• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.10
• /
• pp.1053-1060
• /
• 2011

This study is performed to determine the drug concentration profiles of drug-eluting stents (DES) for an ideal circular ring stent and intertwined stent models for various Reynolds numbers (Re = 200, 400, and 800). The Navier.Stokes equations coupled with the advection-diffusion equation are solved numerically in order to determine how the flow patterns and drug deposition are affected in the in-stent and post-stent regions where flow separation and recirculation occur. The presence of DES within the arterial segment affects the local drug distribution in the flow field. As a result, the drug concentration for the intertwined stent is higher over the in-stent region in comparison with the ideal stents. For a given stent geometry, the local drug concentration in the in-stent region decreases with Reynolds number, while for a given Reynolds number, the local drug concentration is relatively insensitive to the stent geometry. The results show that drug concentration along the arterial wall is significantly higher within the in-stent and post-stent regions for the intertwined stent geometry than for the ideal stent geometries.

• Journal of the Korean Wood Science and Technology
• /
• v.21 no.2
• /
• pp.39-48
• /
• 1993

End-matched disks of 7.7cm thickness were part-time dried in vacuum press dryer to investigate the drying characteristics by using drying schedules and end treatments. The ginkgo disks could be dried faster with severer end checks and ring failures by C schedule than by S schedule. There were no significant differences in drying rates and amounts of end checks, ring failures and V-shaped checks occurred between ginkgo disks end-taped with Korean traditional paper (KTP) and those untreated. The drying time of walnut disks was slightly reduced by end-taping with KTP. And the length of end checks and V-shaped checks and the frequency of defected disk were decreased more effectively than those untreated. The tangential strains and tangential drying stresses near bark sides of ginkgo and walnut disk untreated were developed in the early stage of drying and incresed slightly curvi-linearly above fiber saturation point (fsp) and more curvi-linearly below fsp. The influence of end-taping with KTP on the drying rate for impermeable walnut disk was stronger than that for permeable ginkgo disk.

• Geomechanics and Engineering
• /
• v.29 no.3
• /
• pp.281-290
• /
• 2022

The direct shear test is commonly used to evaluate the shear behavior of frozen soil-structure interfaces under normal stress. However, failure criteria, such as the Mohr-Coulomb failure criterion, are needed to obtain the unconfined shear strength. Hence, the punch shear test, which is usually used to estimate the shear strength of rocks without confinement, was examined in this study to directly determine the adfreezing strength. It is measured as the shear strength of the frozen soil-structure interface under unconfined conditions. Different soils of silica sand, field sand, and field clay were prepared inside the steel and concrete ring structures. Soil and ring structures were frozen at the target temperature for more than 24 h. A punch shear test was then conducted. The test results show that the adfreezing strength increased with a decrease in the target temperature and increase in the initial water content, owing to the increase in ice content. The adfreezing strength of field clay was the smallest when compared with the other soil specimens because of the large amount of unfrozen water content. The field sand with the larger normalized roughness showed greater adfreezing strength than the silica sand with a lower normalized roughness. From the experiment and analysis, the applicability of the punch shear test was examined to measure the adfreezing strength of the frozen soil-structure interface. To find a proper sample dimension, supplementary experiments or numerical analysis will be needed in further research.

• Nuclear Engineering and Technology
• /
• v.56 no.1
• /
• pp.195-206
• /
• 2024

Shenzhen Innovation Light source Facility (SILF) is a 3.0 GeV fourth generation diffraction limited synchrotron light source currently under construction in Shenzhen. The SILF storage ring is proposed to use two 500 MHz single cell superconducting radio frequency (SRF) cavities to provide 2.4 MV RF voltage. In this study, we examined the geometric structure of mature CESR superconducting cavities and adopted a beam-pipe-type extraction scheme for high-order modes (HOM). One of the objectives of SRF cavity design and optimization in this study is to reduce E_p/E_acc and B_p/E_acc as much as possible to reduce power loss and ensure stable operation of the cavity. To reduce the risk of beam instability and thermal breakdown, the HOM and Multipacting (MP) are simulated. Moreover, the mechanical properties of the cavity are analyzed, including frequency sensitivity from pressure of liquid helium (LHe), stress, tuning, Lorentz force detuning (LFD), the microphone effect, and buckling. By comprehensive design and optimization of 500 MHz single-cell SRF cavities, a superconducting cavity for SILF storage ring was developed. This paper will detailed present the design and simulation.

