• Journal of Sensor Science and Technology
• /
• v.21 no.4
• /
• pp.276-282
• /
• 2012

Vessels receive stress during their navigations as well as during their cargo operations. This stress may cause damages to the hull and may result in accidents. So the hull stress monitoring system(HSMS) is recommended in order to prevent these accidents. In this paper, we manufactured fiber Bragg grating(FBG) sensor and the model ship for towing tank experiments. The strain characteristics of the model ship on the water wave were measured through the towing tank experiment. The FBG sensors and electric strain gauges were attached on the connection jig, and then the characteristics of the FBG sensor were compared with those of the electric strain gauge. The strain of model ship was increased according to the increment of the amplitude of water wave. In particular, the largest strain was measured in the center of the model ship. As the wave period increased, the strain of model ship was decreased.

• Journal of Biosystems Engineering
• /
• v.19 no.1
• /
• pp.17-21
• /
• 1994

This reasearch was performed to provide the fundamental intonation for the mechanization of Korean pine cone harvest when the shoot shearing method is adopted. Shear force and stress of pine cone shoots were measured and analyzed for this purpose. Samples are selected along their harvesting time and tested in 17 levels of shoot diameter from 10 to 26mm with 1mm increment. 1) Shear force-deformation characteristics showed that shoot reached its rupture point after 2 to 4 of bio-yield points. It was supposed that these multiple bio-yield points were caused by the discrete compression of wood parts which are composed of water, nutrient, resin, etc. 2) Required shear force to shear shoot was proportional to the square of shoot diamter, however, shear force for shoots of early harvesting time(Aug. 31) was proportional to the shoot diameter. Variance of shear force was increased as the harvesting time was delayed. Shear forces were distributed from 468N(Aug. 31, 12mm dia) to 4153N(Aug. 31, 26mm dia) disregarding the sampling date. 3) The average shear stresses by sampling dates were 744,822, and 883N/m2, respectively, and for the earlier shoot samples shear stress was quite smaller than the others. Shear stress was proportional to shoot diameter squared, and the effect of shoot diameter on the shear stress was decreased as harvesting time was delayed.

• Geomechanics and Engineering
• /
• v.20 no.5
• /
• pp.371-384
• /
• 2020

A settlement prediction method based on shear wave velocity measurements and soil nonlinearity was recently developed and verified by means of centrifuge tests. However, the method was only applicable to heavily overconsolidated soil deposits under enlarged yield surfaces. In this study, the settlement evaluation method was refined to consider the stress history of the sublayer, based on an overconsolidation ratio evaluation technique, and thereby incorporate irrecoverable plastic deformation in the settlement calculation. A relationship between the small-strain shear modulus and overconsolidation ratio, which can be determined from laboratory tests, was adopted to describe the stress history of the subsurface. Based on the overconsolidation ratio determined, the value of an empirical coefficient that reflects the effect of plastic deformation over the elastic region is determined by comparing the overconsolidation ratio with the stress increment transmitted by the surface design load. The refined method that incorporate this empirical coefficient was successfully validated by means of centrifuge tests, even under normally consolidated loading conditions.

• Korean Journal of Adult Nursing
• /
• v.22 no.1
• /
• pp.11-18
• /
• 2010

Purpose: The purpose of the study was to identify levels of anxiety, stress hormone, lymphocytes, and neutrophils of the nursing students before an examination and to examine effects of social support on those variables related to taking examinations. Methods: Thirty eight healthy nursing students participated. They completed the questionnaire including state anxiety, test anxiety (VAS scale) and social support two weeks before the exam and again just before the exam. Simultaneously, a venous sample for ACTH, cortisol, lymphocytes & neutrophils count was drawn by a trained nurse. Descriptive statistics, paired t-test, student t-test, and Pearson's correlation with SPSS/WIN 14.0 were used to analyze the data. Results: Test anxiety scores and cortisol level on the exam day showed a significant increment compared with those on the non-exam day. The participants with higher levels of total social support scores showed significantly lower state anxiety on the exam day than those with lower levels of total social support scores. Conclusion: These data indicate a possible alteration in cortisol responsiveness to academic stress in nursing students. Social support would play an important role in modulation of academic stress.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.36 no.3
• /
• pp.90-99
• /
• 1994

