• Korean Journal of Microbiology
• /
• v.54 no.3
• /
• pp.200-207
• /
• 2018

At high salt concentration, glycine betaine is transported into Bacillus subtilis and growing rate of the cell is not suppressed. Also according to recent studies, cell growth is maintained normal growth rate at low temperature. Low temperature results in a stress response of Bacillus subtilis that is characterized by strong repression of major metabolic activities such as translation machinery and membrane transport. In this regards, genes showing cold sensitive phenotype are cold-induced DEAD box RNA helicases (ydbR, yqfR) and fatty acid desaturases (bkdR, des). Therefore to understand the effect of glycine betaine on cold growth of Bacillus subtilis, we investigated the effect of glycine betaine on growth rate of these deletion mutants showing cold sensitive phenotype. Glycine betaine strongly stimulated growth of wild type Bacillus subtilis JH642 and deletion mutants of ydbR and yqfR at $20^{\circ}C$ (190~686 min $T_d$ difference). On the other hands, glycine betaine does not show growth promoting effects on deletion mutants of bkdR, and des at cold conditions. Same cold protectant growth results were shown with the precursor choline instead of glycine betaine. We investigated the effects of detergents on the cell membrane in bkdR and des deficient strains associated with cell membrane. It was identified that bkdR deficient strain shows retarded growth with detergent such as Triton X-100 or N-lauryl sarcosine compared with wild type cell. Thus, it is possible that deletion mutation of bkdR modifies membrane structure and effects on transport of glycine betaine.

• Journal of the Society of Disaster Information
• /
• v.19 no.3
• /
• pp.572-581
• /
• 2023

Purpose: The purpose of this study is to improve the irregularity of the stress-strain curve and to ensure accuracy when calculating the damping effect by preventing members from moving in the off-plane direction due to eccentricity when loads are applied. Method: The specifications of the steel strips used in this study are the same, but the curvature of the strips to constitute each damper is different. Each steel strip with different curvature was arranged in an triangle, three dampers with different curvature were made, and repeated load tests were conducted, and the amount of energy dissipation was calculated to measure the performance of the damper. Result: The amount of energy dissipation significantly decreases compared to the case where there is no initial curvature, and the change in the test energy dissipation amount according to the size of the curvature is not large, and the presence or absence of the hyperbolic rate is considered an important variable. Conclusion: The period is about 78.7% longer from T=0.3 to T=0.536sec, and the response spectrum acceleration is reduced from Sa=0.54g to Sa=0.229g, so the damping effect of the damper is sufficient.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.28 no.2
• /
• pp.147-161
• /
• 2012

This study is to assess the effect of horizontal misfit of an implant supported 3-unit fixed prosthodontics on the stress development at the marginal cortical bone surrounding implant neck. Two finite element models consisting of a three unit fixed prosthodontics and an implant/bone complex were constructed on a three dimensional basis. The three unit fixed prosthodontics were designed either shorter (d=17.8mm model) or longer (d=18.0mm model) by 0.1mm than the span of two implants placed at the mandibular second premolar and second molar areas 17.9mm apart. Fitting of the fixed prosthodontics onto the implant abutments was simulated by a total of 6 steps, that is to say, 0.1mm displacement per each step, using DEFORM 3D (ver 6.1, SFTC, Columbus, OH, USA) program. Stresses in the fixed prosthodontics and implants were evaluated using von-Mises stress, maximum compressive stress, and radial stress as necessary. The d=17.8mm model assembled successfully on to the implant abutments while d=18.0mm model did not. Regardless if the fixed prosthodontics fitted onto the abutments or not, excessively higher stresses developed during the course of assembly trial and thereafter. On the marginal cortical bone around implants during the assembly, the peak tensile and compressive stresses were as high as 186.9MPa and 114.1MPa, respectively, even after the final sitting of the fixed prosthodontics (for d=17.8mm model). For this case, the area of marginal bone subject to compressive stresses above 55MPa, equivalent of the $4,000{\mu}{\varepsilon}$, i.e. the reported threshold strain to inhibit physiological remodeling of human cortical bone, extended up to 2mm away from implant during the assembly. Horizontal misfit of 0.1mm can produce excessively high stresses on the marginal cortical bone not only during the fixed prosthodontics assembly but also thereafter.

