• 한국건설순환자원학회논문집
• /
• 제8권4호
• /
• pp.458-466
• /
• 2020

이 연구의 목적은 비정질 강섬유와 폴리아미드 섬유를 이용한 고성능 하이브리드 섬유보강 콘크리트의 압축 및 인장 거동을 평가하는 것이다. 이를 위하여 목표 압축강도 40MPa 및 60MPa 각각에 대해서 비정질 강섬유와 폴리아미드 섬유를 총 부피비로 1.0% 혼입한 고성능 하이브리드 섬유보강 콘크리트를 제작한 후 압축강도, 압축인성, 직접인장강도 및 응력-변형률 특징 등의 압축 및 인장 거동을 평가하였다. 그 결과, 고성능 하이브리드 섬유보강 콘크리트의 압축강도는 플레인 콘크리크보다 다소 감소하였으나, 압축인성, 압축인성 비, 직접인장강도는 크게 증가하는 것으로 나타났다. 또한 압축 및 인장 시험시 플레인 콘크리트는 최대응력 이후 취성파괴를 나타냈으나, HPHFRC는 변형연화 현상을 나타내어, 압축 및 인장 거동이 크게 개선되는 것으로 나타났다.

• 한국정밀공학회지
• /
• 제20권10호
• /
• pp.199-207
• /
• 2003

The Timoshenko beam model has been known as the most accurate model for representing beam structures. However, the Timoshenko beam model may give rise to a significant error when it is applied to multi-stepped beam structures. This paper is intended to demonstrate the modeling error of Timoshenko beam based finite element model for multi-stepped beam structures and to suggest a new modeling method to improve the accuracy. A tentative bending spring is introduced into the stepped section to represent the softening effect due to the presence of step. This paper also proposes a finite element modeling method in the light with the tentative bending spring model for the step softening effect. The proposed method rigorously adapts computation results from a commercial finite element code. The validity of the proposed method is demonstrated through a series of simulation and experiment.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 춘계학술대회논문집
• /
• pp.135-139
• /
• 1999

The static softening behavior of AISI 4140 could be characterized by the hot torsion test in the temperature ranges of 10$0^{\circ}C$~120$0^{\circ}C$ and strain rate ranges of 0.05/sec~5/sec. Deformation efficiency which was based on dynamic materials model was calculated from flow stress curves obtained continuous deformation. Interrupted deformation was performed with 2 pass deformation in the pass strain ranges of 0.25{{{{ epsilon _p}}}} ~3{{{{ epsilon _p}}}} and interrupted time ranges of 0.5~100sec. The dependences of process variables pass strain ({{{{ epsilon _i}}}}) stain rate ({{{{ {. } atop {$\varepsilon$ } }}}}) temperature (T) and interpass time ({{{{ {t }_{i } }}}}) on static recrystallization (SRX) and metadynamic recrystallization .(MDRX) could be indicidually predicted from the modified Avrami's equations. Comparison of the softening kinetics between MDRX and SRX showed that the rate of MDRX was more rapid than that of SRX for the same deformation variables. Controlled multipass deformations were performed using deformation efficiency static and metadynamic recrystallization of AISI 4140.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1997년도 봄 학술발표회 논문집
• /
• pp.53-60
• /
• 1997

The strain localization of concrete is a phenomenon such that the deformation of concrete is localized in finite region along with softening behavior. The objective of this paper is to develope a consistent algorithm for the finite element modeling of localized zone in the analysis of the strain-localization in concrete. For modeling of the localized zone in concrete under strain localization, a general Drucker-Prager failure criterion which can consider nonlinear strain softening behavior of concrete after peak-stress is introduce. The return-mapping algorithm is used for the integration of the elasto-plastic rate equation and the consistent tangent modulus is derived. Using finite element program implemented with the developed algorithms, strain localization behaviors for the different sizes of concrete specimen under compression are simulated.

