• 한국축산시설환경학회지
• /
• 제5권2호
• /
• pp.79-86
• /
• 1999

Recently more dairy farmers are interested in the utilization of stretch film for wrapping silage material. Most of stretch film are imported from abroad and one domestic product was developed, but its quality has not yet been tested. Therefore this study was executed to offer basic data on this material to the farmers. Measured items were tensile load, extension ratio, and tear propagation strength of stretch films. Comparisons were made among the white color of domestic product(Kw), and white(Fw), black (Fb) and green color(Fg) of foreign products. The result were summarized as follows: 1. Tensile loads of lengthwise direction in stretch films were 557.4, 377.4, 282.6 and 398.4kgf/$\textrm{cm}^2$ in Kw, Fw, Fb and Fg, respectively, and tensile loads of width direction were 415.9, 418.1, 360.2 and 433.0kgf/$\textrm{cm}^2$ in Kw, Fw, Fb and Fg, respectively. 2. Extension ratios of lengthwise direction were 650, 462.5, 512.5% and 537.5% in Kw, Fw, Fb and Fg, respectively, Extension ratios of width direction were 930, 962.5, 950 and 1,000% in Kw, Fw, Fb and Fg, respectively. 3 Tear propagation strength of lengthwise direction 187.9, 148.9, 157.3 and 142.8kgf/cm, and tear propagation strength of width direction were 141.4, 129.8, 140.4 and 106.6kgf/cm in Kw, Fw, Fb and Fg, respectively. 4. In the light transmittance, there was no difference between white and green color stretch film, but it was very low in black one. Therefore, it is thought that research on quality of roll bale silage treated with each stretch film would be needed.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1998년도 제2회 박판성형심포지엄 논문집 박판성형기술의 현재와 미래
• /
• pp.121-130
• /
• 1998

In order to analyze the forming characteristics of laser welded tailored blanks, laser welded blanks of different thickness and strength combinations were prepared and tensile, stretching, stretch flanging and deep drawing tests were done. The tensile elongation perpendicular to the weld line, stretching and stretch flanging formability decreased with increasing the deformation restraining force (strength ${\times}$ thickness) ratio between two welded sheets. The tensile elongation along weld line reached a value above 90% of the single sheet's elongation. Stretch flanging formability was reduced to approximately 10% of the single sheet value when the deformation restraining force ratio between two welded sheets was increased to two. Weld line movement of deep drawing test specimens was also affected by the strength ratio of the combined sheets, the weld line location and forming conditions. In all forming modes of tailored blanks, excessive weld line movement resulted from strain concentrations at the weaker sheet and resulted in fracture of the weaker side.

• 소성∙가공
• /
• 제30권2호
• /
• pp.74-82
• /
• 2021

Stretch-flangeability, which is the ability of sheet steels to be deformed into complex shapes, is a critical formability property in automobile body parts. In this study, the center-hole for hole expansion test, which is normally used to evaluate the stretch-flangeability of sheet steels, was prepared by both punching and electrical discharge machining (EDM) methods. Hole expansion ratio (HER) of punched hole was far lower than the HER of EDM drilled hole because of damage/crack in hole-edge due to punching process. The effect of hole-edge condition on HER was quantified by mechanical, fractographic and geometric factors. Based on these factors, the empirical equation used to determine HER for various sheet steels was derived using non-linear regression.

• The Journal of Korean Physical Therapy
• /
• 제27권5호
• /
• pp.299-303
• /
• 2015

Purpose: The objective of this study was to examine the changes in muscle activity on the anterior deltoid muscle depending on the stretch rate of kinesio tape when applying kinesio tape in healthy adult subjects. Methods: This study was a single-blind randomized controlled trial, including 22 healthy participants (male 15, female 7) with no pathology or past history of shoulder who participated voluntarily. Participants applied a different stretch rate of the kinesio tape, and the functional activity was tested. The stretch rate of kinesio tape was 0%, 10%, and 20%. Subjects lifted a weight (5% of their body weight) to their shoulder height. Subjects lifted a weight up to an angle of 90 degrees in the sagittal plane, and muscle activities (biceps brachii, anterior deltoid, middle deltoid, upper trapezius) were assessed using EMG (electromyography). Analysis of muscle activity was divided into two parts (lift weight and keep holding). The EMG activity of each muscle was normalized to the value of reference voluntary contraction (%RVC) and explored using repeated ANOVA. Results: There were no significant differences in muscle activity depending on the ratio of tape stretch when lifting a weight (p>0.05). There were no significant differences in muscle activity depending on the ratio of tape stretch when holding a weight (p>0.05). Conclusion: According to the results of this study, in the case of applying kinesio taping therapy for healthy people, it was found that the stretch rate of the tape does not have an effect on muscle activity.