• Journal of the Korean Geotechnical Society
• /
• v.26 no.7
• /
• pp.49-58
• /
• 2010

This paper presents experimental results of a series of 1-g shaking table model tests performed on end-bearing single piles and pile groups to investigate the effect of particle size on the dynamic behavior of soil-pile systems. Two soil-pile models were tested twice: first using Jumoonjin sand, and second using Australian Fine sand. In the case of single-pile models, the lateral displacement was almost within 1% of pile diameter which corresponds to the elastic range of the pile. The back-calculated p-y curves show that the subgrade reaction of the Jumoonjin-sand-model ground was larger than that of the Australian Fine-sand-model ground at the same displacement. This phenomenon means that the stress-strain behavior of Jumoonjin sand was initially stiffer than that of Australian Fine sand. This difference was also confirmed by resonant column tests and compression triaxial tests. And the single pile p-y backbone curves of the Australian fine sand were constructed and compared with those of the Jumoonjin sand. As a result, the stiffness of the p-y backbone curves of Jumunjin sand was larger than those of Australian fine sand. Therefore, using the same p-y curves regardless of particle size can lead to inaccurate results when evaluating dynamic behavior of soil-pile system. In the case of the group-pile models, the lateral displacement was much larger than the elastic range of pile movement at the same test conditions in the single-pile models. The back-calculated p-y curves in the case of group pile models were very similar in both sands because the stiffness difference between the Jumoonjin-sand-model ground and the Australian Fine-sand-model ground was not significantly large at a large strain level, where both sands showed non-linear behavior. According to a series of single pile and group pile test results, the evaluation group pile effect using the p-multiplier can lead to inaccurate results on dynamic behavior of soil-pile system.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.20 no.2
• /
• pp.4645-4687
• /
• 1978

This study was attempted to investigate the mechanical properties of concrete and crack control effects of reinforced concrete with steel and glass fiber. The experimental program includes tests on the properties of fresh concrete containing fibers, compressive strength, tensile strength, flexural strength, Young's modulus, Shrinkage and deformation of steel or glass fiber reinforced concrete. Also this study was carried out to investigate the effect of steel or glass fiber to retard the development in reinforced concrete subject to uniaxial tension and thus facilitate the use of steels of higher strength. The major conclusions that can be drawn from the studies are as follows: 1. The effect of the fibers in various mixes on fresh concrete confirmed that fibers do have a significant effect on the properties of fresh concrete, bringing much more stable and exhibiting a signiflcant reduction in surface bleeding, and that the cohesion is greatly improved and the internal resistance increases with fiber concentration. But the addition of an excess contents and length of fibers brings about the reduction of workability. 2. With the addition of steel fibers(1.5% Vol.) to concrete, the compressive strength as compared with plain concrete showed a very slight increase, but excess addition, over 1.5% Vol. of steel and glass fiber reduced its strength. 3. Splitting tensile strength of fiber reinforced concrete showed a significant increase tendency, as compared with plain concrete. In case of containing steel fiber (2.5%, 30mm), it showed that the maximum increase rate of 1.48 times as much rate, and in case of containing glass fiber (2.5%, 30mm), the increase rate of strength was 1.25 times as much rate. 4. Flexural strength of fiber reinforced concrete showed a significant tendency, as compared with plain concrete. Containing steel fiber (2.5%, 30mm) showed the maximum increase rate of 1.64 times as much rate and containing glass fiber (2.5%, 30mm) showed the increase rate of strength of 1.32 times as much rate, and in general, the 30mm length brougth the best results. 5. The strength ratio ($\sigma$b/$\sigma$c and $\sigma$t/$\sigma$c) increased, when steel fiber's average spacing was up to 3.05mm, but decreased when beyond 3.05mm, and it was confirmed that tensile or flexural strengths of steel fiber reinforced concrete are apparently governed by fiber's average spacing. 6. The compressive strain of fiber reinforced concrete showed a significant increasing tendency as the fiber was added, but Young's modulus. with the addition of steel and glass fibers, showed a slight decrease tendency. And according to the increase of flexural strength, a considerable increase was seen in toughness. 7. With the addition of fiber's the shrinkage of concrete was significantly decreased, in both case of adding steel fibers 12.5%, 30mm, and showed a significant decrease ratio, in average 30.4% and 36.7%, as compared with plain concrete. 8. With the increase of fiber volume fraction and length, the gained stress in reinforcing bar in concrete specimens increased in all crack widths, but at different rates, with the decrease of fiber diameter, the stress showed a considerable increasing tendency. And the duoform steel fibers showed the greatest improvement, as compared with the other types tested. 9. The influence of fiber dimensions in order of significanse on the machanical properties of concrete and the crack control of reinforced concrete was explained as follows: content, length, aspect ratio and dimeter.

• Journal of the Korean Geosynthetics Society
• /
• v.4 no.2
• /
• pp.11-18
• /
• 2005

A pilot scale filed model test and 2-D numerical analysis was conducted to evaluate the effectiveness of constructing a geogrid-reinforced and pile-supported embankment system over soft ground to reduce differential settlement, and the results are presented hearin. Three-by-three pile groups with varying the space between pile were driven into a layer of soft marine clay and a layer of geogrid was used as reinforcement over each pile group. 2-D numerical analysis has been conducted by using the FLAC-2D(Fast Lagrangian Analysis of Continua) program for same condition of field model test. The settlement, vertical stress, and strain of geogrid due to the construction of embankment were measured at various locations. Based on the field model test and numerical analysis results, pile reinforcement generated the soil arching at the midspan of pile cap and the geogrid reinforcement helps reduce the differential settlement of the soft ground by tensile strength of geogrid. Also for $D/b{\geq}6.0$, the effectiveness of geogrid reinforcement in reducing settlement is negligible.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.14 no.3
• /
• pp.403-414
• /
• 1994

