• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2000.04a
• /
• pp.9-10
• /
• 2000

An important business-field of world-wide steel-industry is the coating of thin metal-sheets with zinc, zinc-aluminum and aluminum based materials. These products mostly go into automotive industry. in particular for the car-body. into building and construction industry as well as household appliances. Due to mass-production, the processing is done in large continuously operating plants where the mostly cold-rolled metal-strip as the substrate is handled in coils up to 40 tons unwind before and rolled up again after passing the processing plant which includes cleaning, annealing, hot-dip galvanizing / aluminizing and chemical treatment. In the liquid Zn, Zn-AI, AI-Zn and AI-Si bathes a combined action of corrosion and wear under high temperature and high stress onto the transfer components (rolls) accounts for major economic losses. Most critical here are the bearing systems of these rolls operating in the liquid system. Rolls in liquid system can not be avoided as they are needed to transfer the steel-strip into and out of the crucible. Since several years, ceramic roller bearings are tested here [1.2], however, in particular due to uncontrollable Slag-impurities within the hot bath [3], slide bearings are still expected to be of a higher potential [4]. The today's state of the art is the application of slide bearings based on Stellite\ulcorneragainst Stellite which is in general a 50-60 wt% Co-matrix with incorporated Cr- and W-carbides and other composites. Indeed Stellite is used as the bearing-material as of it's chemical properties (does not go into solution), the physical properties in particular with poor lubricating properties are not satisfying at all. To increase the Sliding behavior in the bearing system, about 0.15-0.2 wt% of lead has been added into the hot-bath in the past. Due to environmental regulations. this had to be reduced dramatically_ This together with the heavily increasing production rates expressed by increased velocity of the substrate-steel-band up to 200 m/min and increased tractate power up to 10 tons in modern plants. leads to life times of the bearings of a few up to several days only. To improve this situation. the Mechanical Alloying (MA) TeChnique [5.6.7.8] is used to prOduce advanced Stellite-based bearing materials. A lubricating phase is introduced into Stellite-powder-material by MA, the composite-powder-particles are coated by High Energy Milling (HEM) in order to produce bearing-bushes of approximately 12 kg by Sintering, Liquid Phase Sintering (LPS) and Hot Isostatic Pressing (HIP). The chemical and physical behavior of samples as well as the bearing systems in the hot galvanizing / aluminizing plant are discussed. DependenCies like lubricant material and composite, LPS-binder and composite, particle shape and PM-route with respect to achievable density. (temperature--) shock-reSistibility and corrosive-wear behavior will be described. The materials are characterized by particle size analysis (laser diffraction), scanning electron microscopy and X-ray diffraction. corrosive-wear behavior is determined using a special cylinder-in-bush apparatus (CIBA) as well as field-test in real production condition. Part I of this work describes the initial testing phase where different sample materials are produced, characterized, consolidated and tested in the CIBA under a common AI-Zn-system. The results are discussed and the material-system for the large components to be produced for the field test in real production condition is decided. Outlook: Part II of this work will describe the field test in a hot-dip-galvanizing/aluminizing plant of the mechanically alloyed bearing bushes under aluminum-rich liquid metal. Alter testing, the bushes will be characterized and obtained results with respect to wear. expected lifetime, surface roughness and infiltration will be discussed. Part III of this project will describe a second initial testing phase where the won results of part 1+11 will be transferred to the AI-Si system. Part IV of this project will describe the field test in a hot-dip-aluminizing plant of the mechanically alloyed bearing bushes under aluminum liquid metal. After testing. the bushes will be characterized and obtained results with respect to wear. expected lifetime, surface roughness and infiltration will be discussed.