To investigate the undrained shear strength characteristics of marine soils with high water content, high compressibility and weak bearing capacity, a series of undrained triaxial tests with pore pressure measurements on undisturbed and disturbed Banwol marine clay in normally consolidated and overconsolidated states is carried out. The results and main conclusions of this study are summarized as follows : 1 . When the consolidation pressure is increased, the maximum deviator stress of disturbed and undistubed clay in normally consolidated state is increased. Pore pressure parameters and internal friction angle of undisturbed clay are greater than those of disturbed clay. 2. The relationship between pore pressure and axial strain of undisturbed clay in normally consolidated state can be expressed as a hyperbolic function like stress-strain relation proposed by Kondner. 3. In the pore pressure-axial strain relation of disturbed clay in normally consolidated state, failure ratio R'f is greatly deviated in the range of 0.7~0.9 proposed by Christian and Desai. 4. For overconsolided clay, when overconsolidation ratio (OCR) is increased, normalized maximum deviator stress is increased and maximum pore pressure is decreased gradually. 5. Cohesion of overconsolidated clay is greater than that of nomally consolidated clay and internal friction angle slightly is decreased. 6. Pore pressure parameter at failure (Af) of overconsolidated clay is varied with OCR, Af becomes negative values with increment in OCR

• Journal of Welding and Joining
• /
• v.2 no.2
• /
• pp.54-61
• /
• 1984

Construction of welding structure is greatly dependent upon welding heat cycle. Fracture toughness is decreased remarkablely due to coarse grained HAZ and inequal residual stress of three dimensions to originate in welding. Post weld heat treatment(PWHT) is carried out to increase the fracture toughness of HAZ and to remove the residual stress. There occur some problem such as toughness decrement and stress relief cracking(SRC) in the coarse grained HAZ subject to the effect of tempering treatment. Therefore, in this paper, the effect of heat inputs affecting cooling rate and PWHT under the no stress on fracture toughness were evaluated by crack opening displacement (COD), SEM and micro-hardness test. Experimental results are as follows; 1. Fracture toughness of weld HAZ is dependent upon weld heat cycle and it is decreased with increment of heat input, but the degree of improvement of fracture toughness after PWHT was linearly increased with heat input. 2. Hardness of the parent metal is not changed, but the softening of coarse grained HAZ is remarkable due to PWHT. 3. Fracture surface of as-weld show the perfect brittle fracture with the cleavage fracture, but after PWHT they appear the ductile fracture surface with dimple.

• Korean Journal of Materials Research
• /
• v.11 no.12
• /
• pp.1009-1013
• /
• 2001

The effects of coupling agent on the interface characteristics between epoxy resin and natural zeolite were studied by SEM, optical microscope and universal testing machine (UTM). Epoxy resin as a matrix was diglycidyl ether of bisphenol A (DGEBA)/4,4'-methylene dianiline (MDA)/malononitrile (MN) system and natural zeolite as an inorganic fillet was produced in Korea. With the increment of zeolite content, tensile strength decreased and it was due to the different elastic moduli of two materials. When external stress was loaded on the composites, the stress concentrated on the weakly bonded interface and crack grew easily. To improve the interface characteristics, the surface of the natural zeolite was treated with the silane coupling agent and it was found that the tensile strength was increased. The morphology of the interface showed that the bonding characteristics were modified by coupling agent.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2000.04a
• /
• pp.211-214
• /
• 2000

Filament wound pressure vessels have been studied for the efficient design tool to consider the variation of fiber angles through-the thickness direction. Filament winding patterns were simulated from semi-geodesic fiber path equation to calculate fiber path on arbitrary surface. Finite element analyses were performed considering fiber angle variation in longitudinal and thickness directions by ABAQUS. For the finite element modeling of the pressure tank, the 3-dimensional layered solid element was utilized. From the stress results of pressure tanks, maximum stress criterion in transverse direction was applied to modify material properties for failed region. In the end of each load increment, resultant layer stresses were compared with a failure criterion and properties were reduced to 1/10 for a failed layer. Results of progressive failure analysis were compared with two experimental data.

• Journal of Welding and Joining
• /
• v.6 no.4
• /
• pp.35-43
• /
• 1988

Welding residual stresses were calculated by two dimensional thermal elasto-plastic analysis using element method. Complicated plastic behavior during heat transfer was simulated with time. Fist, temperature distributions. To consider time varying behavior of material properties and loading and unloading processes, iterative calculation based on initial stiffness method was carried out. The method proposed by Yamata was used in time increment control which determined the accuracy of claculation. comparison with other caculated and experimental results shows fairly good agreement.

• Computers and Concrete
• /
• v.3 no.6
• /
• pp.423-437
• /
• 2006

Stress wave propagation through concrete is simulated by finite element analysis. The concrete medium is modeled as a homogeneous material with smeared properties to investigate and establish the suitable finite element analysis method (explicit versus implicit) and analysis parameters (element size, and solution time increment) also suitable for rigorous investigation. In the next step, finite element analysis model of the medium is developed using a digital image processing technique, which distinguishes the mortar and aggregate phases of concrete. The mortar and aggregate phase topologies are, then, directly mapped to the finite element mesh to form a heterogeneous concrete model. The heterogeneous concrete model is then used to simulate wave propagation. The veracity of the model is demonstrated by evaluating the intrinsic parameters of nondestructive ultrasonic pulse velocity testing of concrete. Quantitative relationships between aggregate size and testing frequency for nondestructive testing are presented.