• Journal of Biosystems Engineering
• /
• 제15권3호
• /
• pp.219-229
• /
• 1990

The compression creep behavior of grains when loaded depends not only on load but also on duration of load application. The most common methods of studying the load-time characteristics of agricultural products is by employing rheological models such as Burger's model. However it is sometimes not sufficient to describe the viscoelastic behavior of grains to be Burger's model. For this reason, this study was conducted to develop the rheological model which represented the creep compliance response of the rough rice kernel and was a function of initial stress applied and time. The effects of the initial stress applied and the moisture content on the compression creep behavior of the rough rice kernel were analyzed. The results were obtained from the study as follows: 1. Since the viscoelastic behavior of the rough rice kernel was nonlinear, the transient and steady state creep compliance was satisfactorily modelled as follows: $$J({\sigma},t)=A{\sigma}^B[C+Dt-exp(-Ft)]$$ But, for the every stress applied, the compression creep behavior of the samples tested can be well described by Burger's model respectively. 2. The creep compliance, the instantaneous elastic strain, the retarded elastic strain and the viscous strain of the sample tested generally increased in magnitude with increasing the applied initial stress and the moisture content used in the tests. At low moisture content, the creep compliance for the Japonica-type rough rice kernel Was a little higher than those for Indica-type and at high moisture content, vice versa at high moisture content. 3. The retardation times of the samples had not an uniform tendency by the initial stress and the moisture content. The retardation times ranged from 0.66 to 6.76 seconds, and the creep progressed from transient to steady state at a relatively high rate. 4. The less viscous strain than the instantaneous elastic strain for the samples tested indicated that rough rice kernel behaved as a viscoelastic body characterized by elasticity than viscosity.

• Nuclear Engineering and Technology
• /
• 제51권4호
• /
• pp.1060-1068
• /
• 2019

This work aims to establish a model of a primary water stress corrosion crack growth rate of Alloy 690 material for the head penetration nozzles of Korean pressurized water reactors. The test material had an inhomogeneous microstructure with bands of fine-grains and intragranular carbides in the matrix of coarse-grains, which was similar to the archive materials of the head penetration nozzles. The crack growth rate was measured from the strain-hardened materials as a function of the stress intensity factor in simulated primary water at various temperatures and dissolved hydrogen contents. The effects of strain-hardening, temperature, and dissolved hydrogen on the crack growth rate were analyzed independently, and were then introduced as normalizing factors in the crack growth rate model. The crack growth rate model proposed in this work provides a key element of the tools needed to assess the progress of a stress corrosion crack when detected in thick-wall Alloy 690 components in Korean reactors.

• 한국기계가공학회지
• /
• 제17권4호
• /
• pp.64-69
• /
• 2018

This paper investigates the compressive deformation behavior of direct metal tooling (DMT), processing titanium alloy (Ti-6Al-4V) parts under high strain loading conditions. Split Hopkinson Pressure Bar (SHPB) experiments were performed to determine the flow stress and the coefficients of the Johnson-Cook model. This model is described as a function of strain, strain rate, and temperature. SHPB experiments were performed to characterize the deformation behavior of specimens made with 3D printers, using Ti-6Al-4V material under high temperature and dynamic loading.

• 소성∙가공
• /
• 제31권4호
• /
• pp.194-199
• /
• 2022

In finite element method (FEM) simulations, constitutive models are widely used and developed to represent a wide range of true stress-strain curves using a small number of modeling parameters. Nevertheless, many studies has been conducted to find a suitable constitutive model and optimal modeling parameters to represent experimentally obtained true stress-strain curves. Therefore, in this study, a new constitutive modeling approach using the combined Swift and Voce model is suggested, and confirmed through comparisons of the experimental results with the FEM simulation results.

• Structural Engineering and Mechanics
• /
• 제51권4호
• /
• pp.627-641
• /
• 2014

Functionally graded steels (FGSs) are a family of functionally graded materials (FGMs) consisting of ferrite (${\alpha}$), austenite (${\gamma}$), bainite (${\beta}$) and martensite (M) phases placed on each other in different configurations and produced via electroslag remelting (ESR). In this research, the flow stress of dual layer austenitic-martensitic functionally graded steels under hot deformation loading has been modeled considering the constitutive equations which describe the continuous effect of temperature and strain rate on the flow stress. The mechanism-based strain gradient plasticity theory is used here to determine the position of each layer considering the relationship between the hardness of the layer and the composite dislocation density profile. Then, the released energy of each layer under a specified loading condition (temperature and strain rate) is related to the dislocation density utilizing the mechanism-based strain gradient plasticity theory. The flow stress of the considered FGS is obtained by using the appropriate coefficients in the constitutive equations of each layer. Finally, the theoretical model is compared with the experimental results measured in the temperature range $1000-1200^{\circ}C$ and strain rate 0.01-1 s-1 and a sound agreement is found.