Nonlinear analysis of RC containment structure under thermal load and pressure is presented to trace the behaviour after an assumed LOCA. The temperature distribution varying with time through the wall thickness is determined by transient finite element analysis with the two time level scheme in time domain. The layered shell finite elements are used to represent the containment structures in nuclear power plants. Both geometric and material nonlinearities are taken into account in the finite element formulation. The constitutive relation of concrete is modeled according to Drucker-Prager yield criteria in compression. Tension stiffening model is used to represent the tensile behaviour of concrete including bond effect. The reinforcing bars are modeled by smeared layer at the location of reinforcements accounting elasto-plastic axial behaviors. The steel liner model under Von Mises yield criteria is adopted to represent elastic-perfect plastic behaviour. Geometric nonlinearity is formulated to consider the large displacement effect. Thermal stress components are determined by the initial strain concept during each time step. The temperature differential between any two consecutive time steps is considered as a load incremental. The numerical results from this study reveal that nonlinear temperature gradient based on transient thermal analysis will produces excessive large displacement. Nonlinear behavior of containment structures up to ultimate stage can be traced reallistically. The present study allows more realistic analysis of concrete containment structures in nuclear power plants.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.26 no.6
• /
• pp.423-430
• /
• 2013

In this research, a paramteric study to account for the effect of interfacial strength and nanotube agglomeration on the elastoplastic behavior of carbon nanotube reinforced polypropylene composites is performed. At first, the elastoplastic behavior of nanocomposites is predicted from molecular dynamics(MD) simulations. By combining the MD simulation results with the nonlinear micromechanics model based on the Mori-Tanaka model, a two-step domain decomposition method is applied to inversely identify the elastoplastic behavior of adsorption interphase zone inside nanocomposites. In nonlinear micromechanics model, the secant moduli method combined with field fluctuation method is used to predict the elastoplastic behavior of nanocomposites. To account for the imperfect material interface between nanotube and matrix polymer, displacement discontinuity condition is applied to the micromechanics model. Using the elastoplastic behavior of the adsorption interphase zone obtained from the present study, stress-strain relation of nanocomposites at various interfacial bonding condition and local nanotube agglomeration is predicted from nonlinear micromechanics model with and without the adsorption interphase zone. As a result, it has been found that local nanotube agglomeration is the most important design factor to maximize reinforcing effect of nanotube in elastic and plastic behavior.

• Journal of Life Science
• /
• v.23 no.7
• /
• pp.904-912
• /
• 2013

This study aimed to evaluate the protective effect of cordycepin-increased Cordyceps militaris strain on carbon tetrachloride ($CCl_4$)-induced hepatotoxicity and oxidative stress in rats. Male Sprague-Dawley rats were randomly divided into five groups (n=6) based on six dietary categories: normal (N), $CCl_4$ control (C), $CCl_4$ plus Paecilomyces japonica (CPJ) (3%, w/w), $CCl_4$ plus C. militaris (CCM) (3%, w/w), and $CCl_4$ plus cordycepin-increased C. militaris ($CCM{\alpha}$) (3%, w/w). The activities of the liver marker enzymes ALT, AST, and LDH and the levels of lipid peroxidation were increased in the $CCl_4$-treated groups, but these parameters were significantly decreased in the $CCM{\alpha}$ group. The TBARS content in the liver homogenate, microsome, and mitochondrial fractions of the C group was significantly elevated compared with the N group. However, in the $CCl_4$-treated groups, $CCM{\alpha}$ group was significantly lowered in the TBARS levels of hepatic homogenate and microsomal fractions. The C group showed a significant decrease in the levels of plasma and hepatic glutathione, whereas they were significantly increased in the $CCM{\alpha}$ group. Accordingly, cordycepin-increased C. militaris may be an ideal animal model for studying hepatoprotective effects.

• Applied Biological Chemistry
• /
• v.51 no.1
• /
• pp.1-5
• /
• 2008

Salt accumulation in soils of greenhouse due to the massive application of nitrogen fertilizers causes salt stress on the various crops, a serious problem in domestic agriculture. Since the majority of the salinity is nitrate, the excess nitrate should be removed; therefore, a bacterial strain having high capacity of nitrate uptake and identified as Enterobacter amnigenus GG0461 was isolated from the soils of greenhouse. Optimum conditions for the bacterial growth and nitrate uptake were investigated. GG0461 was able to grow without nitrate; however, nitrate facilitated the growth. The rate of nitrate uptake increased at alkaline pH and both growth and nitrate uptake were maximal at pH 8-9. When the initial pH of culture medium was increased to pH 8 or 9, it was decreased to neutral upon bacterial growth and nitrate uptake. These results imply that the major factor mediating bacterial nitrate uptake is a nitrate/proton antiporter. The fact was supported by the effect of nitrate addition in the absence of nitrate, since the addition of nitrate greatly increased the nitrate uptake and rapidly decreased pH of media.