBA). The CPGs instantiate the 3-element hemi-segmental network model established from physiological studies. Anterior and posterior propagating pathways between CPGs mediate intersegmental coordination to generate flexion waves for forward and backward swimming. The command network mediates layered exteroceptive reflexes for homing, primary orientation, and impediment compensation. The SBA allows homing on a sonar beacon by indicating deviations in azimuth and inclination. Inclinometers actuate a bending segment between the hull and undulator to allow climb and dive. Accelerometers can distinguish collisions from impediment to allow compensatory reflexes. Modulatory commands mediate speed control and turning. A SBA communications interface is being developed to allow supervised reactive autonomy.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.03a
• /
• pp.633-640
• /
• 2005

Most existing methods for the footing settlement estimation are for either isolated or strip footings. No sufficient details are available for settlement calculation of footings with different shapes and multiple footing conditions, which are commonly adopted in actual construction projects. In this paper, estimation of footing settlements for various footing conditions of different shapes and multiple conditions is investigated based on Schmertmann's method with focus on values of the strain influence factor $I_z$. In order to examine the effect of multiple footing conditions, field plate load tests are performed in sands using single and double plates. 3D non-linear finite element analyses are also performed for various footing conditions with different footing shape and distance ratios. Results obtained in this study indicate that there are two significant components in the strain influence diagram that need to be taken into account for settlement estimation of rectangular and multiple footings: depth of $I_{zp}$ and depth of strain influence zone. Based on results from experimental and 3D non-linear finite element analyses, improved strain influence diagrams available for various footing conditions are proposed.

• Journal of the Korean Society of Costume
• /
• v.61 no.2
• /
• pp.102-115
• /
• 2011

This study is about reproduction of Yoseon-Cheobli excavated from Byun-su tomb in earlier Joseon Dynasty. There are three Yoseon-Cheobli in Byun-su tomb. The producing process is made in concrete by suggesting the process of producing clothing. Based on the Annals of the Joseon Dynasty, the most frequently recorded one, was reproduced by dying fabric with safflower and indigo plants. Through the research about their specific size, sewing method and construction, it have been produced in the following. First, the revealing that collar to be half-square and to compose the line in the center of collar. The width of the collar is 11.6 12.1cm. Second, the 21~22 pairs of waist lines that are 13~14cm in width fixed at intervals of 0.3cm. The method of making waist lines is twisting either fabrics or silk threads. Third, fine gathering around the part of the waist of skirt, and the size of fold surface is 0.2cm. Sewing method needs running stitch and backstitch. As the result of producing the cloth, it became to possess more ornamental features after transformation suitable to the new environment while the same remained functional features for everyday life such as a dressing shape, length of the bodice and curvy completion line of a collar strip.