• Reproductive and Developmental Biology
• /
• v.31 no.3
• /
• pp.199-205
• /
• 2007

The present study was carried out to assess the effect of superovulation response and efficiency of embryo production induced with injection of FSH dissolved in polyethylene glycol (PEG) in Hanwoo. Eighty-eight cows were divided into four groups. In group 1, cattle were intramuscularly treated with twice-daily administration of 50mg FSH for 4 days. Group 2 and 3 were subcutaneously single injection of 400mg and 200mg FSH dissolved in 30% PEG, respectively. Group 4 were subcutaneously single injection of 200 mg FSH dissolved in 30% PEG at 7 day after CIDR insertion. The number of corpus luteum (CL) in group 2 resulted in significantly (p<0.05) higher compared to group 1, 3 and 4 (18.5 vs. 11.2, 13.1 and 13.9, respectively). However, the number of total ova $(7.9{\sim}10.4)$, transferable embryos $(3.7{\sim}4.7)$, degenerate embryos $(1.9{\sim}3.5)$ and unfertilized ova $(1.8{\sim}2.7)$ did not differ among treatment groups. No difference was observed in pregnancy rate after transferring the recovered embryos among groups $(36.0{\sim}50.0%)$. In addition, blood progesterone concentrations at embryo recovery did not differ among all groups. In conclusion, although no differences were observed in the number of total ova, transferable embryos and pregnancy rate after transfer, a single injection of reduced dose of FSH (200mg FSH) at 7 day after CIDR insertion is more practical for superovulation treatments than frequent injection because of reduction of stress in Hanwoo and decreases of cost and laber.

• Journal of the Korean GEO-environmental Society
• /
• v.18 no.7
• /
• pp.37-47
• /
• 2017

In this study, a series of full-scale field tests on prebored and precast steel pipe piles and the corresponding numerical analysis have been conducted in order to study the characteristics of pile load-settlement relations and shear stress transfer at the pile-soil interface. Dynamic pile load tests (EOID and restrike) have been performed on the piles and the estimated design pile loads from EOID and restrike tests were analysed. Class-A type numerical analyses conducted prior to the pile loading tests were 56~105%, 65~121% and 38~142% respectively of those obtained from static load tests. In addition, design loads estimated from the restrike tests indicate increases of 12~60% compared to those estimated in the EOID tests. The EOID tests show large end bearing capacity while the restrike tests demonstrate increased skin friction. When impact energy is insufficient during the restrike tests, the end bearing capacity may be underestimated. It has been found that total pile capacity would be reasonably estimated if skin friction from the restrike tests and end bearing capacity from the EOID are combined. The load-settlement relation measured from the static pile load tests and estimated from the numerical modelling is in general agreement until yielding occurs, after which results from the numerical analyses substantially deviated away from those obtained from the static load tests. The measured pile behaviour from the static load tests shows somewhat similar behaviour of perfectly-elastic plastic materials after yielding with a small increase in the pile load, while the numerical analyses demonstrates a gradual increase in the pile load associated with strain hardening approaching ultimate pile load. It has been discussed that the load-settlement relation mainly depends upon the stiffness of the ground, whilst the shear transfer mechanism depends on shear strength parameters.

• Journal of the Korea Concrete Institute
• /
• v.19 no.4
• /
• pp.515-525
• /
• 2007

In this investigation, results of laboratory tests on four reinforced concrete flat plate interior connections with elongated rectangular column support which has been used widely in tall residential buildings are presented. The purpose of this study is to evaluate an effect of column aspect ratio (${\beta}_c={c_1}/{c_2}$=side length ratio of column section in the direction of lateral loading $(c_1)$ to the direction of perpendicular to $c_1$) on the hysteretic behavior under earthquake type loading. The aspect ratio of column section was taken as $0.5{\sim}3\;(c_1/c_2=1/2,\;1/1,\;2/1,\;3/1)$ and the column perimeter was held constant at 1200mm in order to achieve nominal vertical shear strength $(V_c)$ uniformly. Other design parameters such as flexural reinforcement ratio $(\rho)$ of the slab and concrete strength$(f_{ck})$ was kept constant as ${\rho}=1.0%$ and $f_{ck}=40MPa$, respectively. Gravity shear load $(V_g)$ was applied by 30 percent of nominal vertical shear strength $(0.3V_o)$ of the specimen. Experimental observations on punching failure pattern, peak lateral-load and story drift ratio at punching failure, stiffness degradation and energy dissipation in the hysteresis loop, and steel and concrete strain distributions near the column support were examined and discussed in accordance with different column aspect ratio. Eccentric shear stress model of ACI 318-05 was evaluated with experimental results. A fraction of transferring moment by shear and flexure in the design code was analyzed based on the test results.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.47 no.6
• /
• pp.409-412
• /
• 2002