• 대한기계학회논문집
• /
• 제19권8호
• /
• pp.1982-1988
• /
• 1995

Methane/Air premixed flames are studied numerically, using a detailed chemical model, to investigate the flame strech effects on the extinction in a counterflow. The finite difference method, time integration and modified Newton iteration are used, and adaptive grid technique and grid smoothing have been employed to adjust the grid system according to the spatial steepness of the solution profiles. Results show that the flame stretch, or the conventional nondimensionalized stretch having the tangential flow characteristics of the stretched flame alone cannot adequately describes the extinction phenomena. On the other hand, the local flame stretch having both the normal and tangential flow characteristics of the stretched flame can give a proper explanation to the extinction of the symmetric planar premixed flames stabilized in a counter flow. The extinction condition were found to be a constant local stretch regardless of the equivalence ratio.

• 소성∙가공
• /
• 제9권4호
• /
• pp.339-347
• /
• 2000

For the successful forming of tailored blank, it is important to control the deformation of the stretch flange mode, which is strong1y dependent upon the location of weld line and blank shape. In order to investigate the effects of tailored blank design factors on the stretch flange forming, we made the model die which can simulate stretch flange mode. Taguchi method was employed to analyze the sensitivity of blank design factors for the forming of tailored blank. From the results of experiment S/N ratios were calculated and using Variance Analysis, significance of parameters and optimal condition of each factors were extracted. Based on these analyses, the weld line height and the strength ratio and the arc center height were selected as effective parameter. The analysed result was practically applied for Side outer panel stamping process.

• Fibers and Polymers
• /
• 제6권4호
• /
• pp.339-342
• /
• 2005

In this paper, a hand-operating method (tiled test method) of the wool-blending sample is made out, and make use of the method, the test of wool-blending bundle in different blending ratio is accomplished. According to the test data, the synthesis method of the stretch curve is worked out and the synthesis software for the typical stretch curve of wool-blending bundle is designed. Through laboratory hand-operating method, the blending fasciculus applying to fiber bundle test can be obtained in a short time. Calculation for sampling is accomplished in the article. We bring up 9 new signs to describe the characteristics of the curve behind peak for the first time: elongation behind peak (HE), elongation percentage behind peak (HEP), relative elongation rate behind peak (RHE), total break work $(W_a)$, break work behind peak (HW), break work coefficient behind peak (HWC), elongation percentage of half-load behind peak (HEL), load percentage of half-elongation behind peak (HLE), break efficiency behind peak (HEC).

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2000년도 춘계학술대회논문집
• /
• pp.123-128
• /
• 2000

Fundamental and informative data of axi-symmetric stretch-drawing of several sheetmetals with thicknesses of 0.7-1.0mm are presented both for single and double operations. Very small radius is applied to the die profile (or-shoulder) ion all operations. to induce wall-thinning by the effect of bending-under-tension from which the name 'stretch-drawing' comes. It is clearly demonstrated that deeper cups could be formed by single and double stretch-drawings from smaller circular blanks due to such wall-thinning action than in the usual deep-drawing of larger blanks, From this fact it is emphasized that the deep-drawability of a sheet metal is not evaluated simply by the conventional L.D.R (limiting drawing ratio) but the depth of the drawn cup should also be taken into account./ Many experimental data about various metals and thicknesses given in this paper offer a valuable information in this process for more general use which recommends to replace the conventional deep-drawing process by the stretch-drawing process both for single and double operations. In the single stretch-drawing it is also confirmed that a deeper cup can be produced by raising the blank-holding force at later stage of operation.

• 대한산업공학회지
• /
• 제40권6호
• /
• pp.642-647
• /
• 2014

In this paper, a hybrid genetic algorithm (HGA) approach is proposed for an n-job, m-machine flow shop scheduling problem with limited capacity buffers with blocking in which the objective is to minimize the total stretch. The stretch of a job is the ratio of the amount of time the job spent before its completion to its processing time. HGA adopts the idea of seed selection and development in order to improve the exploitation and exploration power of genetic algorithms (GAs). Extensive computational experiments have been conducted to compare the performance of HGA with that of GA.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2003년도 추계학술대회
• /
• pp.406-411
• /
• 2003

It is clearly demonstrated that deeper cups could be formed by single and double stretch-drawings from smaller circular blanks due to such wall-thinning action than in the usual deep-drawing of larger blanks. From this fact, it is emphasized that the deep-drawability of a sheet metal Is not evaluated simply by the conventional L.D.R (limiting drawing ratio), but the depth of the drawn cup should also be taken into account. Many experimental data about various metals and thicknesses given in this paper offer a valuable information in this process for more general use which recommends to replace the conventional deep-drawing process by the stretch-drawing process both for single and double operations. In the single stretch-drawing, it is also confirmed that a deeper cup can be produced by raising the blank-holding force at later stage of operation.