• 한국지반공학회논문집
• /
• 제30권7호
• /
• pp.5-15
• /
• 2014

휴 폐광산지는 산발생, 지하수 오염뿐만 아니라 침식 및 산사태 등 다양한 물리화학적 지질재해에 노출되어 있다. 임기광산 폐석적치장 광미를 대상으로 링 전단시험을 수행하여 전단속도에 따른 전단특성을 조사하고 한다. 본 연구에 있어 마찰저항을 최소화할 목적으로 링 전단상자 오링(O-ring)은 전단동안 회전이 가능하도록 설계되었다. 1차 시험은 일정한 수직응력(50kPa)과 전단속도(0.1mm/sec) 조건에서 전단시간에 따른 전단응력을 조사하였다. 2차 시험은 일정한 수직응력 조건에서 전단속도를 0.01, 0.1, 1, 10, 50, 100mm/sec로 순차적으로 증가시켜 전단속도에 따른 전단응력을 조사하였다. 3차 시험은 일정한 전단속도(0.1mm/sec)하에서 수직응력을 20, 40, 60, 80, 100, 150kPa로 증가시켜 각 경우에 대한 전단응력을 조사하였다. 시험결과에 따르면, 배수조건에 관계없이 임기광산 폐석적치장광미시료는 전단연화거동(strain softening behavior)을 보였다. 특히 전단속도가 10mm/sec보다 작은 경우 잔류전단응력은 100~300초 사이에 일정한 값에 도달하는 것으로 나타났다. 2차와 3차 시험결과에 따르면, 배수조건에 관계없이 전단응력은 전단속도와 수직응력의 함수로 나타났다. 하지만, 배수조건에 따라 링 전단상자 전단부에서 상이한 입자파쇄 특성이 관측되었다. 배수조건시 전단상자 전단면에서 하단까지 넓은 전단띠가 형성된 것에 반해, 비배수조건시 전단면에 국부 전단띠가 형성되었다. 이러한 점에 비추어 볼 때, 전단속도에 따른 입자파쇄 특성은 산사태 유동성을 높이는 중요한 인자로 판단된다.

• 지질공학
• /
• 제26권3호
• /
• pp.307-314
• /
• 2016

흙의 전단특성을 조사하기 위하여 다양한 전단시험장치가 사용되고 있다. 특히 흙의 무한변형에 따른 잔류전단강도(residual shear strength)를 측정하고자 할 경우 링전단시험장치가 사용된다. 본 연구는 배수, 압밀 및 전단속도 제어가 가능한 비배수전단강도 측정용 링전단시험장치를 사용하여 전단동안 발생하는 누수현상(water leakage)이 전단특성에 미치는 영향성에 대하여 조사하였다. 실험은 비배수조건에서 동일한 수직응력(50 kPa)을 재하하고 전단속도(0.01, 0.1, 1 mm/sec)를 3단계로 구분하여 적용하였다. 실험결과에 따르면, 동일한 수직응력에서 비배수전단강도는 전단속도에 의존하는 것으로 나타났다. 하지만, 상대적으로 낮은 전단속도(V = 0.01 mm/sec)에서는 변형률 경화 거동(strain hardening behavior)을 보였고 상대적으로 높은 전단속도(V ≥ 0.1 mm/sec)에서는 변형률 연화 거동(strain softening behavior)을 보였다. 시험기 성능평가를 통하여 누수가 발생할 경우 전단속도 크기에 관계없이 전단응력은 증가하는 것으로 나타났다. 누수가 크면 클수록 전단응력이 증가된다. 이러한 실험결과는 전단동안 발생하는 누수로 인한 흙 입자의 재배열과 다짐도의 증가에 따른 것으로 판단된다. 따라서 육안조사 및 반복적인 포화와 압밀과정을 통하여 실험오차를 최소화할 수 있는 작업이 필요하다.