This research was conducted to obtain the fundamental data on salt injury and different responses among cultivars in winter barley (Hordeum vulgare L.). Salts did not affect yield components including number of panicles, stem length, grain number per ear and grain yield while reduced stem dry weight and thousand seed weight significantly with increasing concentrations of salt from 60 to 180 mM. NaCl had less injury effect on barley straw dry weight and thousand seed weight than did $MgSO_4$. Chlorophyll content and relative turgidity in flag leaf were reduced when treated with both salts, while free proline in the salt-treated leaf was increased. Content of proline in salt-treated barley was about 10 folds compared to the control. Based on yield components and physiological traits of flag leaf, the tolerance to salt injury was the greatest in Baegdong, followed by Dongbori#1, Mogpo#55, and Gangbori. The results suggested that salt- stressed barley at reproductive stage had higher free proline content, and that special management in this stage must be considered because salt stress at heading stage affect flag leaf growth as well as yield components Harmfully.

• Journal of the Korean GEO-environmental Society
• /
• v.19 no.4
• /
• pp.5-16
• /
• 2018

In the current study, the engineering behaviour of prebored and precast steel pipe piles was examined from a series of full-scale field measurements by conducting static pile load tests, dynamic pile load tests (EOID and restrike tests) and Class-A and Class-C1 type numerical analysis. The study includes the pile load - settlement relations, allowable pile capacity and shear stress transfer mechanism. Compared to the allowable pile capacity obtained from the static pile load tests, the dynamic pile load tests and the numerical simulation showed surprisingly large variations. Overall among these the restrike tests displayed the best results, however the reliability of the predictions from the numerical analysis was lower than those estimated from the dynamic pile load tests. The allowable pile capacity obtained from the EOID tests and the restrike tests indicated 20.0%-181.0% (avg: 69.3%) and 48.2%-181.1% (avg: 92.1%) of the corresponding measured values from the static pile loading tests, respectively. Furthermore, the computed results from the Class-A type analysis showed the largest scatters (37.1%-210.5%, avg: 121.2%). In the EOID tests, a majority of the external load were carried by the end bearing pile capacity, however, similar skin friction and end bearing capacity in magnitude were mobilised in the restrike tests. The measured end bearing pile capacity from the restrike tests were smaller than was measured from the EOID tests. The present study has revealed that if the impact energy is not sufficient in a restrike test, the end bearing pile capacity most likely will be underestimated. The shear stresses computed from the numerical analysis deviated substantially from the measured pile force distributions. It can be concluded that the engineering behaviour of the pile is heavily affected if a slime layer exists near the pile tip, and that the smaller the stiffness of the slime and the thicker the slime, the greater the settlement of the pile.

• Journal of Applied Tourism Food and Beverage Management and Research
• /
• v.8
• /
• pp.89-121
• /
• 1997

