• 한국세라믹학회지
• /
• 제41권1호
• /
• pp.69-75
• /
• 2004

인공치아용 3Y-TZP와 (Y,Nb)-TZP/$Al_2O_3$ 복합체를 유사 구강분위기인 인공타액 하에서 500-3000N의 하중 조건으로 $10^6$ 횟수까지 헤르찌안 반복하중 피로특성을 조사하였다. 500N의 하중에서 $5{\times}10^5$까지 반복피로 실험결과, 강도 저하 및 균열 현상은 관찰되지 않았다. 피로특성은 SY-TZP가 (T,Nb)-TZP/$Al_2O_3$ 복합체보다 상전이에 의한 응역회복 때문에 우수하였다. 하중값이 증가함에 따라 링 균열에서 방사상 균열로 전이되었을 때 급격한 강도 저하 현상이 발생하였다. 강도 저하 현상은 유사 구강 분위기하에서 반복 하중 접촉 시 발생한 균열을 통해 침투한 인공타액의 화학적 침식으로 더욱 가속화 되었다.

• Structural Engineering and Mechanics
• /
• 제66권1호
• /
• pp.45-59
• /
• 2018

The bi-material elastic system consisting of the pre-stressed hollow cylinder and pre-stresses surrounding infinite elastic medium is considered and it is assumed that the mentioned initial stresses in this system are caused with the compressing or stretching uniformly distributed normal forces acting at infinity in the direction which is parallel to the cylinder's axis. Moreover, it is assumed that on the internal surface of the cylinder the ring load which moves with constant velocity acts and within these frameworks it is required to determine the influence of the aforementioned initial stresses on the critical velocity of the moving load. The corresponding investigations are carried out within the framework of the so-called three-dimensional linearized theory of elastic waves in initially stresses bodies and the axisymmetric stress-strain state case is considered. The "moving coordinate system" method is used and the Fourier transform is employed for solution to the formulated mathematical problem and Fourier transformation of the sought values are determined analytically. However, the originals of those are determined numerically with the use of the Sommerfeld contour method. The critical velocity is determined from the criterion, according to which, the magnitudes of the absolute values of the stresses and displacements caused with the moving load approaches an infinity. Numerical results on the influence of the initial stresses on the critical velocity and interface normal and shear stresses are presented and discussed. In particular, it is established that the initial stretching (compressing) of the constituents of the system under consideration causes a decrease (an increase) in the values of the critical velocity.

• 대한인간공학회지
• /
• 제27권3호
• /
• pp.1-6
• /
• 2008

Individual finger/total grip forces, and subjective preferences for various individual finger grip spans (i.e., four fingers had identical grip spans or different grip spans) were evaluated by using an "Adjustable Multi-Finger Force Measurement (MFFM) System". In this study, three grip spans were defined as follows: a 'favorite grip span' which is the span with the highest subjective preference; a 'maximum grip span' which is the span with the highest total grip force; a 'maximum finger grip span' which is a set of four grip spans that had maximum finger grip forces associated with the index, middle, ring, and little fingers, respectively. Ten males were recruited from university population for this study. In experiment I, each participant tested the maximum grip force with five grip spans (45 to 65mm) to investigate grip forces and subjective preferences for three types of grip spans. Results showed that subjective preferences for grip spans were not coincidence with the performance of total grip forces. It was noted that the 'favorite grip span' represented the lowest total grip force, whereas the 'maximum finger grip span' showed the lowest subjective preferences. The individual finger forces and the average percentage contribution to the total finger force were also investigated in this study. The findings of this study might be valuable information for designing ergonomics hand-tools to reduce finger/hand stress as well as to improve tool users' preferences and performance.

• 대한기계학회논문집A
• /
• 제35권2호
• /
• pp.169-174
• /
• 2011

제 1 급 와동이 모사된 비관통형 치아 시편에 수복된 복합레진의 중합 수축시 발생하는 AE 신호를 실시간으로 검출한 후 이를 분석하였다. 시간대별 발생 분포를 살펴보면, 광조사 초기에 중합 수축이 급격히 진행되는 제 I 구간에서 AE event 가 많이 관찰되었다. 제 I구간 후 AE event 발생 빈도가 낮아져 AE 가 별로 관찰되지 않은 제II구간이 있었는데, AE 신호의 발생이 적은 PMMA 는 치아에 비해 구간이 길었으며 AE 검출이 잦았던 스테인리스스틸 모형은 제 II 구간이 짧았다. AE 활성도를 나타내는 구간 특성은 수복재와 와동의 계면부에서 일어나는 균열의 발생빈도를 나타내는 것으로 사료되며 젤화점 직후의 제I 구간에서 AE 가 집중적으로 관측되는 바, 수복재와 와동 사이의 갭 형성은 바로 젤화점 직후에 만들어졌음을 가리킨다. 신호의 최대 진폭은 25-45dB 이었고 1 차 중심 주파수는 100-200kHz 와 240-400kHz 영역의 신호들이 발생하였으며 이는 레진이나 접착층의 파괴에 해당하였다.