• Journal of the Korean Wood Science and Technology
• /
• v.45 no.1
• /
• pp.43-52
• /
• 2017

This study was fulfilled to verify the durations of cambial activity and analyze the associations of degree days and precipitation with the initiation of cambial activity and intra-annual wood formation for Pinus koraiensis and Chamaecyparis pisifera planted at Mt. Worak, respectively, by monitoring of their intra-annual cambial activities. And more, the reason was also analyzed why the DBH of Chamaecyparis pisifera known as planted in the same year could be classified as two groups (CPL: ${\phi}30cm$, CPS: ${\phi}15cm$). The intra-annual cambial activity was monitored using mini-cores (${\phi}2mm$) and they were collected in 2-week interval between April and October. However, between April and May and between middle September and October expected as the initiation and cessation of the cambial activity, respectively, it was fulfilled in 1-week interval. The average number of tree rings for PK (30) was less than CPS (37) and CPL (38), whereas the average ring width of PK (4.12 mm) was wider than CPS (1.84 mm) and CPL (3.97 mm). In the comparison of ring widths between CPL and CPS, CPL was 2.13 mm wider than CPS, however, excepting CPS 1 (0.83 mm), the average ring widths of CPS 2 (2.42 mm) and CPS 3 (2.73 mm) in the last 3 years were close to the average of CPL (2.71 mm). The initiation of cambial activity for PK was between 1 and 21 April, which was 1 week earlier than CPL and CPS (excepting CPS 1) and the cessation was between 1 and 22 September. The longest growing season therefore was 157.3 days (${\pm}3.3$) and it was longer than CPL ($145.7{\pm}6.6days$) and CPS ($148.0{\pm}15.1days$). In CP groups there were wide variations for the cessation of cambial activity and also there were the meaningful linear relationship between the growing seasons and the ring widths (r = 0.69, p < 0.064). The cambial activity in PK was initiated when degree days were between 99 and 134 and in CPS (excepting PCS 1) and CPL between 134 and 200. Excepting CPS 3, the false ring was observed in all samples collected on 21 July when drought stress was high due to low precipitation from June to the beginning of July.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.32 no.5A
• /
• pp.307-315
• /
• 2012

Recently, ultra high performance fiber reinforced concrete (UHPFRC) having over 180 MPa compressive strength and 10 MPa tensile strength has been developed in Korea. However, UHPFRC represents different material properties with normal concrete (NC) and conventional high performance concrete (HPC) such as a high early age autogenous shrinkage and a rapid dry on the surface, because it has a low water-binder ratio and high fineness admixtures without coarse aggregate. In this study, therefore, to propose suitable experimental methods and regulations, and to evaluate mechanical properties at a very early age for UHPFRC, setting, shrinkage and tensile tests were performed. From the setting test results, paraffin oil was an appropriate material to prevent drying effect on the surface, because if paraffin oil is applied on the surface, it can efficiently prevent the drying effect and does not disturb or catalyze the hydration of cement. From the ring-test results, it was defined that the shrinkage stress is generated at the time when the graph tendency of temperature and strain of inner steel ring is changed. By comparing with setting test result, the shrinkage stress was firstly occurred as the penetration resistance of 1.5 MPa was obtained, and it was about 0.6 and 2.1 hour faster than those of initial and final sets. So, the starting time of autogenous shrinkage measurement (time-zero) of UHPFRC was determined when the penetration resistance of 1.5 MPa was obtained. Finally, the tensile strength and elastic modulus of UHPFRC were measured from near initial setting time by using a very early age tensile test apparatus, and the prediction models for tensile strength and elastic modulus were proposed.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.6
• /
• pp.655-662
• /
• 2014