Many of the measures and policies advocated by supply-siders, such as lower taxation, less government intervention, more freedom from restrictive legislation and regulation, and the need for increased productivity can be found in writing the classical economist. Nor is supply-side economics a complete divorcement from Keynesian analysis. In both camps the objectives are the same-high level employment, stable prices and healthy economic growth, the means or suggestions for attaining the objectives, however, differ. Consequently, recommended economic policies and measures are different. keynesians rely primarily on the manipulation of effective demand to increase output and employment and to combat inflation. They assume ample resources to be available in order that supply will respond to demand. The supply-siders emphasize the need to increase savings, investment, productivity and output as a means of increasing income. Supply-siders assume that the increase in income will lead to an increase in effective demand. Keynesians suggest that savings, particularly those not invested, dampen economic activity. Supply-siders hold that savings, or at least an increase in after-tax income, stimulates work effort and provides funds for investment. Perhaps keynesians are guilty of assuming that most savings are not going to be invested, whereas supply-siders may erroneously assume that almost all savings will flow into investment and/ or stimulate work effort. In reality, a middle ground is possible. The supply-siders stress the need to increase supply, but Keynes did not preclude the possibility of increasing economic activity by working through the supply side. According to Keynes' aggregate demand-aggregate supply framework, a decrease in supply will increase output and employment. It must be remembered, however, that Keynes' aggregate supply is really a price. Lowering the price or cost of supply would there by result in higher profit and/ or higher output. This coincides with the viewpoint of supply-siders who want to lower the cost of production via various means for the purpose of increasing supply. Then, too, some of the means, such as tax cuts, tax credits and accelerated depreciation, recommended by suply-siders to increase productivity and output would be favored by Keynesians also as a means of increasing investment, curbing costs, and increasing effective demand. In fact, these very measures were used in the early 1960s in the United State during the years when nagging unemployment was plaguing the economy. Keynesians disagree with the supply-siders' proposals to reduce transfer payments and slow down the process of income redistribution, except in full employment inflationary periods. Keynesians likewise disagree with tax measures that favored business as opposed to individuals and the notion of shifting the base of personal taxation away from income and toward spending. A frequent criticism levied at supply-side economics is that it lacks adequate models and thus far has not been quantified to any great extent. But, it should be remembered that Keynesian economics originally was lacking in models and based on a number of unproved assumptions, such as, the stability of the consumption function with its declining marginal propensity to consume. Just as the economic catastrophe of the great depression of the 1930s paved the way for the application of Keynesian or demand-side policies, perhaps the frustrating and restless conditions of the 1970s and 1980s is an open invitation for the application of supply-side policies. If so, the 1980s and 1990s may prove to be the testing era for the supply-side theories. By the end of 1990s we should have better supply-side models and know much more about the effectiveness of supply-side policies. By that time, also, supply-side thinking may be more crystallized and we will learn whether it is something temporary that will fade away, be widely accepted as the new economics replacing Keynesian demand analysis, or something to be continued but melded or fused with demand management.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.23 no.3
• /
• pp.191-200
• /
• 2017

Proper packaging design can meet both the environmental and economic aspects of packaging materials by reducing the use of packaging materials, waste generation, material costs, and logistics costs. Finite element analysis(FEM) is used as a useful tool in various fields such as structural analysis, heat transfer, fluid motion, and electromagnetic field, but its application in the field of packaging is still insufficient. Therefore, the application of FEM to the field of packaging can save the cost and time in the future research because it is possible to design the package by computer simulation, and it is possible to reduce the packaging waste and logistics cost through proper packaging design. Therefore, this study investigated the FEM papers published in Korea for the purpose of helping research design using FEM program in the field of packaging in the future. In this paper, we analyzed the 29 papers that were directly related to the analysis of FEM papers published in domestic journals from 1991 to 2017. As a result, we analyzed the research topic, FEM program, and analysis method using each paper, and presented the direction that can be applied in future packaging field. When the FEM is applied to the packaging field, it is possible to change the structure and reduce the thickness through the stress and vibration analysis applied to the packaging material, thereby reducing the cost by improving the mechanical strength and reducing the amount of the packaging material. Therefore, in the field of packaging research in the future, if the FEM is performed together, economical and reasonable packaging design will be possible.