• 한국전산구조공학회논문집
• /
• 제33권6호
• /
• pp.391-399
• /
• 2020

본 연구는 유한요소 해석모델을 이용해 아치 형상을 갖는 석션 상판의 거동을 분석하였다. 평판형 및 아치형 상판의 기본적인 구조성능에 대해 비교함으로써 아치형 상판의 이점을 설명하였다. 또한 아치형 상판의 기하 및 보강재 배치 변화에 따른 거동 변화를 비교하여 각 인자가 상판의 응력 및 변형에 미치는 영향을 조사하였다. 추가로 아치형 상판 가장자리의 경계조건 영향을 수치적으로 분석함으로써, 아치형 상판의 보강재 배치와 가물막이 벽체와의 상호거동 영향을 규명하고 이를 통해 보강형 아치형 상판의 구조설계의 기본 개념을 도출하였다. 평판형 상판과 달리 환형 보강재가 아치형 상판의 구조 거동을 확연히 개선시킬 수 있음을 확인하였으며, 방사 보강재의 역할은 상판 가장자리의 구속상태에 의존적이었다.

• Earthquakes and Structures
• /
• 제22권6호
• /
• pp.539-548
• /
• 2022

Steel plate shear walls (SPSWs) are one of the most important and widely used lateral load-bearing systems. The reason for this is easier execution than reinforced concrete (RC) shear walls, faster construction time, and lower final weight of the structure. However, the main drawback of SPSWs is premature buckling in low drift ratios, which affects the energy absorption capacity and global performance of the system. To address this problem, two groups of SPSWs under cyclic loading were investigated using the finite element method (FEM). In the first group, several series of circular rings have been used and in the second group, a new type of SPSW with concentric circular rings (CCRs) has been introduced. Numerous parameters include in yield stress of steel plate wall materials, steel panel thickness, and ring width were considered in nonlinear static analysis. At first, a three-dimensional (3D) numerical model was validated using three sets of laboratory SPSWs and the difference in results between numerical models and experimental specimens was less than 5% in all cases. The results of numerical models revealed that the full SPSW undergoes shear buckling at a drift ratio of 0.2% and its hysteresis behavior has a pinching in the middle part of load-drift ratio curve. Whereas, in the two categories of proposed SPSWs, the hysteresis behavior is complete and stable, and in most cases no capacity degradation of up to 6% drift ratio has been observed. Also, in most numerical models, the tangential stiffness remains almost constant in each cycle. Finally, for the innovative SPSW, a relationship was suggested to determine the shear capacity of the proposed steel wall relative to the wall slenderness coefficient.

• Composites Research
• /
• 제21권3호
• /
• pp.9-17
• /
• 2008

본 논문에서는 저속충격하중을 받은 필라멘트 와인딩 탄소섬유강화 복합재 압력용기의 잔류강도 저하특성에 대한 수치해석 및 실험결과에 대해서 논한다. 복합재 압력용기의 원통부의 여러 곳에 대해 낙하 공구의 끝단을 모사한 삼각형 충격자를 사용한 저속 충격시험이 실시되었고, 유한요소해석을 수행하여 충격시의 기계적 변형 및 응력분포 거동에 대한 예측을 실시하였다. 충격하중을 받은 복합재 압력용기의 잔류강도 저하 특성을 정량적으로 평가하기 위해, 충격부위를 포함하는 원환시편을 압력용기의 실린더부로부터 채취하여, 원주방향 내압인장강도 측정 수압시험법으로부터, 원환시편의 수압파열 압력을 측정하였다. 결과적으로 본 연구를 통해 충격 에너지의 수준에 따른 잔류강도 변화가 성공적으로 계측되었으며, 복합재 압력용기의 충격손상허용을 정량적으로 평가하기 위한 유용한 방법론이 정립되었다.