This study conducted tensile tests on an Alloy 690TT tube at room temperature (RT) and at $343^{\circ}C$ using tube- and ring-type specimens to investigate the stress-strain behavior and tensile properties of a steam generator (SG) tube in the axial and circumferential directions at RT and at the design temperature of a nuclear power plant (NPP). The results of the axial tensile test showed that yield point phenomena appeared at both RT and $343^{\circ}C$, and serrated flow in the stress-strain curve appeared at $343^{\circ}C$. Yield and tensile strengths for both directions were clearly lower at $343^{\circ}C$ compared to RT; however, the elongations were approximately the same at both test temperatures. Regardless of the test temperature, the strengths in the circumferential direction were lower by approximately 5~10 % than those in the axial direction. In addition, the test data revealed that the reduction in the yield and tensile strengths of the Alloy 690TT SG tube with the test temperature was more significant than that estimated by the temperature correction factor of ASME Sec.II.

• Composites Research
• /
• v.33 no.3
• /
• pp.125-132
• /
• 2020

The polymerization shrinkage behavior of dimethacrylate-based composite (Clearfil AP-X, Kuraray) and silorane-based composite (Filtek P90, 3M ESPE) used for dental composite restorations was measured using digital image correlation method. The stress distribution on the surface of specimen was calculated by finite element analysis with equivalent elastic modulus and was compared with the measured shrinkage distribution. Camera images were monitored by a CCD camera during and after the irradiation of light. As a result of the DIC analysis, a non-uniform shrinkage distribution was observed in both composite resins, and the resin core inside the ring specimen had free flowability, leading to in greater shrinkage strain than the resin/ring interfacial region. It was observed that as the distance from the center of the resin increased, the radial average shrinkage strain decreased. The radial average shrinkage strain during light irradiation occurred to be 33% for P90 and 57% for AP-X of the entire strain at the end of the test. The shrinkage behavior of P90 and AP-X was measured to be significantly different from each other during light irradiation. In the resin near the resin/ring interface, it was confirmed that the tensile strain rapidly formed to increase after light irradiation, causing a tensile stressed, interface weak.

• Journal of the Korean Wood Science and Technology
• /
• v.29 no.3
• /
• pp.14-20
• /
• 2001

On the bending process, metal-strap plays an important role in dispersing the stress generated in wood. Therefore, the metal-strap has more influence on the property of bentwood materials. The effect of the metal-strap thickness for bentwood was examined. The effect of metal-strap on the bending properties of Korean red pine(Pinus densiflora Sieb. et Zucc.)was investigated in this research. The metal-strap thickness is divided into 4 kinds such as 1.0, 0.8, 0.6, 0.4 mm. The specimens were selected by grain such as annual ring angles, flat grain and half-edge grain specimens. As a result of this study, the bending ability of 1.0, 0.8 mm, thickness of half-edge grain specimens was better than flat grain specimens but the result of 0.6, 0.4 mm were reversed. The bending ability of half-edge grain was better than flat grain and the grade was higher. When the processed specimens were dried, the radius of curvature(ROC) was decreased became drying-stress was not perfectly dispersed. An optimum drying-condition would deminish this phenomenon.

• Composites Research
• /
• v.22 no.4
• /
• pp.33-40
• /
• 2009

Fiber orientation effects on the impact surface fracture of the glass plates coated with the glass fiber/epoxy lamina layer were investigated using a small-diameter steel-ball impact experiment. Four kinds of materials were used: soda-lime glass plates, unidirectional glass fiber/epoxy layer(one ply, two plies)-coated, crossed glass tiber/epoxy layer (two plies)-coated glass plates. The maximum stress and absorbed fracture energy were measured on the back surface of glass plates during the impact. With increasing impact velocity, various surface cracks such as ring, cone, radial and lateral cracks appeared near the impacted site of glass plates. Cracks in the plate drastically diminished by glass fiber coating. The tiber orientation guided the directions of delamination and plastic deformation zones between the tiber layer and the glass plate. Impact surface-fracture indices expressed in terms of the maximum stress and absorbed energy could be used as an effective evaluation parameter of the surface resistance.