• Proceedings of the Korean Society of Crop Science Conference
• /
• 2017.06a
• /
• pp.252-252
• /
• 2017

Nowadays water shortage is becoming one of the biggest problems in the Korea. Many different methods are developed for conservation of water. Soil water management has become the most indispensable factor for augmenting the crop productivity especially on soybean (Glycine max L.) because of their high susceptibility to both water stress and water logging at various growth stages. The farmers have been using irrigation techniques through manual control which farmers irrigate lands at regular intervals. Automatic irrigation systems are convenient, especially for those who need to travel. If automatic irrigation systems are installed and programmed properly, they can even save you money and help in water conservation. Automatic irrigation systems can be programmed to provide automatic irrigation to the plants which helps in saving money and water and to discharge more precise amounts of water in a targeted area, which promotes water conservation. The objective of this study was to determine the possible effect of automatic irrigation systems based on soil moisture on soybean growth. This experiment was conducted on an upland field with sandy loam soils in Department of Southern Area Crop, NICS, RDA. The study had three different irrigation methods; sprinkle irrigation (SI), surface drip irrigation (SDI) and fountain irrigation (FI). SI was installed at spacing of $7{\times}7m$ and $1.8m^3/hr$ as square for per irrigation plot, a lateral pipe of SDI was laid down to 1.2 m row spacing with $2.3L\;h^{-1}$ discharge rate, the distance between laterals was 20 cm spacing between drippers and FI was laid down in 3m interval as square for per irrigation plot. Soybean (Daewon) cultivar was sown in the June $20^{th}$, 2016, planted in 2 rows of apart in 1.2 m wide rows and distance between hills was 20 cm. All agronomic practices were done as the recommended cultivation. This automatic irrigation system had valves to turn irrigation on/off easily by automated controller, solenoids and moisture sensor which were set the reference level as available soil moisture levels of 30% at 10cm depth. The efficiency of applied irrigation was obtained by dividing the total water stored in the effective root zone to the applied irrigation water. Results showed that seasonal applied irrigation water amounts were $60.4ton\;10a^{-1}$ (SI), $47.3ton\;10a^{-1}$ (SDI) and $92.6 ton\;10a^{-1}$ (FI), respectively. The most significant advantage of SDI system was that water was supplied near the root zone of plants drip by drip. This system saved a large quantity of water by 27.5% and 95.6% compared to SI, FI system. The average soybean yield was significantly affected by different irrigation methods. The soybean yield by different irrigation methods were $309.7kg\;10a^{-1}$ from SDI $282.2kg\;10a^{-1}$ from SI, $289.4kg\;10a^{-1}$ from FI, and $206.3kg\;10a^{-1}$ from control, respectively. SDI resulted in increase of soybean yield by 50.1%, 7.0% 9.8% compared to non-irrigation (control), FI and SI, respectively. Therefore, the automatic irrigation system supplied water only when the soil moisture in the soil went below the reference. Due to the direct transfer of water to the roots water conservation took place and also helped to maintain the moisture to soil ratio at the root zone constant. Thus the system is efficient and compatible to changing environment. The automatic irrigation system provides with several benefits and can operate with less manpower. In conclusion, improving automatic irrigation system can contribute greatly to reducing production costs of crops and making the industry more competitive and sustainable.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.62 no.2
• /
• pp.87-95
• /
• 2017

The increase in the frequency of occurrence of abnormal weather could include severe rainfall, which could cause rice submergence during the ripening stage. This experiment was conducted to clarify the effects of submergence during the ripening period on yield and quality of rice. The flooding treatment was conducted at 7 and 14 days after heading. Flooding conditions were created with two conditions, flag leaf exposed and overhead flooding, and each condition was divided into two conditions according to water quality-clear and muddy. Although the yield decrease was more severe at 7 days after heading because of the decrease in the ripening ratio, the head rice ratio was more affected at 14 days after heading because of the increase in the chalky kernel ratio. The maximum quantum yield (Fv/Fm), which indicates the photosynthetic efficiency, did not differ before and after the flooding treatment until flooding continued for 4 days. In addition, stem elongation occurred because of flooding as an avoidance mechanism in japonica rice. This phenomenon was expected to decrease the supply of assimilation products to the spikelet (sink). Overall, it was suggested that additional experiments should be conducted examining the change in the starch synthesis mechanism and transfer of assimilate products resulting from submergence, for development of cultivation techniques corresponding to submergence and breeding of varieties with submergence tolerance characteristics.