• Parasites, Hosts and Diseases
• /
• 제61권2호
• /
• pp.154-162
• /
• 2023

Glucose-6-phosphate dehydrogenase (G6PD) deficiency is caused by X-linked recessive disorderliness. It induces severe anemia when a patient with G6PD deficiency is exposed to oxidative stress that occurs with administration of an antimalarial drug, primaquine. The distribution of G6PD deficiency remains unknown while primaquine has been used for malaria treatment in Myanmar. This study aimed to investigate the prevalence of G6PD deficiency and its variants in Chin State, Myanmar. Among 322 participants, 18 (11 males and 7 females) demonstrated a G6PD deficiency. Orissa variant was dominant in the molecular analysis. This would be related to neighboring Indian and Bangladeshi population, in which Orissa variant was also reported as the main mutation type. The screening test for G6PD deficiency before primaquine treatment appears to be important in Myanmar.

• Advances in nano research
• /
• 제15권6호
• /
• pp.495-511
• /
• 2023

In this research, the impact of micro-silica, nano-silica, and polypropylene fibers on the fracture energy of self-compacting concrete was thoroughly examined. Enhancing the fracture energy is very important to increase the crack propagation resistance. The study focused on evaluating the self-compacting properties of the concrete through various tests, including J-ring, V-funnel, slump flow, and T50 tests. Additionally, the mechanical properties of the concrete, such as compressive and tensile strengths, modulus of elasticity, and fracture parameters were investigated on hardened specimens after 28 days. The results demonstrated that the incorporation of micro-silica and nano-silica not only decreased the rheological aspects of self-compacting concrete but also significantly enhanced its mechanical properties, particularly the compressive strength. On the other hand, the inclusion of polypropylene fibers had a positive impact on fracture parameters, tensile strength, and flexural strength of the specimens. Utilizing the response surface method, the relationship between micro-silica, nano-silica, and fibers was established. The optimal combination for achieving the highest compressive strength was found to be 5% micro-silica, 0.75% nano-silica, and 0.1% fibers. Furthermore, for obtaining the best mixture with superior tensile strength, flexural strength, modulus of elasticity, and fracture energy, the ideal proportion was determined as 5% micro-silica, 0.75% nano-silica, and 0.15% fibers. Compared to the control mixture, the aforementioned parameters showed significant improvements of 26.3%, 30.3%, 34.3%, and 34.3%, respectively. In order to accurately model the tensile cracking of concrete, the authors used softening curves derived from an inverse algorithm proposed by them. This method allowed for a precise and detailed analysis of the concrete under tensile stress. This study explores the effects of micro-silica, nano-silica, and polypropylene fibers on self-compacting concrete and shows their influences on the fracture energy and various mechanical properties of the concrete. The results offer valuable insights for optimizing the concrete mix to achieve desired strength and performance characteristics.

• 폴리머
• /
• 제27권3호
• /
• pp.210-216
• /
• 2003

Benzylquinoxalinium hexafluoroantimonate를 함유한 4-vinyl-1-cyclohexene diepoxide (VCE)/diglycidyl ether of bisphenol-A (DGEBA) 에폭시 블렌드를 전자선을 사용하여 경화하였다. 그리고 VCE에서 DGEBA의 함량이 경화 거동, 열적 그리고 기계적 특성에 미치는 영향을 연구하였다. VCE/DGEBA 블렌드계의 조성은 100 : 0, 80 : 20, 60 : 40, 40 : 60, 20 : 80, 및 0 : 100 wt%로 하였다. 경화 거동과 열안정성은 근적기선 분광기와 열중량 분석기로 각각 측정하였다. 또한 기계적 계면 특성을 연구하기 위하여 경화된 시편의 임계응력 세기인자 ( $K_{IC}$) 실험을 수행하였다. 그 결과 DGEBA 함량 증가와 함께 수산화기와 카보닐기에 기인한 짧은 곁사슬 구조와 사슬 절단의 감소가 근적외선 분광법에 의해서 측정되었다. 그리고 열안정성 인자들로서 초기 열분해 온도 (IDT), 최대 무게 감량시 온도 ( $T_{max}$), 그리고 분해 활성화 에너지 ( $E_{d}$)는 DGEBA 함량 증가와 함께 증가하였다. 이러한 결과들은 DGEBA 함량 증가에 따른 점도의 감소와 안정된 방향족 고리 구조, 그리고 graftedIPN구조로 설명될 수 있었다. 또한 최대 $K_{IC}$ 값은 40 : 60 wt%에서 보였다.보였다..