• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.1038-1041
• /
• 2004

In this study, developed a micro-level experimental setup to measure pore pressure and poroelastic modulus in various strain and strain rate about a stress in micro-structure of bone tissue. It is essential device in the development of the model to analysis the interstitial bone fluid flow of the lacuno-canalicular system to be known that would effect on the bone remodeling. The constitution of the experimental setup is as follows, microscopic image processing system; actuator control unit; load measurement system. A pilot study was used an artificial chemical wood to have similar poroelastic property of bone matrix and conducted to validate the suitability of the measurement system.

• 대한기계학회논문집
• /
• 제16권7호
• /
• pp.1373-1380
• /
• 1992

본 연구에서는 전보에서 실험역학적으로 도출한 .DELTA.A가 재료 및 하중크기에 의존하는 점에 착안하여, SNC631-A, SNC631-B, S45C, A12024-T3 및 A17075-T6 등 5종 류 재료를 응력비 R=0.1, 0.3, 0.5에서 피로크랙전파속도시험을 실시하고, 피로크랙팁 의 국소피로변형률장의 상태를 정량적으로 나타낼 수 있는 피로변형률확대계수 .DELTA.A(m, P)를 이용하여 크랙전파속도 da/dN을 통일적으로 평가하고, 그 결과의 유용성을 명백 히 하였다.

• 대한치과보철학회지
• /
• 제37권1호
• /
• pp.93-103
• /
• 1999

Stress distribution on mandibular implants supporting overdentures were registered in vitro experimental model by means of 4 rosette gauges which were placed around the implant. The overdenture attachments used in this study were the Resilient Dolder bar, Rigid Bolder bar, Round bar, Hader bar & Dal-Ro attachment. An occlusal jig was placed on the overdenture and the loading sites were 3 points which mimicked working, balancing, and median relations. With 5 and 10kg loading, strains were measured by strain indicator(P-3500, Measurement group, Raleigh, USA), and using these data, maximum and minimum principal stresses and Von Mises stress were calculated and evaluated. The results were as follows : There was a tendency of high stress concentration in the lingual side of the implant, and in the buccal side low stress was developed regardless of the attachment systems. The resilient Bolder bar concentrated highest stress among the attachment systems, and the Round bar and the Dal-Ro attachment provided comparatively low stresses around the implant. The rigid Bolder bar concentrated high stress in the mesial side, and the Dal-Ro attachment developed tensile stress patterns in the lingual and distal sides of the implant at the balancing relation.

• 한국농공학회지
• /
• 제34권1호
• /
• pp.41-48
• /
• 1992

Various soil behaviors usually occurring in the geotechnical problems, such as, cutting and embankments, stability of slope, seepage, consolidations, shearing failures and liquefaction, should be predicted and analyzed in any way. An approach of these predictions may be followed by the development of the constitutive equations as first and subsequently solved by numerical methods. The purpose of this paper is develop the constitutive equation of sands uder monotonic or cyclic loadings. The constitutive equation which is based on elasto-plastic theory, modified anisotropic consolidated stress parameter by Sekiguchi et al and Pender's theory is derived. And the equation is included a new stress parameter, hardening function, Bauschinger's effects and Pender's theory. The model is later evaluated and confirmed the validity by the test data of Ottawa sand, Banwol sand Hongseong sand. The following conclustions may be drawn: 1. The consititutive equation which is based on elasto-plastic theory, modified anisotropic consolidated stress parpameter by Sekiguchi et al and Pender's theory is derived. The equation in included a new stress parameter, hardening function, Bauschinger's effect and Pender's theory. 2. For Ottawa sand, the result of the constitutive equation shows a better agreement than that of Oka et al. The result of axial strain agrees well with the tested data. However, the result of horizontal strain is little bit off for the cyclic loadings or large stress. It is thought that the deviation may be improved by considering Poisson's ratio and precise measurement of shear modulus. 3. Banwol sand is used for the strain and stress tests with different relative densitites and confining pressures. The predeicted result shows a good agreement with the tested data because the required material parameters were directly measurd and determined form this laboratory. 4. For Hongseong sand, the tests under same amplitude of cyclic deviatoric stress shows a similar result with the tested data in absolute strain. It shows the acute shape of turning point because the sine wave of input is used in the test but the serrated wave in prediction.

• 한국재료학회지
• /
• 제4권5호
• /
• pp.502-509
• /
• 1994

dynamic strain gage와 12bit AD(analog to digital converter)를 이용한 새로운 제진특성 측정 장치를 제작하였다. 이 장치를 이용하여 일반재료와 고제진재료의 제진특성을 연구하였다. 또한 열처리 조건, 초기 진동 진폭, 그리고 내부응력의 변화에 따른 SDC(specific damping capacity)변화에 관하여 연구하였다. 일반재료와 제진재료의 비교에서, 제진재료는 진동을 가한 후 0.4초 이내에 진동 진폭이 거의 사라졌지만, 같은 시간에 일반재료의 진동 진폭은 거의 감소하지 않았다. Fe-16wt. %Cr계 합금의 제진 특성은 노냉일 때 SDC max 가 40%이상이었고, Fe-5.5wt.%Ai합금의 제진 특성은 공냉일 때 SDC max값이 30%이상이었다. 초기 진동 진폭이 증가할수록 최대 제진 특성치는 낮은 진동 진폭 영역으로 이동하였다. 제진 특성은 내부 응력이 증가할수록 급격한 감소를 보였으며, 본 연구에서 개발한 제진측정 장치는 낮은 진동 진폭의 영역에서 정확한 제진 특성 측정이 가능하였다.