• Geomechanics and Engineering
• /
• 제25권2호
• /
• pp.75-87
• /
• 2021

Because the hydraulic/mechanical behaviour of unsaturated soil is more complicated than that of saturated soil, one of the most important issues in modelling unsaturated soil is to properly couple its stress-strain relationship with its water retention characteristics. Based on the results of a series of tests, the stress-strain relationship and the changes in suction and saturation of unsaturated completely decomposed granite (CDG, also called Masado) vary substantially under different loading/hydraulic conditions. To precisely model the hydraulic/mechanical behaviour of unsaturated Masado, in this study, the superloading concept was firstly introduced into an existing saturated/unsaturated constitutive model to consider the structural influences. Then a water retention curve (WRC) model considering the volumetric change in the soil, in which the skeleton and scanning curves of the water retention characteristics were assumed to shift in parallel in accordance with the change in the void ratio, was proposed. The proposed WRC model was incorporated into the constitutive model, and the validity of the newly proposed model was verified using the results of tests conducted on unsaturated Masado, including water retention, oedometer and triaxial tests. The accuracy of the proposed model in describing the stress-strain relationship and the variations in suction and saturation of unsaturated Masado is satisfactory.

• 연구논문집
• /
• 통권34호
• /
• pp.59-68
• /
• 2004

The hot spot stress approach and the notch strain approach are discussed with some results of them. And a stress model that can be applicable to several types of weld joints with single S-N curve of the base material. The stress model uses the geometric characteristics of the stress distribution vicinity of weld joints. The model was applied to five different weld joins(the base material is SM490B). By the representative stress, the experimental fatigue data are plotted very closely to the S-N curve of the base material.

• 콘크리트학회논문집
• /
• 제22권4호
• /
• pp.481-488
• /
• 2010

횡구속된 고강도 콘크리트의 역학적 거동을 예측하기 위해 보통강도 콘크리트의 구성모델을 적용할 경우 연성 거동이 과대평가된다. 이러한 문제를 해결하기 위해 콘크리트 강도가 증가함에 따라 구속효과에 미치는 영향을 고찰하여 고강도 콘크리트에 적용 가능한 정확한 응력-변형률 관계가 요구된다. 따라서 이 연구에서는 횡구속된 고강도 콘크리트의 강도와 연성 거동에 양향을 미치는 변수들의 회귀분석을 통한 변수별 회귀식을 바탕으로 새로운 횡구속된 고강도 콘크리트의 구성모델이 제안된다. 횡구속된 고강도 콘크리트의 강도 및 초기강성을 나타내는 응력-변형률 곡선의 상승부는 제안된 구성모델과 잘 일치하였고 연성 거동을 나타내는 하강부 곡선은 원형 단면을 가지는 낮은 횡구속 철근의 항복강도 및 철근비일 때 과대평가되었다. 콘크리트 강도를 주요 변수로 하는 제안된 구성모델은 문헌분석을 통한 25개의 횡구속된 고강도 콘크리트 기둥의 실험적 연구와 비교 분석한 결과 콘크리트 압축강도 60~124 MPa 범위에서의 응력-변형률 곡선과 잘 일치되었다.

• 콘크리트학회논문집
• /
• 제15권5호
• /
• pp.747-758
• /
• 2003

The moment-curvature envelope describes the changes in the flexural capacity with deformation during a nonlinear analysis. Therefore, the moment-curvature analysis for reinforced concrete columns, indicating the available flexural strength and ductility, can be conducted providing the stress-strain relation for the concrete and steel are known. The moments and curvatures associated with increasing flexural deformations of the column may be computed for various column axial loads by incrementing the curvature and satisfying the requirements of strain compatibility and equilibrium of forces. Clearly it is important to have accurate information concerning the complete stress-strain curve of confined high-strength concrete in order to conduct reliable moment-curvature analysis that assesses the ductility available from high-strength concrete columns. However, it is not easy to explicitly characterize the mechanical behavior of confined high-strength concrete because of various parameter values, such as the confinement type of rectilinear ties, the compressive strength of concrete, the volumetric ratic and strength of rectangular ties. So a stress-strain model is developed which can simulate complete inelastic moment-curvature relations of high-strength concrete columns.

• Coupled systems mechanics
• /
• 제2권3호
• /
• pp.271-288
• /
• 2013

In the present study an elastic-plastic strain analysis is carried out for fibrous composites by using numerical modeling. Application of homogeneous transversely-isotropic model was chosen based on problem solution of a square plate with a circular hole under uniaxial tension. The results obtained in this study correspond to the solution of fiber model trial problem, as well as to analytical solution. Further, numerical algorithm and software has been developed, based on simplified theory of small elastic strains for transversely-isotropic bodies, and FEM. The influence of holes and cracks on stress state of complicated configuration transversely-isotropic bodies has been studied. Strain curves and plasticity zones that are formed in vicinity of the concentrators has been provided. Numerical values of effective mechanical parameters calculated for unidirectional composites at different ratios of fiber volume content and matrix. Content volume proportions of fibers and matrix defined for fibrous composite material that enables to behave as elastic-plastic body or as a brittle material. The influences of the fibrous structure on stress concentration in vicinity of holes on boron/aluminum D16, used as an example.