• Journal of Welding and Joining
• /
• 제3권2호
• /
• pp.16-26
• /
• 1985

Post weld heat treatment(PWHT), at more than 600.deg. C, is essential to remove residual stress and hydrogen in weld HAZ and improve fatigue characteristics. However, residual stress during PWHT is responsible for PWHT embitterment and it promotes precipitation of impurities to grain boundary. In this paper, the effect of stress simulated residual stress on fatigue failure was evaluated by fatigue test, microhardness test and fractograph. The obtained results are summarized as follows; (1) The fatigue crack growth rate(da/dN) of parent and heat treated parent was affected by microstructure due to heat treatment and it depended on stress intensity factor (.DELTA.k). (2) The fatigue strength of weld HAZ was dependent on applied stress during PWHT and da/dN after PWHT was slower than as-weld. (3) Softening amount of weld HAZ was bigger than any other due to PWHT. Hardness value of weld HAZ was affected by heat treatment under the applied stress of 10 $kgf/mm^2$, but beyond 20 $kgf/mm^2$ it was increased by the applied stress rather than heat treatment. (4) Beyond the applied stress of 20 $kgf/mm^2$ during PWHT, intergranular fracture surface was observed and its amount was increased with applied stress during PWHT. (5) Effect of applied stress during PWHT on aspect of fracture surface was larger rather than that on fatigue crack growth behavior.

• 한국해양공학회지
• /
• 제11권2호
• /
• pp.39-47
• /
• 1997

Creep rate the elevated temperature is known to be controller by the softening process of microstructure especially in the solid solution alloys such as 125 Cr rotor steel. The change of structure is a decreasing process of the free energy of the state including stress, diffusivity of the material, and tmeperature. This study shows that diffusion coefficient, D of 12% Cr rotor steel at 953K with 74.8 MPa is 1.084~3.140*$10^{15}mm^2sec^1$ compared to $1.658*10^{24}mm^2sec^1$at 963K without stress. During creep, the growth of martensite laths accelerates the diffusion coefficient under stress due to incoherency of interface between carbides and matrix.

• Structural Engineering and Mechanics
• /
• 제5권3호
• /
• pp.239-256
• /
• 1997

The companion paper presents a new three-parameter model for the uniaxial rate-sensitive material response, which is based on a bilinear static stress-strain relationship with kinematic strain-hardening. This paper extends the proposed model to trilinear static stress-strain relationships for steel and concrete, and discusses the implementation of the new models within an incremental-iterative solution procedure. For steel, the three-parameter rate-function is employed with a trilinear static stress-strain relationship, which allows the utilisation of different levels of rate-sensitivity for the plastic plateau and strain-hardening ranges. For concrete, on the other hand, two trilinear stress-strain relationships are used for tension and compression, where rate-sensitivity is accounted for in the strain-softening range. Both models have been implemented within the nonlinear analysis program ADAPTIC, which is used herein to provide verification for the models, and to demonstrate their applicability to the rate-sensitive analysis of steel and reinforced concrete structures.

• Computers and Concrete
• /
• 제22권1호
• /
• pp.11-25
• /
• 2018

A numerical approach for the evaluation of the flexural response of Steel Fibrous Concrete (SFC) cross-sections with arbitrary geometry, with or without conventional steel longitudinal reinforcing bars is proposed. Resisting bending moment versus curvature curves are calculated using verified non-linear constitutive stress-strain relationships for the SFC under compression and tension which include post-peak and post-cracking softening parts. A new compressive stress-strain model for SFC is employed that has been derived from test data of 125 stress-strain curves and 257 strength values providing the overall compressive behaviour of various SFC mixtures. The proposed sectional analysis is verified using existing experimental data of 42 SFC beams, and it predicts the flexural capacity and the curvature ductility of SFC members reasonably well. The developed approach also provides rational and more accurate compressive and tensile stress-strain curves along with bending moment versus curvature curves with regards to the predictions of relevant existing models.