• 한국초전도ㆍ저온공학회논문지
• /
• 제15권2호
• /
• pp.29-33
• /
• 2013

The understanding of the strain dependence of critical current, $I_c$, in the reversible region is important for the evaluation of the performance of coated conductor (CC) tapes in practical applications. In this study, the stress/strain tolerance of $I_c$ in GdBCO CC tapes with stainless steel substrate stabilized by additional Cu and brass laminate was analyzed quantitatively through $I_c$-strain measurement at 77 K under self-field. The variation in irreversible strain limits of CC tapes by the addition of stabilizing layers was analyzed through the consideration of the pre-strain induced on the GdBCO coating film. The results were then compared with the ones previously reported for GdBCO CC tapes with Hastelloy substrate. As a result, GdBCO CC tapes with stainless steel substrate showed much higher strain tolerance of $I_c$ as compared with those adopting Hastelloy substrate.

• 한국지반환경공학회 논문집
• /
• 제6권1호
• /
• pp.45-51
• /
• 2005

말뚝을 설계함에 있어 극한지지력을 산정하는 것만으로는 말뚝의 장기 거동에 있어서의 하중분포를 고려할 수 없으므로 재하시험시 변형률계나 응력계를 사용하여 말뚝의 하중 재하에 따른 주면저항(the shaft resistance)의 분포를 측정하고 있다. 그러나 대부분의 재하시험시 하중이 '0'일 때를 'zero time'으로 하여 계측기의 값을 읽는 'zero reading'을 가정함으로써 현장타설말뚝이나 항타말뚝의 시공시 발생된 잔류응력(the residual stress 또는 the residual load)을 무시하고 있다. 이러한 'zero reading'의 가정은 말뚝 시공시 발생하는 말뚝 하방향으로의 부주면마찰력인 잔류응력을 고려하지 않으므로 실제 말뚝주면의 하중분포와는 다른 결과를 보이게 된다. 본 연구에서는 현장에 시험시공된 현장타설말뚝에 대하여 정재하시험을 수행하였고, 말뚝 주면의 하중분포 측정시 변형률계를 사용하여 콘크리트 타설 직후부터 계측을 실시함으로써 말뚝 시공에 따른 잔류응력을 측정하였다. 그 결과, 잔류응력이 고려된 경우는 초기에 부의 응력상태를 보이나 하중이 재하됨에 따라 부주면마찰력이 극복되면서 양의 주면마찰력으로 전환됨을 알 수 있었으나, 'zero reading'의 경우는 양의 주면마찰력 만을 보였다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2017년도 제48회 춘계학술대회논문집
• /
• pp.310-319
• /
• 2017

충격파 시험장치를 이용하여 추력을 측정하는 방법을 소개하였다. 충격파 시험장치를 이용하여 엔진의 추력을 측정하기 위해서는 일반적인 엔진시험 시설에서 추력을 측정하기 위해 사용하는 밸런스가 힘의 평형상태에 도달하지 못하기 때문에 응력파 힘 밸런스(Stress Wave Force Balance) 방법을 이용하여 측정한다. 본 논문에서는 모델 힘 밸런스(force balance)에 대해 충격하중을 주고 유한요소법(FEM)으로 변형률을 계산하였다. 충격하중과 변형률의 관계를 역합성곱(de-convolution)하여 천이함수를 도출하였다.

• Journal of Welding and Joining
• /
• 제20권2호
• /
• pp.50-58
• /
• 2002

Residual stress is generated in the structures as a result of irregular elastic-plastic deformation during fabrication processes such as welding, heat treatment, and mechanical processing. There are several factors attributed to the origin of residual stresses, tensile or compressive. The stresses can be determined by destructive ways or nondestructive ways using X-ray or neutron diffraction. Although X-ray diffraction is a well established technique, it is practically limited to near-surface stresses. Neutrons penetrate easily into most materials and neutron diffraction permits non-destructive evaluation of lattice strain within the bulk of large specimens because the radiation is more deeply penetrating for metallic engineering components. This paper presented application of neutron diffraction technique to the residual stress measurement using 20 mm thick welded stainless steel plate($100{\times}100 \textrm{mm}^2$)

• 소성∙가공
• /
• 제16권2호
• /
• pp.101-106
• /
• 2007

Uniaxial displacement controlled tests were performed on annealed Type 304 stainless steel at room temperature. A servo-controlled testing machine and strain measurement on the gage length were employed to measure the response to a given input. The test results exhibit that the flow stress increases nonlinearly with the strain rate and the relaxed stress at the end of the relaxation periods depends strongly on the strain rate preceding the relaxation test. The rate-dependent inelastic deformation behavior is simulated using a new unified viscoplasticity model that has the rate-dependent format of nonlinear kinematic hardening rule, which plays a key role in modeling the rate dependence of relaxation behavior. The model does not employ yield or loading/unloading criteria and consists of a flow law and the evolution laws of two tensor and one scalar-valued state variables.